高反射率p-GaN欧姆接触电极

根据光学薄膜原理计算了GaN/Ti/Ag、GaN/Al和GaN/Ni/Au/Ti/Ag、GaN/Ni/Au/Al多层电极结构的反射率,得出Ag基和Al基反射电极均能在全角范围内提供较高的反射率。实验测量结果表明,反射率能高于80%的Ag基反射电极,具有低欧姆接触的电学特性。并将GaN/Ni/Au/Ti/Ag多层反射电极应用在上下电极结构的GaN基LED中。实验上采用两步合金法获得了低接触电阻、高反射率的电极结构,并引入Ni/Au覆盖层克服了Ag高温时的团聚和氧化现象。解决了Ag电极的稳定性问题,显著地提高了LED的出光效率,成功制备了具有上下电极结构的GaN基LED管芯。     

Polydisperse effects in jet spray flames

A laminar jet polydisperse spray diffusion flame is analysed mathematically for the first time using an extension of classical similarity solutions for gaseous jet flames. The analysis enables a comparison to be drawn between conditions for flame stability or flame blow-out for purely gaseous flames and for spray flames. It is found that, in contrast to the Schmidt number criteria relevant to gas flames, droplet size and initial spray polydispersity play a critical role in determining potential flame scenarios. Some qualitative agreement for lift-off height is found when comparing predictions of the theory and sparse independent experimental evidence from the literature.     

晶圆键合和激光剥离工艺对GaN基垂直结构发光二极管芯片残余应力的影响

GaN基发光二极管(LED)中的残余应力状态对器件的性能和稳定性有很大影响. 通过使用三种不同的键合衬底(Al₂O₃衬底, CuW衬底和Si衬底)以及改变键合温度(290 ℃, 320 ℃, 350 ℃和380 ℃), 并且使用不同的激光能量密度(875, 945和1015 mJ·cm^-2) 进行激光剥离, 制备了不同应力状态的GaN基LED器件. 对不同条件下GaN LED进行弯曲度、Raman 散射谱测试. 实验结果表明, 垂直结构LED中的残余应力的状态是键合衬底和键合金属共同作用的结果, 而键合温度影响着垂直结构LED中的残余应力的大小. 激光剥离过程中, 一定能量密度下激光剥离工艺一般不会对芯片中的残余应力造成影响, 但是如果该工艺对GaN 层造成了微裂缝, 则会在一定程度上起到释放残余应力的作用. 使用Si衬底键合后, 外延蓝宝石衬底翘曲变大, 对应制备的GaN基垂直结构 LED中的残余应力为张应力, 并且随着键合温度的上升而变大; 而Al₂O₃和CuW衬底制备的LED中的残余应力为压应力, 但使用Al₂O₃衬底键合制备的LED中压应力随键合温度上升而一定程度变大, CuW 衬底制备的LED中压应力随键合温度上升而下降.     

Surface and Gradiometer Coils near a Conducting Body: The Lift-off Effect

The use of surface coils in magnetic resonance is widespread. Examples include MRI, detection of subsurface aquifers by NMR, and, more recently, landmine detection by nuclear quadrupole resonance. In many of these cases a finite-sized sample to be examined is contained within a larger medium that is a poor electrical conductor, and eddy currents induced by the RF fields provide a loss mechanism that reduces the effective quality factorQof the transmitter and receiver coils. Here the losses induced in a circular surface coil (a horizontal loop antenna) separated a distance from a dissipative medium are calculated and compared to measurements. It is shown that often the overall efficiency of the coil for magnetic resonance can be improved by displacing the coil away from the conducting medium a prescribed “lift-off” distance. The use of a gradiometer as a surface coil is also examined, and it is shown by theory and experiment that in certain circumstances such a gradiometer can be more efficient than a conventional surface coil for inspection of conducting media.     

Transported PDF simulation of auto-ignition of a turbulent methane jet in a hot,vitiated coflow

In the current work, the auto-ignition of a turbulent round methane jet is studied numerically by means of a transported probability density function (PDF) method. The methane jet is issued into a hot, vitiated coflow, where it ignites to form a steady lifted flame. For this flame, experimental data of hydroxyl, temperature and mixture fraction are provided in the area where the fuel auto-ignites. To model this experiment, the transport equation for the thermochemical PDF is solved using a hybrid finite volume / Lagrangian Monte-Carlo method. Turbulence is modelled using the k-? turbulence model including a jet-correction. Computational results are compared to experimental data in terms of mean quantities, variances and lift-off height. Moreover, the structure of the one-point, one-time marginal PDF of temperature is analysed and compared to experimental data which are provided in this work. It is found that the transported PDF method in conjunction with the k-? model is capable of reproducing these statistical data very well. In particular the effect of ignition on the marginal PDF of temperature can be well reproduced with this approach. To further analyse the relevant processes in the evolution of the temperature PDF, a statistically homogeneous system is studied both numerically and analytically.     

Fabrication and analysis of thin-film GaAs solar cell on flexible thermoplastic substrate using a low-pressure cold-welding

We present flexible thin-film GaAs solar cells fabricated on thermoplastic substrates by a low-pressure cold-welding and epitaxial lift-off process. The use of polyethylene terephthalate (PET) film as a flexible substrate enables cold welding (130 °C) of gold layers between a thin-film GaAs solar cell and PET film with very low mechanical pressure (0.4 MPa), due to their thermoplastic properties. The feasibility of the proposed technique was demonstrated by fabricating GaAs single junction solar cells (without antireflection coating) on PET film, having an efficiency of 13.2%. The fabricated solar cell also showed a stable performance after 2000 cycles of bending.     

火焰周边扰流脱火效能的图像分析技术

 脱火现象的分析研究是喷射火灾脱火法施救等诸多技术的重要基础。论文提出并较为深入地研究了火焰周边扰动气流脱火效能的图像分析技术。详细阐述了技术思想,分析了图像的获取及其信息的处理过程,建立了求解表征扰流脱火效能的火焰脱开距离数学模型,并通过专门设计的实验,初步验证了这一分析技术的可行性,为脱火现象的分析研究提供了重要的技术基础。     

Integration of GaN thin films to SiO2–Si(100) substrates by laser lift-off and wafer fusion method

A process methodology has been adopted to bond GaN thin films to Si(100) substrates using the combination of laser lift-off and direct wafer fusion. Using optimum excimer laser conditions, 2–10 μm of GaN is lifted-off from sapphire. The lifted-off thin film is cleared from gallium residual and then suitably treated in a hydrofluoric, nitric and acetic acid mixture to render the surface hydrophilic. This treatment provides van der Waals bonds to immediately contact bond with SiO₂–Si(100) substrate at room temperature. The bonds are further strengthened by a high temperature annealing at 650 C for 2 h. The structural and mechanical characteristics of the bonded structure reveal uniform and high quality bonding. The optical characteristics of the transferred bonded film on SiO₂–Si(100) substrate exhibit similar properties to that of GaN on sapphire. In a similar manner, high-brightness blue LEDs were transferred from sapphire to SiO₂–Si(100) substrate with no deterioration in the electrical and optical performance of the device.     

Curved two-dimensional electron gases

A method is introduced which makes it possible to fabricate non-planar two-dimensional electron gases. Making use of the “epitaxial lift-off” process, patterned, gated and contacted heterostructures are transferred from their crystalline substrate onto small glass tubes with diameters of a few millimeters. The transport properties of two-dimensional electron gases inside these curved semiconductor films are characterized by low-temperature magnetoresistance measurements. In the longitudinal resistance we find weak Shubnikov–de Haas oscillations, which are periodic in B⁻¹. The transverse resistance exhibits well-developed quantum Hall plateaus at low magnetic fields. At high fields, we observe a pronounced breakdown of the Hall effect. The experimental results are compared with simple theoretical models.     

Numerical study of transient evolution of lifted jet flames: partially premixed flame propagation and influence of physical dimensions

Three-dimensional (3D) unsteady Reynolds-averaged Navier–Stokes simulations of a spark-ignited turbulent methane/air jet flame evolving from ignition to stabilisation are conducted for different jet velocities. A partially premixed combustion model is used involving a correlated joint probability density function and both premixed and non-premixed combustion mode contributions. The 3D simulation results for the temporal evolution of the flame's leading edge are compared with previous two-dimensional (2D) results and experimental data. The comparison shows that the final stabilised flame lift-off height is well predicted by both 2D and 3D computations. However, the transient evolution of the flame's leading edge computed from 3D simulation agrees reasonably well with experiment, whereas evident discrepancies were found in the previous 2D study. This difference suggests that the third physical dimension plays an important role during the flame transient evolution process. The flame brush's leading edge displacement speed resulting from reaction, normal and tangential diffusion processes are studied at different typical stages after ignition in order to understand the effect of the third physical dimension further. Substantial differences are found for the reaction and normal diffusion components between 2D and 3D simulations especially in the initial propagation stage. The evolution of reaction progress variable scalar gradients and its interaction with the flow and mixing field in the 3D physical space have an important effect on the flame's leading edge propagation.