Effect of chemical parameters on pyrene degradation in soil in a pulsed discharge plasma system

Degradation of pyrene in soil in a net-to-net pulsed discharge plasma (PDP) system was reviewed. Effect of main chemical parameters, including air flow rate, pyrene concentration, initial pH and soil moisture content on pyrene degradation was examined. The obtained results show that 87.9% of pyrene could be removed under the condition of 60 min reaction; increasing of air flow rate within 1 L min⁻¹ was favorable for degradation; pyrene removal was decreased with the increase of initial pyrene concentration; oxidation of pyrene was more evident in acidic soil; enhancement of soil moisture content has no benefit on pyrene degradation.     

Elongating the area of plasma/fluid interaction of surface nanosecond pulsed discharges

Plasma-assisted flow control is of high industrial interest, but practical applications at full scale require a large surface of interaction. Nanosecond pulsed Dielectric Barrier Discharge (DBD) have demonstrated promising results of flow control, but their interacting region is limited to only a few cm². In this paper, the conditions to extend a surface nanosecond DBD are documented. It is shown that a sliding discharge regime can fully fill an inter-electrode distance of 40 mm. This discharge regime promotes the formation of two hemispheric pressure waves originating from both air-exposed electrodes while an horizontal region of pressure gradient is also observed.     

Polytetrafluoroethylene and metal structure convective-flow CO laser

A convective flow CO laser composed of polytetrafluoroethylene discharge tubes, nickel–chromium steel components, a cupric heat exchanger and other components is described. Operating in liquid nitrogen condition, output power of 60 W has been obtained from a non-selective cavity.     

Smoothing estimation of rate function for recurrent event data with informative censoring

This paper proposes kernel estimation of the occurrence rate function for recurrent event data with informative censoring. An informative censoring model is considered with assumptions made on the joint distribution of the recurrent event process and the censoring time without modeling the censoring distribution. Under the validity of the informative censoring model, we also show that an estimator based on the assumption of independent censoring becomes inappropriate and is generally asymptotically biased. To investigate the asymptotic properties of the proposed estimator, the explicit form of its asymptotic mean squared risk and the asymptotic normality are derived. Meanwhile, the empirical consistent smoothing estimator for the variance function of the estimator is suggested. The performance of the estimators are also studied through Monte Carlo simulations. An epidemiological example of intravenous drug user data is used to show the influence of informative censoring in the estimation of the occurrence rate functions for inpatient cares over time.     

Photorefractive Four-Wave Mixing Switches Utilizing Pockels Effect -Longitudinal and Lateral Switches-

We carried out detailed calculations for photorefractive wave-mixing switches based on one of three crystals with high electro-optic coefficients, namely, BaTiO₃, Strontium Barium Niobate (SBN (0.75)), and Potasium Sodium Strontium Barium Niobate (KNSBN). A comparison of results for the three crystals shows that a 0_-cut BaTiO³ crystal is suitable for a longitudinal switch and requires a voltage of about 80 for a 2-mm-thick crystal to induce sufficient phase mismatch. The electrodes must be transparent for the incident and diffracted beams. A 45_-cut SBN (0.75) crystal, however, is suitable for a lateral switch and requires a voltage of about 150 for a 1-mm-wide crystal. The electrodes do not need to be transparent.     

采用空心阴极放电等离子体化学气相沉积方法制备a-CH薄膜

 研究了不同衬底-阴极距离、直流电压和H₂流量对a-CH薄膜沉积速率的影响。结果表明：衬底-阴极距离必须大于0.5cm，随着该距离的增加，薄膜的沉积速率减少；直流电压达550V时沉积速率最大；随着H2含量的增加，CH₄含量相对减少，沉积速率随之降低。用AFM观察了以该方法制得的448.4nm CH薄膜的表面形貌，表面粗糙度约为10nm。最后测出了不同条件下CH薄膜的UV-VIS谱，由此可以计算得到薄膜的禁带宽度及折射率。     

Analysis of semiconducting materials by high-resolution radiofrequency glow discharge mass spectrometry

The analytical capabilities of a high-resolution mass spectrometer in combination with a 13.56 MHz glow discharge ion source for the analysis of semiconducting materials (silicon carbide and gallium arsenide) were studied. It was shown that single positively charged ions of sample material have about 10 eV higher average energy than the ions of the discharge and residual gas. Therefore effective energy separation of the ions of analyte from the ions of the discharge and residual gas was achieved by adjusting the ion transfer optics (breadth and position of energy slit), which improves the analytical capabilities of the developed method.Some analytical applications are presented to illustrate the performance of r.f. GDMS for the bulk analysis of semiconducting materials. The results of the trace element analysis of gallium arsenide and silicon carbide samples are compared with data of independent methods (LIMS, ICP-AES, SIMS).Dedicated to Professor Dr. rer. nat. Dr. h.c. Hubertus Nickel on the occasion of his 65th birthdayOn leave from the Institute of Inorganic Chemistry, 630090 Novosibirsk, Russia     

不连续双斜向内肋管纵向涡流动显示

利用染色线流动显示方法,显示并分析了不同雷诺数下不连续双斜向内肋管管内流场。流动显示实验结果表明不连续双斜向内肋管管内存在较强的贴近壁面的纵向涡,纵向涡沿流向可持续约一倍管径距离,并且纵向涡的强度随雷诺数的增加而增强。     

Towards cooling of high-intensity ion beams

Buffer gas beam coolers may become excellent beam preparation devices for high-resolution mass separation. The small beam emittance provided makes efficient isobar resolution a realistic goal. In order to fulfill the needs of future facilities providing high-intensity beams of rare isotopes, it is desirable to increase the beam intensity limit of such devices from typically several tens of nanoamperes to microamperes. This requires the usage of high-voltage radiofrequencies in a low-pressure gas environment. A buffer gas beam cooler, dedicated to this purpose, is under development at the NSCL. The study of voltage breakdowns under such conditions and the design of an electrode system minimizing them is mandatory.      

Preparation and electrical characterization of (PVC + KBrO3) polymer electrolytes for solid state battery applications

This paper presents results of studies on dc electrical conductivity and transference number measurements on potassium bromate (KBrO₃) complexed polyvinyl chloride (PVC) films prepared by solution cast technique. Temperature dependence of dc electrical conductivity and transference number data indicated the dominance of ion type charge transport in these specimens. The magnitude of conductivity increased with increase in concentration of the salt and temperature. Using this (PVC + KBrO₃) electrolyte, solid-state electrochemical cells were fabricated, and their discharge profiles were studied under a constant load of 100 kΩ. Several cell profiles such as open circuit voltage, short circuit current, power density, and energy density associated with these cells were evaluated and were reported. The features of complexation of the electrolytes were studied by X-ray diffraction and Fourier transform infrared spectroscopy. Paper presented at the Third International Conference on Ionic Devices (ICID 2006), Chennai, Tamilnadu, India, Dec. 7–9, 2006