焦炉上升管内壁结焦炭层的光谱学分析及结焦机理研究

以焦炉上升管内壁结焦炭层块为研究对象，采用X射线荧光光谱仪（XRF）、X射线衍射仪（XRD）、傅里叶红外光谱仪（FTIR）和激光共聚焦拉曼光谱仪（Raman）对结焦炭层的元素组成，以及各结焦炭层的矿物组成、组成结构和分子结构进行测试。分析从结焦炭层块外表面向内表面过渡的各结焦炭层的差异性，揭示焦炉上升管内壁结焦机理。结果表明焦炉上升管内粉尘中Fe，S和Cr极易催化荒煤气中蒽、萘等稠环芳烃化合物成炭，在焦炉上升管内壁形成炭颗粒沉积，为焦油凝结挂壁提供载体，在荒煤气温度降至结焦温度时易结焦积碳。结焦炭层均含有芳香层结构，随着结焦炭层从外表面向内表面过渡，各结焦炭层的面层间距(d₀₀₂)逐渐降低、层片直径(L_a)先降低后增加、层片堆砌高度(Lc)和芳香层数(N)先稳定后增加。结焦炭层石墨化过程是由结焦炭层内表面向外表面进行，主要包括其片层外缘的羧基和部分C-O结构的降解剥离，从而形成高度规整的共轭结构。结焦炭层块中C元素是以结晶碳与无定型碳的混合物形式存在。以上研究为解决焦炉上升管内壁结焦及腐蚀问题，提高换热器换热效率，有效回收焦炉荒煤气显热，降低焦化企业能耗提供实验基础和理论依据。     

机抖激光陀螺抖动机构的温度特性的研究

研究了机抖激光陀螺抖动偏频量与温度之间的关系。通过大量的重复性高低温实验,证明了抖动偏频量与温度的线性关系,并得到了拟合直线表达式。结果表明,抖动偏频量与温度具有较好的线性关系,而且具有较好的重复性。同时用抖动偏频量对陀螺的零漂进行补偿,提高了陀螺的精度。     

激光熔覆专用铁基合金粉末的研究进展

指出了目前防止熔覆层开裂所采取的主要措施中存在的问题,阐述了激光熔覆和热喷涂对于所用合金粉末性能要求之异同,评述了激光熔覆专用铁基合金粉末的研制现状,提出了成分与组织设计的新思想。     

Real time estimation of CO2 laser weld quality for automotive industry

Laser welding is one of the most precise welding processes in joining sheet metals. In laser welding, performing real time evaluation of the welding quality is very important to enhance the efficiency of the welding process. In this study, the plasma and spatter, which are generated during laser welding, are measured using UV and IR photodiodes. The factors that influence weld quality are classified into five categories; optimal heat input, slightly low heat input, low heat input, partial joining due to gap mismatch, and nozzle deviation. The data number deviated from reference signals and their standard deviations were also considered to evaluate the qualities. A system was also formulated to perform real time evaluations of the weld quality using a fuzzy multi-feature pattern recognition with the measured signals.     

Scattering of Laser Light from Mixed Micelles

Dynamic and static scattering of light was employed to investigate mixed micelles of two homologous anionic surfactants-sodium octyl sulfate and sodium hexadecyl sulfate, above the phase boundary temperature and critical micelle concentrations (cmc). The results indicate that the mixed micelles change from prolate to sphcrical as the molar ratio SOS/SHS increases from 1 to 8. Below 1 or above 8, the formation of micelles is due to one surfactant dissolving the other.     

激光熔覆Ni基SiC合金涂层组织与性能的研究

利用5kWCO2连续波激光器在16Mn钢基材表面对含20%(体积比)SiC陶瓷粉末的镍基自熔性合金粉末进行激光熔覆得到Ni基SiC合金涂层(NiSiC)。研究了合金涂层的组织形貌及相结构,并用单纯的镍基合金涂层(Ni60)进行了显微硬度及滑动磨损性能的对比试验。结果表明,NiSiC合金涂层由γ枝晶及其间的共晶组织组成,主要组成相为γ-Ni,γ-(Ni,Fe)固溶体和(Cr,Fe)7C3,Cr23C6及(Cr,Si)3Ni3Si等化合物。添加SiC的镍基合金涂层NiSiC比单纯的镍基合金涂层Ni60具有较高的硬度和耐磨性。     

Laser induced copper electroless plating on polyimide with Q-switch Nd:YAG laser

The results of laser induced deposition of copper on polyimide substrate from copper electrolyte solution are reported. Unlike most work reported in the literatures where CW Ar⁺ lasers were used, a second harmonic (532 nm wavelength) Q-switch Nd:YAG laser was used for our experiments. The deposition process was conducted by laser-catalyzing of the polyimide surface and subsequent photothermal-accelerated reduction of copper-complex ions in an alkaline reducing environment. The characteristics of the deposited copper line were investigated in terms of laser beam scanning speed, and the number of scans. The surface morphology and chemical composition of the deposited copper were analyzed using field emission scanning electron microscope (FESEM) and energy dispersive spectrometer (EDX). The optimum processing conditions have been identified. The copper deposit was found to adhere well to the substrate.     

一种高信噪比的双光束激光光声光谱仪原理及应用

作为一种新兴的检测手段 ,激光光声光谱技术与其他检测技术相比具有很多优点。本文设计的光声光谱仪用激光做光源 ,有两个光声池 ,分别用来放置参考样品和待测样品 ,输出结果为二者光声信号的比值。利用这一比值 ,可以由参考样品的性能参数方便地求出待测样品的相关性能参数。该光声光谱仪有效地减小了本底吸收噪声的影响 ,提高了信噪比 ,扩大了固体光声理论的应用范围。本文还阐述了该光声光谱仪在定性定量分析中的一些应用     

Reciprocating sliding wear behavior of laser-clad small amplitude Mo2Ni3Si/NiSi metal silicide composite coatings

Mo₂Ni₃Si/NiSi metal silicide composite coatings with a fine microstructure consisting of Mo₂Ni₃Si primary dendrites and the interdendritic Mo₂Ni₃Si/NiSi eutectics were fabricated on austenitic stainless steel AISI 321 by laser cladding process. Small amplitude reciprocating sliding wear resistance of the coatings is evaluated as functions of normal load and slip amplitude and the wear mechanisms were discussed based on worn surface morphology observations. Results showed that the Mo₂Ni₃Si/NiSi coatings have excellent small amplitude reciprocating sliding wear resistance.     

Radiative lifetimes in Ce I and Ce II

New radiative lifetime measurements based on time-resolved laser-induced fluorescence techniques are reported for 18 even-parity levels belonging to the 4f5d^26p and 4f ²5d ² configurations of Ce I and 6 even-parity levels belonging to the 5d^26s, 4f5d6p, and 4f6s6p configurations of Ce II. Free neutral and singly ionized cerium atoms were produced by laser ablation. The Ce I and Ce II levels range in energy from 26 545 to 29 102 cm^-1, and 42 573 to 48 152 cm^-1, respectively. Received 25 September 2002 Published online 4 March 2003