THE effect of Srandom DOPANT fluctuation on threshold voltage and drain current variation in junctionless nanotransistors

We investigate the effect of dopant random fluctuation on threshold voltage and drain current variation in a two-gate nanoscale transistor. We used a quantum-corrected technology computer aided design simulation to run the simulation (10000 randomizations). With this simulation, we could study the effects of varying the dimensions (length and width), and thicknesses of oxide and dopant factors of a transistor on the threshold voltage and drain current in subthreshold region (off) and overthreshold (on). It was found that in the subthreshold region the variability of the drain current and threshold voltage is relatively fixed while in the overthreshold region the variability of the threshold voltage and drain current decreases remarkably, despite the slight reduction of gate voltage diffusion (compared with that of the subthreshold). These results have been interpreted by using previously reported models for threshold current variability, load displacement, and simple analytical calculations. Scaling analysis shows that the variability of the characteristics of this semiconductor increases as the effects of the short channel increases. Therefore, with a slight increase of length and a reduction of width, oxide thickness, and dopant factor, we could correct the effect of the short channel.     

A simple three‐wave approximate Riemann solver for the Saint‐Venant‐Exner equations

Erosion and sediments transport processes have a great impact on industrial structures and on water quality. Despite its limitations, the Saint‐Venant‐Exner system is still (and for sure for some years) widely used in industrial codes to model the bedload sediment transport. In practice, its numerical resolution is mostly handled by a splitting technique that allows a weak coupling between hydraulic and morphodynamic distinct softwares but may suffer from important stability issues. In recent works, many authors proposed alternative methods based on a strong coupling that cure this problem but are not so trivial to implement in an industrial context. In this work, we then pursue 2 objectives. First, we propose a very simple scheme based on an approximate Riemann solver, respecting the strong coupling framework, and we demonstrate its stability and accuracy through a number of numerical test cases. However, second, we reinterpret our scheme as a splitting technique and we extend the purpose to propose what should be the minimal coupling that ensures the stability of the global numerical process in industrial codes, at least, when dealing with collocated finite volume method. The resulting splitting method is, up to our knowledge, the only one for which stability properties are fully demonstrated.     

内插法在相关干涉仪测向体制中的应用

测向误差的减小一直以来都是无线电测向精度提高的一个难点,对于不同的测向体制所采用的减小测向误差的方法都不尽相同。本文主要介绍的是相关干涉仪测向体制的基本原理以及通过内插法的应用来减小测向误差的方法。     

Positive ground state solutions for Schrödinger–Poisson system with critical nonlocal term in ℝ3

This paper is dedicated to studying the following Schrödinger–Poisson system $$\left\{\begin{array}{ll}-\mathrm{\Delta }u+V(x)u-K(x)\varphi |u{|}^{3}u=a(x)f(u),& x\in {ℝ}^3,\\ -\mathrm{\Delta }\varphi =K(x)|u{|}^5,& x\in {ℝ}^3.\end{array}\right.$$ Under some different assumptions on functions V(x), K(x), a(x) and f(u), by using the variational approach, we establish the existence of positive ground state solutions.     

QEPAS系统中石英音叉模态仿真计算与研究

对石英音叉增强型光声光谱(QEPAS)系统中常用的石英音叉进行了有限元模态计算，获得石英音叉前6阶振型与模态频率，认知了第4阶对称摆动振型为有效振动，利用单因素法分析了石英音叉的音臂长度l₁、音臂宽度w₁、音臂厚度t、音臂切角θ、音臂圆孔直径d及音臂圆孔高度h对低阶有效共振频率(Fre)的影响，敏感度依次为： l₁> w₁>d>θ>t>h，考虑实际设计情形，筛选出了l₁，w₁，d与h四个石英音叉设计变量，采用Box-Behnken实验设计方案与RSM(response surface methodology)方法，以Fre为函数目标，建立l₁，w₁，d与h的二次回归响应面模型，得到了参数之间的交互作用，利用Design-Expert软件对响应面模型进行设计参数反求，结果表明，在15 000 Hz≤Fre≤25 000 Hz计算区域内误差较小，基本满足QEPAS系统的计算需求，所提出的研究与设计方法具有一定通用性，可为QEPAS系统中石英音叉结构参数设计提供参考。     

软件集成测试技术研究

首先分析了集成测试的原理和特点，并指出了集成测试的重要性。然后结合传统软件与面向对象软件开发的方法和技术，详细介绍了传统软件的集成测试方法和策略，并深入分析了面向对象软件集成测试的原理和方法。     

光折变三维信息存储器

分析光折变三维存储器的机理,探讨了光折变三维存储器的编码方式、光折变材料的选择及存储技术,阐述了其产业化进程.     

Ku波段波导型双工器的研制

采用高精度的模式匹配法设计了一种Ku波段波导型双工器。双工器采用H面T接头和E面横向膜片波导带通滤波器。采用该方法设计的双工器精度高，结构简单，便于加工。文中也将理论结果和实测数据进行了比较，两者吻合得很好，证明了模式匹配法的精确性和有效性。