Effect of sodium doping on graded Cu(In1−xGax)Se2 thin films prepared by chemical spray pyrolysis

In the present work we have studied the effect of Na on the properties of graded Cu(In_1−xGa_x)Se₂ (CIGS) layer. Graded CIGS structures were prepared by chemical spray pyrolysis at a substrate temperature of 350 °C on soda lime glass. Sodium chloride is used as a dopant along with metal (Cu/In/Ga) chlorides and n, n-dimethyl selenourea precursors. The addition of Na exhibited better crystallinity with chalcopyrite phase and an improvement in preferential orientation along the (112) plane. Energy dispersive analysis of X-rays (line/point mapping) revealed a graded nature of the film and percentage incorporation of Na (0.86 at%). Raman studies showed that the film without sodium doping consists of mixed phase of chalcopyrite and CuAu ordering. Influence of sodium showed a remarkable decrease in electrical resistivity (0.49–0.087 Ω cm) as well as an increase in carrier concentration (3.0×10¹⁸–2.5×10¹⁹ cm⁻³) compared to the un-doped films. As carrier concentration increased after sodium doping, the band gap shifted from 1.32 eV to 1.20 eV. Activation energies for un-doped and Na doped films from modified Arrhenius plot were calculated to be 0.49 eV and 0.20 eV, respectively. Extremely short carrier lifetimes in the CIGS thin films were measured by a novel, non-destructive, noncontact method (transmission modulated photoconductive decay). Minority carrier lifetimes of graded CIGS layers without and with external Na doping are found to be 3.0 and 5.6 ns, respectively.     

Charge injection in metal/organic/metal structures with ZnO:Al/organic interface modified by Zn1−xMgxO:Al layer

Aluminum-doped zinc oxide (ZnO:Al, AZO) electrodes were covered with very thin (∼6 nm) Zn_1−xMg_xO:Al (AMZO) layers grown by atomic layer deposition. They were tested as hole blocking/electron injecting contacts to organic semiconductors. Depending on the ALD growth conditions, the magnesium content at the film surface varied from x = 0 to x = 0.6. Magnesium was present only at the ZnO:Al surface and subsurface regions and did not diffuse into deeper parts of the layer. The work function of the AZO/AMZO (x = 0.3) film was 3.4 eV (based on the ultraviolet photoelectron spectroscopy). To investigate carrier injection properties of such contacts, single layer organic structures with either pentacene or 2,4-bis[4-(N,N-diisobutylamino)-2,6-dihydroxyphenyl] squaraine layers were prepared. Deposition of the AMZO layers with x = 0.3 resulted in a decrease of the reverse currents by 1–2 orders of magnitude and an improvement of the diode rectification. The AMZO layer improved hole blocking/electron injecting properties of the AZO electrodes. The analysis of the current-voltage characteristics by a differential approach revealed a richer injection and recombination mechanisms in the structures containing the additional AMZO layer. Among those mechanisms, monomolecular, bimolecular and superhigh injection were identified.     

Fully solution-processed and multilayer blue organic light-emitting diodes based on efficient small molecule emissive layer and intergrated interlayer optimization

Efficient and fully solution-processed blue organic light-emitting diodes (OLEDs) based on fluorescent small-molecule and methanol/water soluble conjugated polymer as electron-injection material are reported. The emitting layer is 3,6-bis(9,9,9′,9′-tetrakis (6-(9H-carbazol-9-yl)hexyl)-9H,9′H-[2,2′-bifluoren]-7-yl)dib-nzo[b, d]thiophene 5, 5-dioxide (OCSoC) with a blue-fluorescent small-molecule, and a methanol/water soluble polymer poly[(9,9-bis(30-(N,N-dimethylamino)propyl)-2,7-fluorene)-alt-2,7-(9,9-dioctyl-fluorene)] (PFN) acted as electron-injection layer (EIL). All the organic layers are spin-coated from solution. The multilayer device structure with emitting layer/electron-injection layer is achieved by solution-processed method without the dissolution problem between layers. The performances of the devices show that the maximum luminous efficiency of the multilayer device is increased about 43%, compared to the single-layer device. PFN acting as the EIL material plays a key role in the improvement of the device performance when used in solution-processed small-molecule OLEDs.     

Long-wavelength light emission from InAs quantum dots covered by GaAsSb grown on GaAs substrates

We fabricated InAs quantum dots (QDs) with a GaAsSb strain-reducing layer (SRL) on a GaAs(0 0 1) substrate. The wavelength of emission from InAs QD is shown to be controllable by changing the composition and thickness of the SRL. An increase in photoluminescence intensity with increasing compositions of Sb and thickness of the GaAsSb SRL is also seen. The efficiency of radiative recombination was improved under both conditions because the InAs/GaAsSb/GaAs hetero-interface band structure more effectively suppressed carrier escape from the InAs QDs.     

Energy Spectrum Width and Nonequilibrium Energy of Rayleigh Waves Scattered on a Two-Dimensional Near-Surface Electron Layer

We obtain expressions for the energy spectrum widths of Rayleigh waves corresponding to their deformational coupling to Fermi and Boltzmann electrons in a two-dimensional layer near the surface of a semibounded solid. We evaluate the nonequilibrium energy of Rayleigh waves that depends on these widths and is caused by the same coupling to the corresponding hot electrons. We show that this energy is independent of the degeneracy degree of the electrons and is given by the mean energy of free Rayleigh waves heated up to temperature of the electrons. We find conditions under which the thermodynamics is determined by this nonequilibrium energy of Rayleigh waves in films of a certain thickness with Fermi electrons near the surface and by the equilibrium energy of bulk phonons in thicker samples. All the results are obtained using the Keldysh diagram technique applied to the case of semibounded media.     

Evaluation of Digitally Encoded Layer‐by‐layer Coated Microparticles as Cell Carriers

To obtain more biologically relevant data there is a growing interest in the use of living cells for assaying the biological activity of unknown chemical compounds. Density ‘multiplex’ cell‐based assays, where different cell types are mixed in one well and simultaneously investigated upon exposure to a certain compound are beginning to emerge. To be able to identify the cells they should be attached to microscopic carriers that are encoded. This paper investigates how digitally encoded microparticles can be loaded with cells while keeping the digital code in the microcarriers readable. It turns out that coating the surface of the encoded microcarriers with polyelectrolytes using the layer‐by‐layer (LbL) approach provides the microcarriers with a ‘highly functional’ surface. The polyelectrolyte layer allows the growth of the cells, allows the orientation of the cell loaded microcarriers in a magnetic field, and does not hamper the reading of the code. It has further been shown that the cells growing on the polyelectrolyte layer can become transduced by adenoviral particles hosted by the polyelectrolyte layer. It is concluded that the digitally encoded microparticles are promising materials for use in biomedical and pharmaceutical in‐vitro research where cells are used as tools.     

Crystallographic report: catena‐Aqua(2,2′‐bipyrimidine)lithium(I) perchlorate

A lithium(I) coordination polymer has been formed from LiClO₄ and the 2,2′‐bipyrimidine (bpym) ligand in which each square pyramidal lithium(I) atom is coordinated in the basal plane by four nitrogen donor atoms derived from two bpym ligands and one water molecule at the apical position. These are connected into a layer structure via hydrogen‐bonding interactions involving the perchlorate anions. Copyright © 2004 John Wiley & Sons, Ltd.     

A note on the unsteady boundary layers over a flat plate

The unsteady boundary layer over a semi-infinite flat plate was investigated in this paper. The flow involves the unsteady flow over a flat plate with leading edge accretion or ablation. The momentum boundary layer was further analyzed and it was shown that the leading edge ablation had a similar effect to the wall mass injection or upstream wall movement making the fluid blown away from the wall. The thermal boundary layer of the same flow was also studied. Results show that the leading edge accretion or ablation can greatly change the fluid motion and the heat transfer characteristics.     

Closed-form solutions for a rectangular layer with central crack under anti-plane shear stress

We consider the problem of determining the stress distributionin a finite rectangular elastic layer containing a Griffithcrack which is opened by internal shear stress acting alongthe length of the crack. The mode III crack is assumed to belocated in the middle plane of the rectangular layer. The followingtwo problems are considered: (A) the central crack is perpendicularto the two fixed lateral surfaces and parallel to the othertwo stress-free surfaces; (B) all the lateral surfaces of therectangular layer are clamped and the central crack is parallelto the two lateral surfaces. By using Fourier transformations,we reduce the solution of each problem to the solution of dualintegral equations with sine kernels and a weight function whichare solved exactly. Finally, we derive closed-form expressionsfor the stress intensity factor at the tip of the crack andthe numerical values for the stress intensity factor at theedges of the cracks are presented in the form of tables.