带有无限到达源的Re-entrant Line的稳定性

用Foster判别准则,Weiss[13]给出了带有无限到达源的两站三步re-entrant line的稳定性的充分条件．本文用两种不同的方法得到了其稳定性的充分必要条件,即: 二维随机游动方法和Foster判别准则．同时,我们又用流体模型方法得到了系统稳定的充分条件,大大地简化了Weiss[13]的证明．     

射流对绕水翼云空化流动抑制机理研究

为理解绕水翼云空化流动的发展机理和探究水翼吸力面开孔射流的影响,采用密度 修正的RNG $k$-$\varepsilon $湍流模型和Schnerr-Sauer空化模型对原始NACA66(mod) 水翼和采用射流后的 水翼的云空化非定常过程进行模拟和对比分析;采用在水翼吸力面近壁区设立监测线的方法对近壁区的流场进行监测,得到 近壁区汽相体积分数、回射流速度、压力及压力梯度的时空分布云图;开展了云空化流场特性的涡动力学分析,进而分析水 翼云空化的发生机理和射流抑制空化的抑制机理. 结果表明:游离型空泡在下游溃灭时产生强烈的局部高压,其向上游传播 导致前缘空穴的一次回缩,而空穴的二次回缩受回射流的影响. 回射流的发展区域受限于较高的压力梯度,高的压力梯度一 直存在,但回射流在一个周期内的首次出现需要时间的积累. 在水翼吸力面射流使得射流孔附近压力升高,弥补了由于空化 和绕流造成的压降,压力梯度增大,抗逆压能力增强,对回射流起到阻挡作用;另一方面,射流使得回射流区域面积和回射 流的强度也有所减小,从而对云空化的发展起到抑制的效果. $Q$准则的涡结构云图相比于汽相体积分数云图能显示复杂的 流动结构,前缘附着型空穴和尾缘游离型空穴内存在旋涡,回射流对空穴存在剪切作用造成空穴脱落. 而射流对空穴和回射 流的剪切和阻挡使云空化发展得到抑制.      

主动射流控制水翼空化的数值模拟与分析

为了改善高速流动工况下水翼吸力面上流场的空化特性,提出了水翼表面主动射流对绕水翼周围流动加以控制的方法.基于密度分域滤波的FBDCM混合湍流模型联合Zwart-Gerber-Belamri空化模型,分析了来流空化数为0.83,来流攻角为8°,射流位置距水翼前缘为x=0.19c时,主动射流对于水翼吸力面上流动的空化特性和水动力特性影响.对回射流的强度进行了量化分析,以探究回射流与流场空化特性的关系.数值分析结果表明,在射流水翼吸力面上的时均空泡体积为原始水翼的1/15,使得流场内空化流动由云空化状态转变为较为稳定的片空化状态,显著地削弱了云空化的发展.此外,射流极大地改善了水翼的水动力性能,使得水翼的升阻比较原始水翼提高了22.9%,空泡的脱落频率减少了26.2%,空泡脱落所引起的振幅减小了9.1%.射流大幅降低了水翼吸力面上低压区面积,水翼吸力面上流体的逆向压力减小,回射流强度降低;同时,射流使水翼吸力面上的边界层减薄,增强了流动的抗逆压梯度能力,一定程度上阻挡了回射流向水翼前缘的流动,这也从机理上分析了主动射流抑制空化的原因.      

The flow of an Oldroyd fluid around a sharp corner

A similarity solution is constructed for the flow of an Oldroyd-B fluid around a 270° re-entrant comer. The velocity is found to vanish like r^5/9 and the stress to be singular like r^−2/3. A simple expression is found for the streamfunction.     

空泡流非稳态现象的流动控制

处于跨临界阶段的空泡流必然导致强烈的周期性冲击和振动,空泡流的激振来源于空泡云的周期性大规模脱落,空泡云的形成和发展与流动的边界层效应有着强烈的相关性,且空泡末端的局部流动直接影响空泡流的整体稳定性,本试验在NACA16012水翼表面粘附一条展向1mm厚10mm宽的挡流条,尝试以干扰水翼上表面局部流动的方法来影响整个空泡流的形态及其流动稳定性,最终在一定的空泡数范围内抑制了空泡流激振现象,并从试验研究的角度探索了空泡云脱落的机理。     

Minimizing total earliness and tardiness on re-entrant batch processing machine with time windows

The time window (TW) generalizes the concept of due date. The semiconductor wafer fabrication system is currently one of the most complex production processes, which has typical re-entrant batch processing machine (RBPM). RBPM is a bottleneck. This paper addresses a scheduling of RBPM with job-dependent TWs. According to a general modelling, an improved and new job-family-oriented modelling of the decomposition method that is based on the slack mixed integer linear programming is proposed. First, the complicated scheduling problem of RBPM is divided into sub-problems, which are executed circularly. Then, each one consists of updating, sequencing and dispatching. The objective is to minimize the total earliness and tardiness for job-dependent TWs. In order to evaluate the proposed modelling, the experiments are implemented on the real-time scheduling simulation platform and optimization toolkit ILOG CPLEX. The results show that the improved modelling obtains better solutions in less computation time.     

Design of a re-entrant double-staggered ladder circuit for V-band coupled-cavity traveling-wave tubes

The re-entrant double-staggered ladder slow-wave structure is employed in a high-power V-band coupled-cavity traveling-wave tube. This structure has a wide bandwidth, a moderate interaction impedance, and excellent thermal dissipation properties, as well as easy fabrication. A well-matched waveguide coupler is proposed for the structure. Combining the design of attenuators, a full-scale three-dimensional circuit model for the V-band coupled-cavity traveling-wave tube is constructed. The electromagnetic characteristics and the beam-wave interaction of this structure are investigated. The beam current is set to be 100 mA, and the cathode voltage is tuned from 16.8 kV to 15.8 kV. The calculation results show that this tube can produce a saturated average output power over 100 W with an instantaneous bandwidth greater than 1.25 GHz in the frequency ranging from 58 GHz to 62 GHz. The corresponding gain and electronic efficiency can reach over 32 dB and 6.5%, respectively.     

Ferrimagnetism in two antiferromagnetic transverse Ising thin films

The phase diagrams and temperature dependences of total magnetization m_T in two antiferromagnetic transverse Ising thin films with same thickness L (L = 4), consisting of two (A and B) layers, are studied by the uses of the effective-field theory with correlations and the mean-field theory. The A and B layers are consisted of spin-1/2 atoms and they have opposite spin directions. Two magnetic structures are discussed and they exhibit rather different and characteristic behaviors for the magnetic properties. Many characteristic behaviors observed in standard ferrimagnetic materials as well as novel phenomena have been obtained for the thermal variations of m_T in the both systems, when the crystallographically equivalent conditions between the A and B layers are broken.     

含不相关机的动态可重入柔性流水车间问题的混合DABC-GA算法

为了改善生产线的物流平衡和加强阶段间的时间衔接,扩展一般可重入柔性流水车间调度理论,以最小化总加权完工时间为目标,研究了每阶段含不相关并行机的动态可重入柔性流水车间问题,工件在各阶段的加工时间取决于加工它的机器。鉴于所研究问题为NP-hard问题,首先,建立整数规划模型;其次,设计元胞矩阵编码方案,提出融合离散人工蜂群算法和遗传算法的一种混合算法以获得问题的近优解;最后,为了评估混合算法的性能,将所提出算法和一些元启发式算法进行了不同规模问题的对比测试,实验结果说明了所提算法的有效性。     

云状空化非定常脱落机理的数值与实验研究

结合数值计算和实验技术研究了云状空化的非定常脱落机理. 实验采用高速录像技术观察了绕Clark-y型水翼云状空化形态随时间的变化. 数值计算采用了汽-液两相的当地均相流模型,湍流封闭采用了一种修正的RNG k-\varepsilon方程,利用商业软件的二次开发技术,引入了一种与空化区域水汽相密度相关的系数,对湍流模型进行了修正. 计算和实验结果均表明:云状空化尾部存在着准周期性的涡状空化团的脱落;局部压强的增加是引起空穴断裂进而脱落的直接原因;压强升高是由于近壁处的反向射流引起的;空穴尾部的大规模的旋涡运动引起的近壁处的逆压梯度是引起反向射流的主要原因.