Vacuum‐driven fluid manipulation by a piezoelectric diaphragm micropump for microfluidic droplet generation with a rapid system response time

Recently, we developed a convenient microfluidic droplet generation device based on vacuum‐driven fluid manipulation with a piezoelectric diaphragm micropump. In the present study built on our previous work, we investigate the influence of settings applied to the piezoelectric pump, such as peak‐to‐peak drive voltage (V_p‐p) and wave frequency, on droplet generation characteristics. Stepwise adjustments to the drive voltage in ±10‐V_p‐p increments over the range of 200?250 V_p‐p during droplet creation revealed that the droplet generation rate could be reproducibly controlled at a specific drive voltage. The droplet generation rate switched within <0.5 s after the input of a new voltage. Although the droplet generation rate depended on the drive voltage, this setting had almost no influence on droplet size. The frequency over the selected range (50?60 Hz) did not markedly influence the droplet generation rate or droplet size. We show that the current fluid manipulation system can be conveniently used for both droplet generation and for rapid droplet reading, which is required in many microfluidic‐based applications.     

Enhancement of optical and electrical properties of SILAR deposited ZnO thin films through fluorine doping and vacuum annealing for photovoltaic applications

Undoped and fluorine doped ZnO thin films were deposited onto glass substrates using successive ionic layer adsorption and reaction (SILAR) technique and then annealed at 350 °C in vacuum ambience. The F doping level was varied from 0 to 15 at% in steps of 5 at%. The XRD analysis showed that all the films are polycrystalline with hexagonal wurtzite structure and preferentially oriented along the (002) plane. Crystallite sizes were found to increase when 5 at% of F is doped and then decreased with further doping. It was seen from the SEM images that the doping causes remarkable changes in the surface morphology and the annealing treatment results in well-defined grains with an improvement in the grain size irrespective of doping level. All the films exhibit good transparency (>70%) after vacuum annealing. Electrical resistivity of the film was found to be minimum (1.32×10⁻³ Ω cm) when the fluorine doping level was 5 at%.     

X-ray radiography of aluminum cathodes eroded in high-current vacuum arcs

The aim of the study presented in this paper was to characterize quantitatively the erosion of aluminum cathodes in high-current vacuum arcs. The experimental setup comprised two current generators. The first one, capable of generating a current of amplitude up to 350 kA, was used to produce a plasma jet, that is, the object to be investigated. The second generator was used to produce a source of probe radiation for imaging the object under investigation in soft x rays of energy ?ν ≈ 0.5–3 keV. The findings of the study are based on experimental data obtained by electrophysical and radiographic methods. It has been shown that the cathode erosion rate in a high-current vacuum arc is a function of the charge passed through the cathode.     

Zero dissipation limit to rarefaction wave with vacuum for the one-dimensional non-isentropic micropolar equations

The zero dissipation limit of the one-dimensional non-isentropic micropolar equations is studied in this paper. If the given rarefaction wave which connects to vacuum at one side, a sequence of solution to the micropolar equations can be constructed which converge to the above rarefaction wave with vacuum as the viscosity and the heat conduction coefficient tend to zero. Moreover, the uniform convergence rate is obtained. The key point in our analysis is how to control the degeneracies in the vacuum region in the zero dissipation limit process.     

真空微电子荧光平板显示器件的实验研究

真空微电子荧光平板显示器件的实验研究刘杰明，李志能，陈秀峰（浙江大学信息与电子工程学系）关键词：真空微电子，反应离子刻蚀一、引言近十年来，随着真空微电子学的崛起，利用微细加工技术，使真空元器件集成化和高性能化已成为可能，一种新型场致发射阵列真空荧光平...     

国外MCM及其主要制造技术的发展现状

MCM具有胜过PCB、LSI和一般HIC的诸多优点,正在逢勃发展,可望成为九十年代的代表性技术。本文从市场和技术两个方面评述MCM的发展潜力,重点介绍近年来国外MCM主要制造技术的现状及发展态势,试图引起人们对它的关注。     

Development of Vacuum Monitoring System in the HL-2A tokamak

HL-2A is the first divertor tokamak in China. The vacuum system is one of the important parts of the HL-2A tokamak, which has to be work well during the physics campaign in 2004. As the tokamak machine is separated from the operation staff during discharges, to guarantee the safe and reliable operation of the vacuum system, it is necessary to watch the vacuum system outside the machine hall with an automatic monitoring system. The paper describes the design and manufacture of the monitoring system.     

用阻容保护装置抑制真空断路器的操作过电压

本文阐述了真空断路器用ＲＣ保护装置的原理。分析了用ＲＣ保护装置保护电力系统及其设备的试验结果。ＲＣ保护装置主要参数的选择。最后，讨论了有关ＲＣ保护装置的一些问题。     

Simulation of Vacuum Microelectronic Triode Made of Single Carbon Nanotube

Vacuum microelectronic triode performance, based upon a unit cell with a nanotube field emitter, gate, and anode, was evaluated via computer simulation. Electron emission was calculated from the modified Fowler-Nordheim equation. The dependence of emitted current, upon geometrical factors, e.g., nanotube radius, nanotube height, and gate's hole radius, is shown. The device design parameters of trans-conductance, and cutoff frequency have been calculated, which show that this structure can be used as a microwave and millimeter wave amplifier. Electron current flux is shown for time-dependent 1–Thz sinusoidal variation frequency input.