HIRFL–CSR加速器中束流与真空中剩余气体的碰撞损失

研究了重离子加速器中束流与真空中剩余气体的碰撞损失过程和碰撞截面,在依据大量实验数据的基础上,提出了一组计算离子一原子的电荷交换截面的经验公式.以兰州重离子加速器HDRFL及冷却储存环CSR为例,给出了依据碰撞截面的公式计算束流在加速器真空中的传输效率的方法,并计算了在不同真空度下HIRFL的ECR源轴向注入束运线、注入器SFC、前束运线、主加速器SSC和后束运线等不同加速阶段及CSR的传输效率,并提出合理的真空度要求.HIRFL的真空分布测量和束流的损失测量证明了该计算方法的可靠性.     

Surfaces of Constant Mean Curvature Bounded by Two Planar Curves

In this paper we study constant mean curvature compact surfaces with two Jordan curves in parallel planes as boundary and we investigate the point at which the surface inherits the symmetries of its boundary.     

355nm Nd∶YAG激光在H_2中的高效一级斯托克斯转换

对脉冲Nd∶YAG激光(355 nm)在H2和H2∶He-Ar混合气体中的受激拉曼散射(SRS)进行了研究。在0.5 MPa的氢气中,同时测量到从二级反斯托克斯到三级斯托克斯的多波长输出,其总转化效率达88%;而高压下只剩下一级和二级斯托克斯输出,其中二级斯托克斯最大能量转化效率达44%(对应量子效率为63%)。由于高级斯托克斯的竞争,纯氢气中一级斯托克斯的最大能量转换效率不超过43%。通过向3 MPa氢气中掺入2 MPaAr气后,很好地抑制了二级斯托克斯的产生,从而获得了能量转换效率高达71%(对应量子效率为83%)的一级斯托克斯输出。对四波混频和级联受激拉曼散射在氢气多级斯托克斯产生中的作用以及惰性气体对它们的影响进行了讨论。     

曲轴箱窜气量检测仪的研制

介绍了车用压差式气体流量传感器的结构设计和电测电路，指出了传感器的使用范围，由实验测出了特性曲线．该仪器可检测车用发动机曲轴箱窜气量，适用于发动机不解体故障诊断．     

ISLAND—Inverse Square Law Acceleration Measurement Using iNertial Drift

By using a novel free-flying, rotating, optical bench aboard the International Space Station (ISS) as the basis for a measurement of differential acceleration between two gravitating bodies, in principle the Newtonian inverse-square law and the constant of gravitation, G, can be determined at the parts in 10⁶ level.     

A novel tridentate nitrogen donor as ligand in copper catalyzed ATRP of methyl methacrylate

A tridentate ligand, BPIEP: 2,6‐bis[1‐(2,6‐diisopropyl phenylimino) ethyl] pyridine, having central pyridine unit and two peripheral imine coordination sites was effectively employed in controlled/“living” radical polymerization of MMA at 90°C in toluene as solvent, Cu^IBr as catalyst, and ethyl‐2‐bromoisobutyrate (EBiB) as initiator resulting in well‐defined polymers with polydispersities M_w/M_n ≤ 1.23. The rate of polymerization follows first‐order kinetics, k_app = 3.4 × 10^?5 s^?1, indicating the presence of low radical concentration ([P*] ≤ 10^?8) throughout the reaction. The polymerization rate attains a maximum at a ligand‐to‐metal ratio of 2:1 in toluene at 90°C. The solvent concentration (v/v, with respect to monomer) has a significant effect on the polymerization kinetics. The polymerization is faster in polar solvents like, diphenylether, and anisole, as compared to toluene. Increasing the monomer concentration in toluene resulted in a better control of polymerization. The molecular weights (M_n,SEC) increased linearly with conversion and were found to be higher than predicted molecular (M_n,Cal). However, the polydispersity remained narrow, i.e., ≤1.23. The initiator efficiency at lower monomer concentration approaches a value of 0.7 in 110 min as compared to 0.5 in 330 min at higher monomer concentration. The aging of the copper salt complexed with BPIEP had a beneficial effect and resulted in polymers with narrow polydispersitities and higher conversion. PMMA obtained at room temperature in toluene (33%, v/v) gave PDI of 1.22 (M_n = 8500) in 48 h whereas, at 50°C the PDI is 1.18 (M_n = 10,300), which is achieved in 23 h. The plot of lnk_app versus 1/T gave an apparent activation energy of polymerization as (ΔE^≠_app) 58.29 KJ/mol and enthalpy of equilibrium (ΔH⁰_eq) to 28.8 KJ/mol. Reverse ATRP of MMA was successfully performed using AIBN in bulk as well as solution. The controlled nature of the polymerization reaction was established through kinetic studies and chain extension experiments. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4996–5008, 2005     

毛细管气相色谱法测定中药中有机氯农药残留量

建立了江西省两种中药中有机氯农药残留量的气相色谱分析方法。样品以丙酮提取,在NaCl存在下,以正已烷进行液—液分配,提取液用H2SO4净化,采用DB—1701毛细管柱,GC—ECD检测有机氯农药残留量。最低检测限为1.0×10-3-5.0×10-3mg/kg,添加回收率为85.7%-115.2%,应用于实际样品中有机氯农药残留量的检测,获得了较为满意结果。     

Conformal Invariance, Accelerating Universe and the Cosmological Constant Problem

We investigate a conformal invariant gravitational model which is taken to hold at early universe. The conformal invariance allows us to make a dynamical distinction between the two unit systems (or conformal frames) usually used in cosmology and elementary particle physics. In this model we argue that when the universe suffers phase transition, the resulting mass scale introduced by particle physics should have a variable contribution to vacuum energy density. This variation is controlled by the conformal factor which is taken as a dynamical field. We then deal with the cosmological consequences of this model. In particular, we shall show that there is an inationary phase at early times. At late times, on the other hand, it provides a mechanism which makes a large effective cosmological constant relax to a sufficiently small value. Moreover, we shall show that the conformal factor acts as a quintessence field that leads the universe to accelerate at late times.     

Dependence of the kinetics of the anionic polymerization of methyl methacrylate on the concentration in active centers

Studies on the anionic polymerization of methyl methacrylate in tetrahydrofuran and in the presence of sparteine have revealed a beneficial effect due to this additive, resulting in a decrease in the extent of termination. Better control of the definition of the polymers formed can thus be achieved in the presence of this additive. On the other hand, macromolecular engineering requires a range of active species concentrations lower than 10^?3 mol L^?1 and particularly the synthesis of polymers of high molar masses. For a better understanding of the mechanism of chain growth under such concentration conditions, the kinetics of polymerization have been investigated with a technique based on adiabatic calorimetry. Sparteine has been found to lack sufficient cation‐binding power to prevent the propagating enolate ion pairs from aggregating. The rate constant of propagation of nonaggregated species has been estimated, as well as the aggregation constant of equilibrium. For very low initiator concentrations, termination reactions have been shown to profoundly alter the control of the polymerization and to prevent a quantitative monomer conversion. Theoretical maximal conversions have been calculated from kinetic data and compare well with the experimental values. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4964–4975, 2004     

Permeability of N2, Ar,He, O2, and CO2 through as‐extruded amorphous and biaxially oriented polyester films: Dependence on chain mobility

For as‐extruded amorphous and biaxially orientated polyester films based on poly(ethylene terephthalate), poly(ethylene naphthalate), and copolymers containing poly(ethylene terephthalate) and poly(ethylene naphthalate) moieties, permeability, diffusion, and solubility coefficients are interpreted in terms of chain mobility. The influence of polymer morphology is determined by comparison of the data for as‐extruded amorphous sheets and materials produced with different biaxial draw ratios. The crystallinities of the samples were assessed using differential scanning calorimetry and density measurements. Changes in mobility at a molecular level were investigated using dielectric spectroscopy and dynamic mechanical thermal analysis. The study, in conjunction with our earlier work, leads to the conclusion that the key to understanding differences in gas transport is the difference in local chain motions rather than in free volume. This was illustrated by the permeability results for He, Ar, N₂, and O₂ in the range of polyesters. However, the permeability of CO₂ was found to require alternative explanations because of polymer–penetrant interactions. For biaxially oriented samples, the differences in diffusivity are not only due to differences in local chain motions, but also additional constraints resulting from the increased crystallinity and chain rigidity—which also act to hinder segmental mobility. The effectiveness of the reduction in permeability in the biaxially oriented films is consequently determined by the ability of the polymer chains to effectively align and form crystalline structures. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2916–2929, 2004