堇青石窑具多晶结构与性能研究

利用X-射线衍射分析和电子显微镜分析的结果，确定堇青石窑具的多晶结构和各晶相的含量；结合窑具性能的研究，确定堇青石窑具具有优良性能的适宜配方。     

A high‐precision instrument for mapping of rotational errors in rotary stages

A rotational stage is a key component of every X‐ray instrument capable of providing tomographic or diffraction measurements. To perform accurate three‐dimensional reconstructions, runout errors due to imperfect rotation (e.g. circle of confusion) must be quantified and corrected. A dedicated instrument capable of full characterization and circle of confusion mapping in rotary stages down to the sub‐10 nm level has been developed. A high‐stability design, with an array of five capacitive sensors, allows simultaneous measurements of wobble, radial and axial displacements. The developed instrument has been used for characterization of two mechanical stages which are part of an X‐ray microscope.     

基于改进极根学习机的回转窑煅烧带温度预测方法

针对传统算法预测回转窑煅烧带温度存在精度低、速度慢的问题,提出了基于改进极限学习机(ELM)的回转窑煅烧带温度预测方法。对ELM输入权值矩阵定义了变换系数,采用黄金分割法在给定区间内搜寻变换系数的最佳值,改进了ELM网络参数的确定方式,弥补了随机确定输入权值并且不作调整的缺陷,在保证ELM训练速度的前提下提高预测精度、减小模型随机性。实验结果表明,改进的ELM预测精度高、训练速度快、模型性能优,可满足工况恶劣的回转窑的生产需要。     

Research on application of polynomial fitting technique in rotary kiln infrared temperature measurement system

Aiming at the linear temperature compensation algorithm’s disadvantage of temperature measurement error in rotary kiln infrared scanning temperature measurement process, this paper proposes a precise nonlinear cubic polynomial fitting temperature compensation algorithm. The proposed algorithm compensates the temperature values of scanning points on rotary kiln surface by following steps: Calculating temperature difference between the real temperature value of rotary kiln and temperature value measured by infrared scanning temperature measurement system; Fitting the temperature difference data with cubic polynomial; Using the obtained function to compensate temperature. Experimental result shows that compared with the usual linear temperature compensation algorithm, the accuracy of proposed algorithm has raised about 2.25 times when cubic polynomial is used.     

基于工作电流分析的回转副摩擦状态识别实验研究

回转副摩擦状态的变化对机械设备的运行有着重要影响. 针对回转副摩擦状态的识别问题, 设计了以回转副工作电流为摩擦特征来源的实验方案. 通过采集摩擦过程的回转副驱动电机工作电流信号, 分析实验信号的频域和时频域特征, 建立工作电流的摩擦特征库, 用于训练多分类支持向量机分类器, 并在分类器上完成摩擦状态的识别. 实验结果表明, 经特征提取与降维处理后建立的多分类支持向量机分类器具有近90%的识别正确率, 所提出的实验方案有利于实现远距离信号的采集, 适用实际生产加工.     

基于AVR单片机的万能材料试验机控制系统

采用AVR单片机AT90S8515作为控制核心,通过步进电机带动丝杠运动,利用光栅编码器、高精度力传感器、2个引伸计分别测量了位移、力及试件横、纵变形,在老式电子万能材料实验机上建立了新型计算机控制系统,可方便测定弹性模量和泊松比.     

双层旋转壳流固耦合振动有限元分析

本文采用旋转壳体元和流体元分析了双层旋转壳体流固耦合振动特性,基于Novozhilov壳体理论、水弹性理论以及Hamilton变分原理推导出耦合系统运动方程,计算结果与实测值比较表明本分析方法有较好的精度。     

Influence of MnO_2 Mineralizer on the Crystal Structure,Properties of SiC Kiln Furniture Bonded with Fine Silicon Powder

lINTRODUCTIONSiCkilnfllrniturepossessesgoodhigh-temperaturepropertiesandsmoothness.Itishighlyresistanttowarddeforming,slaggingandthermalshock.Thefurniturecanpracticallyresultinimprovingqualityandproductionofceramicsandiswidelyusedovertheworld.However,SiChassinteringtemperatureofupto2OOO:Ct13landitisdifficulttosinterasproductbyusingcommonkilnfurnace.Toserveashigh-temperaturerefractorykilnfurniture,itmustbemixedwithabonder.Thisworkus-esfinesiliconpowderasabonder,whichisadustproducedfroms…     

关于平行光束的聚焦

根据费马原理，设想出一个由旋转椭球面与半径等于椭球短半轴的球面组成的透镜，使具有一定宽度的平行光束通过透镜后聚焦。     

基于包层旋转折变型光纤光栅的动态增益均衡器

提出并利用高频CO₂激光脉冲在普通单模通信光纤上写出了包层旋转折变型长周期光纤光栅(R-LPFG). 在分析R-LPFG波导结构和双折射特性的基础上，对光栅周期数和折变旋转度分别为50和7.2°/周期的R-LPFG进行了实验研究.结果表明，这种类型的光栅可极大地降低其谐振波长对横向负荷不同作用方向所表现出的方向相关性，并且其谐振峰幅度横向负荷灵敏度在任意方向下均高达0.37dB/(g·mm^-1) ，是普通LPFG横向负荷灵敏度的9倍左右.利用R-LPFG的温度线性响应特性和独特的横向负荷特性，设计并实验研究了一种动态增益均衡器，用其平坦掺铒光纤放大器增益谱，在C波段32nm范围内，其平坦度小于±0.5dB，可满足实际环境对通信系统的平坦应用要求. 关键词： 光纤通信技术 长周期光纤光栅 动态增益均衡 旋转折变