Correlation between the Mechanical Properties and the Amount of Desorbed Water for Composites Based on Low-Density Polyethylene and Linen Yarn Production Waste

The effect of the amount of desorbed water on the mechanical properties of composites based on low-density polyethylene and linen yarn production waste (LW) is analyzed by statistical methods. It is shown that the amount of absorbed water decreases during the desorption process at room temperature both for specimens modified and unmodified with diphenylmethane diisocyanate (DIC.) The most sensitive to the action of water is the elastic modulus, which decreases considerably under the effect of water and is fully restored in the desorption process. The tensile strain also increases with the amount of absorbed water. It is found that the elastic modulus of the unmodified composite correlates linearly with the amount of desorbed water. Between the amount of desorbed water and the tensile strain, as well the specific work of deformation, a negative linear correlation is revealed. After water desorption, all strength and deformation characteristics of both the modified and unmodified composites are fully recovered.__________Translated from Mekhanika Kompozitnykh Materialov, Vol. 41, No. 4, pp. 515–524, July–August, 2005.     

Mechanical Properties of Blends of Low-Density Polyethylene with Chlorinated Polyethylene

The results of experimental investigation into the mechanical properties of blends of low-density polyethylene (LDPE) with chlorinated polyethylene (CPE) in tension are presented. The specimens of pure LDPE, CPE, and nine types of LDPE/CPE blends, with different content of components at 10 wt.% intervals, were examined. Data on the influence of blend composition on the tensile stress-strain diagram, elastic modulus, yield stress, breaking stress, and ultimate elongation are obtained. The results of investigations of creep are also reported. It is found that the creep compliance (the total current compliance minus the elastic compliance) obeys the power law of creep.__________Translated from Mekhanika Kompozitnykh Materialov, Vol. 41, No. 3, pp. 391–404, May–June, 2005.     

Application of the essential work of fracture concept to nanostructured polymer materials

The first part of the paper deals with a critical discussion of the methodical basis of essential work of fracture (EWF) concept with respect to the specimen geometry (especially the notch depth) and application to polymers. In the second part, an in situ testing device, which combines a tensile testing machine with an optical strain-field measuring system, has successfully demonstrated possibility of characterization of fracture behaviour of polystyrene-polybutadiene block copolymers and block copolymer/homopolymer blends as examples of nanostructured polymer materials. It has been shown that knowledge of the time evolution of the strain field close to the crack tips leads to a simple verification of the basic precondition for the applicability of the EWF concept, the precondition “plastic zone coalescence-before-stable crack propagation”.     

Effect of monomer concentration on characteristics of methacrylic acid-grafted polyethylene film prepared by photografting

The effect of monomer concentration on photografting of methacrylic acid (MAA) onto linear low-density polyethylene (PE) film (thickness=30 μm) was investigated at 60 °C in water solvent together with the location of MAA-grafted chains. Xanthone was used as a photoinitiator which was coated on the film sample earlier. The higher percentage of grafting and graft efficiency were afforded for the system with the higher monomer concentration. The resultant MAA-grafted films were subjected to measurements of pH-responsive character and ability to adsorb cupric ion in order to understand the characteristics of function introduced. The grafted samples exhibited the pH-responsive character, where they shrank and swelled in acidic and alkaline media, respectively. The pH-responsive character of the grafted films was higher for the samples prepared in the system with a higher monomer concentration. Moreover, the grafted samples exhibited the ability to adsorb cupric ion, and the ability was reduced when the sample was prepared in the system with a higher monomer concentration. The different extents of the pH-responsive character and ability to adsorb cupric ion of the resulting grafted PE films were discussed in terms of location of grafted chains in the film substrate, which was determined by a scanning electron microscope and an attenuated total reflection infrared spectroscopy.     

Diffusion in Lorentz lattice gas automata with backscattering

The probability of first return to the initial intervalx and the diffusion tensorD _x are calculated exactly for a ballistic Lorentz gas on a Bethe lattice or Cayley tree. It consists of a moving particle and a fixed array of scatterers, located at the nodes, and the lengths of the intervals between scatterers are determined by a geometric distribution. The same values forx andD _x apply also to a regular space lattice with a fraction of sites occupied by a scatterer in the limit of a small concentration of scatterers. If backscattering occurs, the results are very different from the Boltzmann approximation. The theory is applied to different types of lattices and different types of scatterers having rotational or mirror symmetries.     

Transport properties of the Lorentz gas: Fourier's law

We investigate the stationary nonequilibrium (heat transporting) states of the Lorentz gas. This is a gas of classical point particles moving in a region gL containing also fixed (hard sphere) scatterers of radiusR. The stationary state considered is obtained by imposing stochastic boundary conditions at the top and bottom of , i.e., a particle hitting one of these walls comes off with a velocity distribution corresponding to temperaturesT ₁ andT ₂ respectively,T ₁ <T ₂. Letting be the average density of the randomly distributed scatterers we show that in the Boltzmann-Grad limit,,R 0 with the mean free path fixed, the stationary distribution of the Lorentz gas converges in theL ¹-norm to the stationary distribution of the corresponding linear Boltzmann equation with the same boundary conditions. In particular, the steady state heat flow in the Lorentz gas converges to that of the linear Boltzmann equation, which is known to behave as (T ₂-T ₁)/L for largeL, whereL is the distance from the bottom to the top wall: i.e., Fourier's law of heat conduction is valid in the limit. The heat flow converges even in probability. Generalizations of our result for scatterers with a smooth potential as well as the related diffusion problem are discussed.Research supported in part by NSF Grant no. Phy 77-22302.On leave of absence from the Fachbereich Physik der Universität, München. Work supported by a DFG fellowship.     

Degradation-fragmentation of marine plastic waste and their environmental implications: A critical review

This review critically evaluates the plastic accumulation challenges and their environmental (primarily) and human (secondarily) impacts. It also emphasizes on their degradation and fragmentation phenomena under marine conditions. In addition, it takes into account the leachability of the various chemical substances (additives) embedded in plastic products to improve their polymeric properties and extend their life. Regardless of their effectiveness in enhancing the polymeric function of plastic products, these additives can potentially contaminate air, soil, food, and water. Several findings have shown that, regardless of their types and sizes, plastics can be degraded and/or fragmented under marine conditions. Therefore, the estimation of fragmentation and degradation rates via a reliable developed model is required to better understand the marine environmental status. The main parameter, which is responsible for initiating the fragmentation of plastics, is sunlight/UV radiation. Yet, UV- radiation alone is not enough to fragment some plastic polymer types under marine conditions, additional factors are needed such as mechanical abrasion. It should be also mentioned that most current studies on plastic degradation and fragmentation centered on the primary stages of degradation. Thus, further studies are needed to better understand these phenomena and to identify their fate and environmental effects.     

Morphological,thermal, and biodegradation properties of LLDPE/treated date palm waste composite buried in a soil environment

In this study, date palm waste that was naturally treated as a filler in a linear-low density polyethylene (LLDPE) matrix was recycled to prepare green composites. Two types of LLDPE, based on basic additives, were used. UV stabilizer and the slip and anti-block were added as basic additives. The objective of this study was to examine the effect of these basic additives and the treated filler on the biodegradation, morphological, and thermal properties of the prepared samples by a soil burial test. The samples were characterized by Fourier-transform infrared (FT-IR) spectroscopy and X-ray diffraction (XRD). Weight loss was calculated to investigate the biodegradation of the sample, and SEM and thermogravimetric analyses were performed to reveal the morphology and thermal properties before and after burial, respectively. Results showed that the presence of the bio-filler accelerated the biodegradation of the composites. The UV stabilizer had a positive impact on biodegradation factors whereas anti-block additives appeared resistant to biodegradable factors. The morphology and thermal stability of all the prepared samples changed after burial due to the effects of biodegradation during the burial.     

Studying the Suitability of Nineteen Lignins as Partial Polyol Replacement in Rigid Polyurethane/Polyisocyanurate Foam

In this study, nineteen unmodified lignins from various sources (hardwood, softwood, wheat straw, and corn stover) and isolation processes (kraft, soda, organosolv, sulfite, and enzymatic hydrolysis) were used to replace 30 wt.% of petroleum-based polyol in rigid polyurethane/polyisocyanurate (PUR/PIR) foam formulations. Lignin samples were characterized by measuring their ash content, hydroxyl content (Phosphorus Nuclear Magnetic Resonance Spectroscopy), impurities (Inductively Coupled Plasma), and pH. After foam formulation, properties of lignin-based foams were evaluated and compared with a control foam (with no lignin) via cell morphology, closed-cell content, compression strength, apparent density, thermal conductivity, and color analysis. Lignin-based foams passed all measured standard specifications required by ASTM International C1029-15 for type 1 rigid insulation foams, except for three foams. These three foams had poor compressive strengths, significantly larger cell sizes, darker color, lower closed-cell contents, and slower foaming times. The foam made with corn stover enzymatic hydrolysis lignin showed no significant difference from the control foam in terms of compressive strength and outperformed all other lignin-based foams due to its higher aliphatic and p-hydroxyphenyl hydroxyl contents. Lignin-based foams that passed all required performance testing were made with lignins having higher pH, potassium, sodium, calcium, magnesium, and aliphatic/p-hydroxyphenyl hydroxyl group contents than those that failed.     

Analysis of protective action of ischemic preconditioning from fluorescence spectra of blood serum and probes added to it

The protective effect of ischemic preconditioning on brain tissue during total ischemia is shown by using spectral-luminescence methods for estimating oxidative damage to blood components after ischemia. Fluorescence of blood serum and molecular probes added to it is investigated after producing brain ischemia with preconditioning. Lipid free-radical peroxide damage of low-density lipoproteins is found to decrease after producing ischemia with preconditioning rather than ischemia without preconditioning. __________ Translated from Zhurnal Prikladnoi Spektroskopii Vol. 74, No. 3, pp. 378–381, May–June, 2007.