Insights into MWCNTs/polyimide nanocomposites: from synthesis to application as free-standing flexible electrodes in low-cost micro-supercapacitors

In the pursuit to enlarge the library of polyimide materials for energy applications, new polyimide/MWCNTs composite films have been developed by MWCNTs-assisted polycondensation reaction of a hydroxyl and triphenylmethane-containing diamine with benzophenone tetracarboxylic dianhydride targeting to highlight their electrical storage capability as flexible electrodes in micro-supercapacitors (mSCs). The Fourier-transform infrared spectroscopy, proton nuclear magnetic resonance, UV–vis, fluorescence, and Raman spectroscopies were used to demonstrate the evolution of interfacial interactions between MWCNTs and the precursors (diamine monomer and intermediate polyamidic acid) and polyimide matrix that proved to be the origin of MWCNTs homogeneous dispersion. Thus, composite films incorporating 1, 3, 5, and 10 w.t.% MWCNTs were obtained and thoroughly investigated with regard to their morphology, mechanical behavior, thermal stability, and electrical conductivity. The electrochemical performance of these composites was first analyzed in a classical three-electrode cell by cyclic voltammetry and galvanostatic charge-discharge in both aqueous and organic electrolyte systems. By far, the best electrical storage capacity was obtained with the composite polyimide film containing 10% MWCNTs that was further used as both active material and current collector in a flexible symmetric mSC realized by a straightforward and low-cost procedure. In the attempt to better exploit the advantages of this composite film, it was layered with a graphite-containing paint and tested as an electrode in a flexible mSC, which provided satisfactory results. To our knowledge, this is the first report on the electrical charge storage capability of a polyimide/MWCNTs free-standing film as a flexible electrode in mSCs, which do not require time- and resource-consuming processing steps.     

Orientation dependent size effects in thermal buckling and post-buckling of nanoplates with cubic anisotropy

In this work, a continuum model is presented for size and orientation dependent thermal buckling and post-buckling of anisotropic nanoplates considering surface and bulk residual stresses. The model with von-Karman nonlinear strains and material cubic anisotropy of single crystals contains two parameters that reflect the orientation effects. Using Ritz method, closed form solutions are given for buckling temperature and post-buckling deflections. Regarding self-instability states of nanoplates and their recovering at higher temperatures, an experiment is discussed based on low pressurized membranes to verify the predictions. For simply supported nanoplates, the size effects are lowest when they are aligned in [100] direction. When the edges get clamped, the orientation dependence is ignorable and the behavior becomes symmetric about [510] axis. The surface residual stress makes drastic increase in buckling temperature of thinner nanoplates for which a minimum thickness is pointed to stay far from material softening at higher temperatures. Deflection of [100]-oriented buckled nanoplates is higher than [110] ones but this reverses at higher temperatures. The results for long nanoplates show that the buckling mode numbers are changed by orientation which is verified by FEM.     

大口径光学元件装夹转运结构设计及分析

为了实现大口径光学元件的安全装夹、转运,通过光学元件开槽与不开槽两种装夹方式的分析,得出开槽夹紧转运方式将带来微裂纹、应力集中、成本高等缺陷,提出了利用摩擦力克服光学零件的重力和惯性力的低应力装夹转运方案。通过对光学元件低应力夹紧结构设计,并利用有限元分析方法,得到不开槽装夹方式下,光学元件的最大主应力为1.11 MPa,最大切应力为0.73 MPa,远低于光学元件破坏的强度极限,且受力均匀,无应力集中现象。     

纵向泵浦Cr∶ Nd∶GSGG激光棒的热透镜效应研究

对纵向泵浦Cr∶Nd∶GSGG激光棒的热透镜效应进行了详细的理论分析。对温度分布的函数表达式 ,进行了讨论 ;分析了热引起的应力 ,得到了激光棒破裂的临界功率公式 ;最后对光学畸变进行了分析与讨论 ,推导了光程差计算公式     

数字电视用中分辨率74cm纯平彩色显像管BC配列不良的分析与对策

通过对74cm中分辨率纯平彩色显像管BC配列局部严重群散不良的调查分析,确定荫罩受力塌陷是主要原因,通过改良设计、工艺优化及其它方面的综合对策,使以上技术难题得到满意的解决,整管不良率由4.78%下降到0.172%。     

微桥法镍膜的弹性模量和残余应力测量

利用MEMS技术制作了不同尺寸的镍(Ni)膜微桥结构样品。采用纳米压痕仪XP系统测量了微桥载荷与位移的关系,并结合微桥力学理论模型得到了两种不同尺寸的Ni膜的弹性模量和残余应力。结果表明,两种不同尺寸的Ni膜的弹性模量结果一致,为190 GPa左右,但是残余应力变化较大。与采用纳米压痕仪直接测得的带有硅(Si)基底的Ni膜弹性模量186.8 7.5 GPa相比较,两者符合较好。     

Sensitivity analysis of thermal performances of flat plate solar air heaters

Sensitivity analysis is a mathematical tool, first developed for optimization methods, which aim is to characterize a system response through the variations of its output parameters following modifications imposed on the input parameters of the system. Such an analysis may quickly become laborious when the thermal model under consideration is complex or the number of input parameters is high. In this paper, we develop a mathematical model to analyse the heat exchanges in four different types of solar air collectors. When building this thermal model we show that for each collector, at quasi-steady state, the energy balance equations of the components of the collector cascade into a single first-order non-linear differential equation that is able to predict the thermal behaviour of the collector. Our heat transfer model clearly demonstrates the existence of an important dimensionless parameter, referred to as the thermal performance factor of the collector, that compares the useful thermal energy which can be extracted from the heater to the overall thermal losses of that collector for a given set of input parameters. A sensitivity analysis of our thermal model has been performed for the most significant input parameters such as the incident solar irradiation, the inlet fluid temperature, the air mass flow rate, the depth of the fluid channel, the number and nature of the transparent covers in order to measure the impact of each of these parameters on our model. An important result which can be drawn from this study is that the heat transfer model developed is robust enough to be used for thermal design studies of most known flat plate solar air heaters, but also of flat plate solar water collectors and linear solar concentrators.     

A novel and efficient synthesis of porphine

meso-Tetra(n-hexyloxycarbonyl)porphyrin was found to be converted into porphine, the mother compound of porphyrins, in a 77% yield when heated in aqueous sulfuric acid at 180 °C over 30 min under an inert atmosphere. The observation demonstrates that the substituted porphyrin serves as a novel and useful precursor for porphine.