Novel structure of GaAs-based interdigital-gated HEMT plasma devices for solid-state THz wave amplifier

Theoretical analysis of potential distribution in the interdigital-gated high electron mobility transistor (HEMT) plasma wave device was carried out. The dc I–V characteristics of capacitively coupled interdigital structure showed that uniformity of electric field under the interdigital gates was improved compared to the dc-connected interdigital gate structure. Admittance measurements of capacitively coupled interdigital gate structure in the microwave region of 10–40 GHz showed the conductance modulation by drain–source voltage. These results indicate the existence of plasma wave interactions.     

基于声表面波技术实现数字微流体多基片间输运

建立了声表面波实现多基片间输运微流体的新方法.由3个128(0)YX-LiNbO3压电基片组成,一个基片为接口基片,另两个为工作基片,每个基片光刻一个中心频率为27.5 MHz叉指换能器和一个反射栅.采用微量进样器将待输运的数字微流体进样到工作基片2,调节接口基片使得其与工作基片2位于同一高度,并使其间隙尽可能小,在工...     

平面交叉指状电极间电场分布

研究了具有金属－半导体－金属结构的探测器内部电场与其几何尺寸的关系，并求出使探测器内部电场的均匀性，稳定性达到最佳的几何条件。     

集成电容设计的逆向神经网络建模

结合人工神经网络和电磁仿真,给出了一种用于综合交指电容及Metal-Insulator-Metal(MIM)电容结构参数的方法。基于逆向神经网络,可有效地根据给定频点上的电容值快速准确地综合出其对应的结构参数,从而避免了反复优化的过程。同时,可以由训练好的神经网络参数得到结构参数相对于等效电容的闭式计算公式。数值结果验证了方法的正确性和有效性。     

Roller-type gravure offset printing of conductive inks for high-resolution printing on ceramic substrates

The use of gravure offset printing methods at an industrial level requires a wide and deep knowledge of the printing properties of the inks. Novel hydrocarbon inks were developed with superior printing properties compared to alternative ethyl cellulose-based inks. There are principal behaviour properties of these inks that can be generally described. In particular, the resistance dependence of printed mass for single and multiprints and on the other hand, the effect of multiprinting on printed area smoothness and line height.

This article summarizes the results obtained and describes printing properties and defects: line widening, hair formation, ink flow from the gravure grooves, pinholes, image distortions, ribbing, scooping, streaking and gravure groove blocking. Three different printed samples were demonstrated, which are best suited for this manufacturing method: interdigital capacitor, inductor coil and laser soldering substrates.     

Design of interdigital transducers for crack detection in plates

Interdigital transducers (IDT) for non-destructive evaluation (NDE) of cracks in plates are designed based on an analytical model established previously. Key considerations include mode selectivity, excitation strength, collimation of wave and cost. The advantage of mode selectivity of IDT over PZT patch is presented both analytically and experimentally. Effects of parameters, namely finger spacing, width, length, number of fingers, and the size of IDT, on the excitation strength and mode selectivity are considered. This led to the design of a mobile double-sided IDT as an efficient device where excitation strength is strong and focused. The device was fabricated in-house using commercially available piezoelectric ceramics and used to develop a procedure for accurate identification of the direction and extent of cracks in plates. Three aluminum plates, one with a linear deep crack, another with a piecewise linear shallower crack and the third with a curved crack, were used to illustrate the accuracy and efficiency of both the proposed device and procedure for effective NDE.     

宽阻带抑制的高温超导带通滤波器设计

提出了一种新型加载插指电容的U型阶跃阻抗谐振器,该谐振器可用于实现高温超导带通滤波器的宽阻带抑制。利用所提出的新型谐振器结构,设计并制作了一个4节切比雪夫型高温超导带通滤波器。滤波器中心频率为1026 MHz,带宽12.6 MHz,第一谐频频率5121 MHz,第一谐频与基频的比值为4.92,阻带抑制度优于60 dB。     

叉指换能器新的等效电路模型及其PSPICE仿真

声表面波器件PSPICE仿真是包含声表面波器件电子系统设计的难点,文章提出了适于PSPICE仿真的叉指换能器新等效电路模型,它应用LC网络等效Mason等效电路模型的复阻抗,由Y导纳矩阵推导计算声表面波器件的二阶效应频率特性,根据电路理论综合出与Y矩阵得到的声表面波器件二阶特性相同的等效电路,并与主信号叉指换能器等效电路模型叠加,PSPICE仿真结果与实验结果在中心频率处插入损耗和带宽相符.     

MMDS上下变频器的微带叉指带通滤波器

微带叉指带通滤波器具有结构紧凑，易于批量生产的特点，可用于ＭＭＤＳ接收机中作为镜象频率抑制滤波器或用于上变频器中滤除噪波。文中给出有关设计公式，并举出设计实例，微带基片采用ＲＯ４００３改进型高频环氧玻璃纤维板。     

Design and validation of miniaturize Rat Race Coupler based microstrip Balun

This work presents a compact Balun with enhanced bandwidth and better isolation between output ports using Interdigital Capacitor (IDC). Firstly, a Rat Race Coupler (RRC) is designed, later Balun is proposed by replacing the isolation port with a 50 Ω isolation resistor. The proposed Transmission line (TL) is designed using an IDC in parallel with a high impedance TL. Based on a π-equivalent circuit the proposed TL has been investigated and optimized to achieve 70.7 Ω impedance. The Balun is designed and fabricated. The simulated and fabricated results are in accord. The fractional bandwidth (FBW) of RRC and Balun are 37.5% and 33% respectively at centre frequency 2.4 GHz. The size occupied by the proposed Balun is 0.51λ_g × 0.22λ_g. The structure is low cost, uniplanar and compact.