Optimization of Transducer Location for Novel Non-Intrusive Methodologies of Diagnosis in Diesel Engines

The health monitoring has been studied to ensure integrity of design of engine structure by detection, quantification, and prediction of damages. Early detection of faults may allow the downtime of maintenance to be rescheduled, thus preventing sudden shutdown of machines. In cylinder pressure developed, vibrations and noise emissions data provide a rich source of information about condition of engines. Monitoring of vibrations and noise emissions are novel non-intrusive methodologies for which positioning of various transducers are important issue. The presented work shows applicability of these diagnosis methodologies adopted in case of diesel engines. The effects of changing various fuel injection parameters was analyzed. Scope of using non-intrusive technique has been analyzed by changing locations of microphone. Novelty of this worklies in exploring signal processing methods for various locations around the engine test set up. Various frequency ranges of contributing noise and vibration sources were identified. Time-Frequency analysis showed the onset of various cyclic. Based on the identification of various frequency bands, it is possible to device suitable filters in order to extract more information.     

一种新型回路电阻测试仪的研究与设计

针对传统低压回路电阻测试仪只能在被测设备停电时使用的一大限制,本文提出并设计了一种新型低压回路电阻测试仪。该仪器可在低压设备运行状态下对其回路电阻进行测量,在保证测量精度的前提下减少了设备停电率,大大提高了工作效率。     

Vacuum‐driven fluid manipulation by a piezoelectric diaphragm micropump for microfluidic droplet generation with a rapid system response time

Recently, we developed a convenient microfluidic droplet generation device based on vacuum‐driven fluid manipulation with a piezoelectric diaphragm micropump. In the present study built on our previous work, we investigate the influence of settings applied to the piezoelectric pump, such as peak‐to‐peak drive voltage (V_p‐p) and wave frequency, on droplet generation characteristics. Stepwise adjustments to the drive voltage in ±10‐V_p‐p increments over the range of 200?250 V_p‐p during droplet creation revealed that the droplet generation rate could be reproducibly controlled at a specific drive voltage. The droplet generation rate switched within <0.5 s after the input of a new voltage. Although the droplet generation rate depended on the drive voltage, this setting had almost no influence on droplet size. The frequency over the selected range (50?60 Hz) did not markedly influence the droplet generation rate or droplet size. We show that the current fluid manipulation system can be conveniently used for both droplet generation and for rapid droplet reading, which is required in many microfluidic‐based applications.     

仪器仪表产品脉冲耐压试验要求和保护器件的选择

仪器仪表产品的脉冲耐压试验是产品型式试验、例行试验中的基本内容。通过对GB4793.1标准的整理,归纳了仪器仪表产品的脉冲耐压试验要求。通过对试验方法和设备特性的梳理,总结了特性参数,并介绍了应对脉冲耐压试验可采取的保护器件的类别及选用方法。     

Enhancement of optical and electrical properties of SILAR deposited ZnO thin films through fluorine doping and vacuum annealing for photovoltaic applications

Undoped and fluorine doped ZnO thin films were deposited onto glass substrates using successive ionic layer adsorption and reaction (SILAR) technique and then annealed at 350 °C in vacuum ambience. The F doping level was varied from 0 to 15 at% in steps of 5 at%. The XRD analysis showed that all the films are polycrystalline with hexagonal wurtzite structure and preferentially oriented along the (002) plane. Crystallite sizes were found to increase when 5 at% of F is doped and then decreased with further doping. It was seen from the SEM images that the doping causes remarkable changes in the surface morphology and the annealing treatment results in well-defined grains with an improvement in the grain size irrespective of doping level. All the films exhibit good transparency (>70%) after vacuum annealing. Electrical resistivity of the film was found to be minimum (1.32×10⁻³ Ω cm) when the fluorine doping level was 5 at%.     

X-ray radiography of aluminum cathodes eroded in high-current vacuum arcs

The aim of the study presented in this paper was to characterize quantitatively the erosion of aluminum cathodes in high-current vacuum arcs. The experimental setup comprised two current generators. The first one, capable of generating a current of amplitude up to 350 kA, was used to produce a plasma jet, that is, the object to be investigated. The second generator was used to produce a source of probe radiation for imaging the object under investigation in soft x rays of energy ?ν ≈ 0.5–3 keV. The findings of the study are based on experimental data obtained by electrophysical and radiographic methods. It has been shown that the cathode erosion rate in a high-current vacuum arc is a function of the charge passed through the cathode.     

Zero dissipation limit to rarefaction wave with vacuum for the one-dimensional non-isentropic micropolar equations

The zero dissipation limit of the one-dimensional non-isentropic micropolar equations is studied in this paper. If the given rarefaction wave which connects to vacuum at one side, a sequence of solution to the micropolar equations can be constructed which converge to the above rarefaction wave with vacuum as the viscosity and the heat conduction coefficient tend to zero. Moreover, the uniform convergence rate is obtained. The key point in our analysis is how to control the degeneracies in the vacuum region in the zero dissipation limit process.     

中国大陆PCB产业自动化的现况与未来

从中国大陆PCB发展的现况分析实行设备自动化连线为企业所创造的价值。设备自动化连线是中国大陆PCB必须面临的改革出路。     

贴片设备的选择

随着电子工业的飞速发展,贴片设备已被广泛应用于大规模电子组装生产上。文章就贴片机选型时应注意的几个关键技术问题作简单介绍,希望对企业选择贴装设备有一定的帮助。