Human-to-metal electrostatic discharge current measurements – Notes on the ESD current waveform

The Electrostatic Discharge (ESD) phenomenon has been described through the IEC 61000-4-2. ESD current parameters' values, have been set in this Standard. The theoretical ESD current waveform defined in this standard, describing the conventional Contact discharge mode, needs to be re-evaluated on the basis of accurate experimental data. Even though the standard deals with commercial ESD generators, its goal is to simulate the natural phenomenon as good as possible. More and accurate data may contribute to the better simulation of the natural phenomenon. New values and better comprehension of the phenomenon demand new measurements based on high end measuring equipment. Such works and publications have been carried out the past years. Yet, the need to systematize and integrate this work remains. Larger and trust-worthy series of measurements need to be carried out and presented clearly.This paper deals with new ESD-current data, taken with broadband equipment. New and more detailed measurements like these, were never before taken at such a large number of individuals. The goal of this work is that the data acquired can serve as a basis for re-evaluating the conventional approach of the scientific community to the ESD event.In this paper, using a broadband measuring system, new parameters' values are measured and relations are presented, following standard statistical procedures. The results, which occur from measurements carried out on tenths of human individuals, are questioning the Standard in many points. A new way of approaching the standardization of the ESD current is proposed, as the excuse of the poor measuring equipment that sets barriers on the measuring accuracy, does not apply any more. The charging voltages of 500 V and 1000 V were also examined since such range of voltages are often met at ESD events and they are considered very harmful.     

The mechanism of ethylene polymerization by nickel salicylaldiminato catalysts - Agostic interactions and their kinetic isotope effects

The ethylene polymerization reaction of a neutral nickel catalyst was studied by DFT calculations at the Becke3LYP/6-31G(d) level of theory. As in related cases a β-agostic bond stabilizes the nickel alkyl ground states. Transition states for the insertion of the olefin show a distinct α-agostic interaction, which has not been observed for late metal polymerization catalysts before. An ethylene-alkyl complex was identified as the resting state of the reaction. The overall barrier height of the reaction amounts to 17.54 kcal/mol, which slightly increases to 17.60 kcal/mol for the polymerization of deuterated ethylene. Therefore, a small positive kinetic isotope effect (k_H/k_D = 1.09) can be calculated, which is caused by the α-agostic interaction in the transition state. A comparison to other late metal based polymerization systems reveals that the ethylene coordination step of highly active catalysts is significantly lower in energy compared to catalysts which are only moderately active.     

A novel approach to the acoustic characterisation of porous road surfaces

Porous road surfaces offer an effective means of reducing the generation and propagation of noise from road traffic. However, the porosity of these surfaces can deteriorate over time, leading to a reduction in their noise reducing properties. Efficient methods are therefore required for monitoring this performance. Existing techniques for performing in-situ measurements of acoustic absorption are unsuitable for use within the traffic stream. Static measurements using time domain Maximum Length Sequence (MLS) based techniques have been demonstrated to offer advantages over traditional techniques, presenting the opportunity for measurements under dynamic conditions. This paper describes the design of a system for carrying out dynamic MLS-based measurements. Results are presented which demonstrate that stable dynamic measurements can be carried out at speeds of up to 30 km/h.     

Investigations of low- and high-spin states of <Superscript>132</Superscript>La

The fusion evaporation reaction ¹²²Sn(¹⁴N, 4n)¹³²La was used to populate the high-spin states of ¹³²La at the beam energy of 60 MeV. A new band consisting of mostly E2 transitions has been discovered. This band has the interesting links to the ground state 2^- and the isomeric state 6^-. A new transition of energy 351 keV connecting the low-spin states of the positive-parity band based on the πh _11/2 ⊗ νh _11/2 particle configuration, has been found. This has played a very important role in resolving the existing ambiguities and inconsistencies in the spin assignment of the band head. Received: 12 August 2002 / Accepted: 18 March 2003 / Published online: 7 May 2003     

Optimal entropic uncertainty relation for successive measurements in quantum information theory

We derive an optimal bound on the sum of entropic uncertainties of two or more observables when they are sequentially measured on the same ensemble of systems. This optimal bound is shown to be greater than or equal to the bounds derived in the literature on the sum of entropie uncertainties of two observables which are measured on distinct but identically prepared ensembles of systems. In the case of a two-dimensional Hilbert space, the optimum bound for successive measurements of two-spin components, is seen to be strictly greater than the optimal bound for the case when they are measured on distinct ensembles, except when the spin components are mutually parallel or perpendicular     

On practical metrology and chemical analysis: etalons and traceability systems

 National measurement systems are infrastructures to ensure, for each nation, a consistent and internationally recognised basis for measurement. Such complex systems have historical, technical, legal, organisational and institutional aspects to connect scientific metrology with practical measurements. Underlying any valid measurement is a chain of comparisons linking the measurement to an accepted standard. The ways the links are forged and the etalons (measurement standards) to which they connect are defining characteristics of all measurement systems. This is often referred to as traceability which aims at basing measurements in common measurement units – a key issue for the integration of quantitative chemical analysis with the evolving physical and engineering measurement systems. Adequate traceability and metrological control make possible new technical capabilities and new levels of quality assurance and confidence by users in the accuracy and integrity of quantitative analytical results. Traceability for chemical measurements is difficult to achieve and harder to demonstrate. The supply of appropriate etalons is critical to the development of metrology systems for chemical analysis. An approach is suggested that involves the development of networks of specialised reference laboratories able to make matrix-independent reference measurements on submitted samples, which may then be used as reference materials by an originating laboratory using its practical measurement procedures. Received: 31 July 1995 Accepted: 19 August 1995     

High temperature annealing effect on structural and magnetic properties of Ti/Ni multilayers

High temperature annealing effect on structural and magnetic properties of Ti/Ni multilayer (ML) up to 600 °C have been studied and reported in this paper. Ti/Ni multilayer samples having constant layer thicknesses of 50 Å each are deposited on float glass and Si(1 1 1) substrates using electron-beam evaporation technique under ultra-high vacuum (UHV) conditions at room temperatures. The micro-structural parameters and their evolution with temperature for as-deposited as well as annealed multilayer samples up to 600 °C in a step of 100 °C for 1 h are determined by using X-ray diffraction (XRD) and grazing incidence X-ray reflectivity techniques. The X-ray diffraction pattern recorded at 300 °C annealed multilayer sample shows interesting structural transformation (from crystalline to amorphous) because of the solid-state reaction (SSR) and subsequent re-crystallization at higher temperatures of annealing, particularly at ≥400 °C due to the formation of TiNi₃ and Ti₂Ni alloy phases. Sample quality and surface morphology are examined by using atomic force microscopy (AFM) technique for both as-deposited as well as annealed multilayer samples. In addition to this, a temperature dependent dc resistivity measurement is also used to study the structural transformation and subsequent alloy phase formation due to annealing treatment. The corresponding magnetization behavior of multilayer samples after each stage of annealing has been investigated by using Magneto-Optical Kerr Effect (MOKE) technique and results are interpreted in terms of observed micro-structural changes.     

Synthesis and characterization of isotopically enriched methylmercury (CH3201Hg+)

A simple procedure for the synthesis of an important standard, isotopically enriched methylmercury, which is not commercially available, has been established successfully. The isotopically enriched standard synthesized is utilized in conventional isotope dilution mass spectrometry (IDMS), as well as in speciated IDMS (SIDMS), for determination of the true concentration of methylmercury in environmental samples. The CH₃²⁰¹Hg⁺ standard has been synthesized from commercially available ²⁰¹HgO and tetramethyltin. The synthesis time required is 1 h at 60°C. The product is highly pure, yielding more than 90% as ²⁰¹Hg in CH₃²⁰¹Hg⁺. Hazardous dimethylmercury does not occur during this synthesis procedure. The product synthesized was analyzed using high‐performance liquid chromatography coupled with inductively coupled plasma mass spectrometry (ICP‐MS) and ICP‐MS alone in order to determine its concentration, isotopic composition and purity. The stability of the product was also evaluated for over 6 months and found to be stable at 4°C in the dark. The isotopically enriched methylmercury synthesized can be used in SIDMS and IDMS analyses as a standard. Copyright © 2003 John Wiley & Sons, Ltd.     

Quantitative evaluation of two-dimensional dynamic deformations using digital holography

An optical system for the parallel evaluation of in- and out-of-plane dynamical deformations will be described. A double pulse laser with pulse separation in the microsecond range is used for the investigations. Two separate interferograms of an object under test, in its undeformed and deformed state, are recorded in a few microseconds. The object is illuminated from two different directions and imaged onto a CCD sensor. This produces two sensitivity vectors. The reference beams have different directions in order to produce two directional spatial carriers. The Fourier method is used for quantitative evaluation, and the measurements along different sensitivity vectors are separated in the Fourier domain. The phases of the two interferograms are obtained from the complex amplitudes and the two dimensional deformation is calculated from the phases. Experimental results are presented.     

A high-current electron beam ion trap as an on-line charge breeder for the high precision mass measurement TITAN experiment

The precision of atomic mass measurements in a Penning trap is directly proportional to the charge state q of the ion and, hence, can be increased by using highly charged ions (HCI). For this reason, charge breeding with an electron beam ion trap (EBIT) is employed at TRIUMF’s Ion Trap for Atomic and Nuclear science (TITAN) on-line facility in Vancouver, Canada. By bombarding the injected and trapped singly charged ions with an intense beam of electrons, the charge state of the ions is rapidly increased inside the EBIT. To be compatible with the on-line requirements of short-lived isotopes, very high electron beam current densities are needed. The TITAN EBIT includes a 6 Tesla superconducting magnet and is designed to have electron beam currents and energies of up to 5 A and 60 keV, respectively. Once operational at full capacity, most species can be bred into a He-like configuration within tens of ms. Subsequently, the HCI are extracted, pass a Wien filter to reduce isobaric contamination, are cooled, and injected into a precision Penning trap for mass measurement. We will present the first results and current status of the TITAN EBIT, which has recently been moved to TRIUMF after assembly and commissioning at the Max-Planck-Institute (MPI) for Nuclear Physics in Heidelberg, Germany.