Calcium-based coordination polymers from a solvothermal synthesis of HKUST-1 in 3D printed autoclaves

A mixed-metal 1D coordination polymer [CaCu(HBTC)₂(H2O)₈]_n (where H₃BTC – benzene-1,3,5-tric arboxylic acid) was obtained in a solvothermal synthesis of a well-known copper-containing metal–organic framework [Cu₃(BTC)₂(H₂O)₃]_n (HKUST-1) in autoclaves 3D-printed from commercial polypropylene. This material was a source of calcium ions, apparently, leaking from a colorant (calcium carbonate) promoted by glacial acetic acid as a modulator used to produce large single crystals of HKUST-1. This finding was confirmed by elemental analysis and a model experiment that resulted in a new calcium-based 1D coordination polymer [Ca(H₂BTC)₂(H₂O)₅]_n under the same solvothermal conditions with no copper or calcium salts put into a 3D-printed autoclave.     

Highly Luminescent Red Phosphorescent OLED with Interfacial Layers for Hole Transport and Electron Injection

Four kinds of red phosphorescent organic light-emitting devices were fabricated and compared to investigate the effect of interfacial layers for hole transport and electron injection. 1 nm-thick LiF in the device A and C and 1 nm-thick Cs₂CO₃ in the device B and D were deposited as an electron injection layer between the anode and the electron transport layer, and 5 nm-thick layer of dipyrazion[2,3-f:2′,2′-h]quinoxaline-2,3,6,7,10,11-hexacarbonitrile[HATCN] was inserted as a hole transport interfacial layer between the hole injection layer and the hole transport layer only in the device C and D. Under a luminance of 1000 cd/m², the power efficiencies were 7.6 lm/W and 8.5 lm/W in the device A and B, and 8.6 lm/W and 13.4 lm/W in the device C and D. The quantum efficiency of the device D was 15.8% under 1000 cd/m² which was somewhat lower than those of the device A and C, but a little higher than that of the device B. The luminance of the device D was much higher than those of the other devices at a given votage. The luminance of the device D at 7 V was 23,710 cd/m², which was 13.0, 3.4, and 4.0 times higher than those of the device A, B, and C at the same voltage, respectively.     

一阶最优性条件研究

本对由Botsko的关于多变量函数取极值的一阶导数检验条件定理^[1]进行了分析研究，给出了更实用而简捷的差别条件。最后，举出若干例子予以说明。     

光束发散度对紫外写入光纤光栅的影响

用傅里叶衍射光学分析了准分子激光束发散度对于光纤光栅制备的影响，发现光束发散角使光纤光栅的布拉格波长发生改变，相位版后干涉场沿光纤轴向和径向不均匀，对制备30dB高反射率光纤光栅造成困难。实验结果与理论分析基本一致，相对于理想平行光束情况，会聚光束使得光纤光栅布拉格波长出现在短波一边，发射光束使得光纤光栅布拉格波长出现在长波一边。     

HIRFL–CSR加速器中束流与真空中剩余气体的碰撞损失

研究了重离子加速器中束流与真空中剩余气体的碰撞损失过程和碰撞截面,在依据大量实验数据的基础上,提出了一组计算离子一原子的电荷交换截面的经验公式.以兰州重离子加速器HDRFL及冷却储存环CSR为例,给出了依据碰撞截面的公式计算束流在加速器真空中的传输效率的方法,并计算了在不同真空度下HIRFL的ECR源轴向注入束运线、注入器SFC、前束运线、主加速器SSC和后束运线等不同加速阶段及CSR的传输效率,并提出合理的真空度要求.HIRFL的真空分布测量和束流的损失测量证明了该计算方法的可靠性.     

半导体激光器光束准直系统的功率耦合效率

在长距离无线光通信中，接收点光功率密度与光束发散角平方呈反比关系，为了获得小的发散角和大的功率耦合效率，要求准直系统有较大的数值孔径(NA)，但数值孔径过大会增加像差，因此合理设计功率耦合效率与准直系统的数值孔径就非常重要。该文对半导体激光器光束准直系统中功率耦合效率进行了研究，给出了半导体激光器光束功率耦合效率与k(孔径半径与孔径处等效光束半径之比)的关系表达式，并结合激光器光束准直系统，给出了半导体激光器光束功率耦合效率与准直系统数值孔径的关系表达式。该研究结论对于半导体激光器光束准直系统设计具有参考作用。     

Focusing and diffraction by an optical lens and a small circular aperture

Based on the vectorial Rayleigh–Sommerfeld diffraction integrals, analytical expressions for the transversal and axial field distribution of plane waves propagating through a thin lens followed by a small circular aperture are derived and used to study the focusing and diffraction properties of plane waves. Some special cases of our general result are discussed, and illustrative numerical calculation results are given. It is found that the vectorial nonparaxial approach should be applied if the aperture dimension is comparable with the wavelength or the focusing is strong.     

Surface structures formed by individual adsorption and coadsorption of Mn and Bi on Cu(0 0 1), studied by LEED

We have studied the individual adsorption of Mn and Bi, and their coadsorption on Cu(0 0 1) by low-energy electron diffraction (LEED). For Mn, we have determined the c(2 × 2) structure formed at 300 K, whose structure had been determined by several methods. We reconfirmed by a tensor LEED analysis that it is a substitutional structure and that a previously reported large corrugation (0.30 Å) between substitutional Mn and remaining surface Cu atoms coincides perfectly with the present value. In the individual adsorption of Bi, we have found a c(4 × 2) structure, which is formed by cooling below ∼250 K a surface prepared by Bi deposition of ∼0.25 ML coverage at 300 K where streaky half-order LEED spots appear. The c(4 × 2) structure has been determined by the tensor LEED analysis at 130 K and it is a substitutional structure. In the coadsorption, we found a c(6 × 4) structure, which has been determined by the tensor LEED analysis. It is very similar to the previously determined structure of the c(6 × 4) formed by coadsorption of Mg and Bi, and embedded MnBi₄ clusters are arranged in the top Cu layer instead of MgBi₄. Large lateral displacements of Bi atoms in the c(6 × 4)-(Mn + Bi) suggest that the Mn atoms undergo the size-enhancement caused by their large magnetic moment.     

Effect of the Parameters of Three-Mirror Resonators on the Spectral Characteristics of Single-Pulse Laser Generation with Self-Injection of Priming Radiation

Based on a semiclassical theory, investigations were made of the dynamics and spectral composition of pulsed generation with self-injection of priming radiation from the active part of a three-mirror linear resonator, the passive part of which contains an active loss modulator and serves as the output reflector of the laser. It is shown that there exists a range of resonator parameters at which pulsed lasing has virtually a single frequency irrespective of the detuning of the frequencies of the priming radiation and of the nearest eigenmode of the composite resonator. Considering graphically the phase conditions of generation, it is established that among pulsed lasers with self-injection of priming radiation which are constructed on the basis of three-mirror linear and branched resonators, the most efficient for creating single-frequency generation are those in which the length of the main resonator, where generation of the pulse occurs, is larger than the length of the additional one intended for forming the priming radiation. With an inverse ratio of the lengths of the resonators, the conditions of single-frequency pulsed generation becomes dependent on the priming radiation frequency.     

用变形全息透镜实现变形分数傅里叶变换

利用一发散点光源和一束倾斜平行光制作出在两个垂直方向上具有不同焦距的变形全息透镜,且用此全息元件实现了变形分数傅里叶变换。变形全息透镜两个方向上的焦距随全息记录条件和再现条件而变化,分析了用这种全息透镜实现变形分数傅里叶变换的条件。实验表明,用该元件能够方便地实现任意级次的变形分数傅里叶变换。