Facile non‐lithographic route to highly aligned silica nanopatterns using unidirectionally aligned polystyrene‐block‐polydimethylsiloxane films

Thin films (monolayer and bilayer) of cylinder forming polystyrene‐block‐polydimethylsiloxane (PS‐b‐PDMS) were shear aligned by the swelling and deswelling of a crosslinked PDMS pad that was physically adhered to the film during solvent vapor annealing. The nanostructures formed by self‐assembly were exposed to ultraviolet‐ozone to partially oxidize the PDMS, followed by calcination in air at 500 °C. In this process, the PS segments were fully decomposed, while the PDMS yielded silica nanostructures. The highly aligned PDMS cylinders were thus deposited as silica nanolines on the silicon substrate. Using a bilayer film, the center‐to‐center distance of these features were effectively halved from 38 to 19 nm. Similarly, by sequential shear‐alignment of two distinct layers, a rhombic array of silica nanolines was fabricated. This methodology provides a facile route to fabricating complex topographically patterned nanostructures. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1058–1064     

AGE method simulations of a turbulent far‐wake compared to spectral DNS

Turbulent flow simulation methods based on finite differences are attractive for their simplicity, flexibility and efficiency, but not always for accuracy or stability. This paper demonstrates that a good compromise is possible with the advected grid explicit (AGE) method. Starting from the same initial field as a previous spectral DNS, AGE method simulations of a planar turbulent wake were carried out as DNS, and then at three levels of reduced resolution. The latter cases were in a sense large‐eddy simulations (LES), although no specific sub‐grid‐scale model was used. Results for the two DNS methods, including variances and power spectra, were very similar, but the AGE simulation required much less computational effort. Small‐scale information was lost in the reduced resolution runs, but large‐scale mean and instantaneous properties were reproduced quite well, with further large reductions in computational effort. Quality of results becomes more sensitive to the value chosen for one of the AGE method parameters as resolution is reduced, from which it is inferred that the numerical stability procedure controlled by the parameter is acting in part as a sub‐grid‐scale model. Copyright © 2002 John Wiley & Sons, Ltd.     

稀疏过程在破产问题中的应用

本讨论一类人寿保险的风险过程，其中保单到达服从齐次Poisson过程。而描述退保及索赔发生的计数过程分别为这一过程的q-稀疏与p-稀疏．对此模型给出其破产概率的具体上界，并与其它一类风险模型进行比较．     

Closed-form solutions for a rectangular layer with central crack under anti-plane shear stress

We consider the problem of determining the stress distributionin a finite rectangular elastic layer containing a Griffithcrack which is opened by internal shear stress acting alongthe length of the crack. The mode III crack is assumed to belocated in the middle plane of the rectangular layer. The followingtwo problems are considered: (A) the central crack is perpendicularto the two fixed lateral surfaces and parallel to the othertwo stress-free surfaces; (B) all the lateral surfaces of therectangular layer are clamped and the central crack is parallelto the two lateral surfaces. By using Fourier transformations,we reduce the solution of each problem to the solution of dualintegral equations with sine kernels and a weight function whichare solved exactly. Finally, we derive closed-form expressionsfor the stress intensity factor at the tip of the crack andthe numerical values for the stress intensity factor at theedges of the cracks are presented in the form of tables.     

A numerical and experimental investigation of the interactions between a non‐uniform planar array of incompressible free jets

The interaction between multiple incompressible air jets has been studied numerically and experimentally. The numerical predictions have been first validated using experimental data for a single jet configuration. The spreading features of five unequal jets in the configuration of one larger central jet surrounded by four smaller equi‐distant jets, have been studied, for different lateral spacing ratios of 1.5, 2.0 and 2.5 and a central jet Reynolds number of 1.24×105 (corresponding to a Mach number of 0.16). Flow of five equal jets has also been simulated, for the sake of comparison. The jet interactions commence at an axial distance of about 3–4 diameters and complete by an axial distance of about 10 diameters for the lowest spacing ratio of 1.5. For larger spacing ratios, the length required for the start and completion of jet interaction increase. Peripheral jets bend more towards the central jet and merge at a smaller distance, when their sizes are smaller than that of the central jet. The entrainment ratio for multiple jets is higher than that for a single jet. Excellent agreement is observed between the experimental data and theoretical predictions for both mean flow field and turbulent quantities, at regions away from the jet inlet. The potential core length and initial jet development, however, are not predicted very accurately due to differences in the assumed and actual velocity profiles at the jet inlet. Copyright © 2004 John Wiley & Sons, Ltd.     

Shear banding in strained semicrystalline polyamide 6 films as revealed by atomic force microscopy: Role of the amorphous phase

Atomic force microscopy (AFM) has been used to visualize the plastic deformation mechanisms that are responsible for the yielding of semicrystalline polymers of low degree of crystallinity (<50%). Indeed, AFM, if operated in suitable conditions, is able to image both the amorphous and the crystalline phases. Polyamide 6 films have been drawn at temperatures T < 160 °C. Postmortem AFM observations show that, at yield, shear bands nucleate and propagate in the amorphous phase. They cross the crystalline lamellae and run over the whole surface of the sample. By crossing the lamellae, they form nanoblocks of uniform size. Neither the size of the nanoblocks nor the angle between the tensile axis and the shear bands can be explained in terms of crystal plasticity. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 687–701, 2004     

提高三维激光扫描系统图像质量技术的研究

对其中三维激光扫描图像处理的关键技术———二值化、细化以及离散数据点云的滤波进行了研究,提出了一种先加权中值滤波,然后再小波分析滤波的新的降噪方法,并通过遗传算法对权重值进行了优化。在通常情况下,由于小波分析计算工作量大,所以提出了一种相对简单的算法,实现了在单台PC机上的运算。     

Stress State of Multilayer Thin-Walled Elements with Interfacial Defects of Structure

Based on the discrete-structural theory of thin plates and shells, a calculation model for thin-walled elements consisting of a number of rigid anisotropic layers is put forward. It is assumed that the transverse shear and compression stresses are equal on the interfaces. Elastic slippage is allowed over the interfaces between adjacent layers. The solution to the problem is obtained in a geometrically nonlinear statement with account of the influence of transverse shear and compression strains. The stress-strain state of circular two-layer transversely isotropic plates, both without defects and with a local area of adhesion failure at their center, is investigated numerically and experimentally. It is found that the kinematic and static contact conditions on the interfaces of layered thin-walled structural members greatly affect the magnitude of stresses and strains. With the use of three variants of calculation models, in the cases of perfect and weakened contact conditions between layers, the calculation results for circular plates are compared. It is revealed that the variant suggested in this paper adequately reflects the behavior of layered thin-walled structural elements under large deformations. __________ Translated from Mekhanika Kompozitnykh Materialov, Vol. 41, No. 6, pp. 761–772, November–December, 2005.     

集中荷载下叠合梁抗剪强度

本文对低叠合面钢筋破简支在合梁二阶段受力的斜截面抗剪性能进行了试验研究，并运用非线性有限元分析和试验实测数据，得出了一个适合于集中荷载下高低叠合面叠合梁的抗剪强度计算公式．     

A proof of Howard’s conjecture in homogeneous parallel shear flows

A rigorous mathematical proof of Howard's conjecture which states that the growth rate of an arbitrary unstable wave must approach zero, as the wave length decreases to zero, in the linear instability of nonviscous homogeneous parallel shear flows, is presented here for the first time under the restriction of the boundedness of the second derivative of the basic velocity field with respect to the vertical coordinate in the concerned flow domain.