Human-to-metal electrostatic discharge current measurements – Notes on the ESD current waveform

The Electrostatic Discharge (ESD) phenomenon has been described through the IEC 61000-4-2. ESD current parameters' values, have been set in this Standard. The theoretical ESD current waveform defined in this standard, describing the conventional Contact discharge mode, needs to be re-evaluated on the basis of accurate experimental data. Even though the standard deals with commercial ESD generators, its goal is to simulate the natural phenomenon as good as possible. More and accurate data may contribute to the better simulation of the natural phenomenon. New values and better comprehension of the phenomenon demand new measurements based on high end measuring equipment. Such works and publications have been carried out the past years. Yet, the need to systematize and integrate this work remains. Larger and trust-worthy series of measurements need to be carried out and presented clearly.This paper deals with new ESD-current data, taken with broadband equipment. New and more detailed measurements like these, were never before taken at such a large number of individuals. The goal of this work is that the data acquired can serve as a basis for re-evaluating the conventional approach of the scientific community to the ESD event.In this paper, using a broadband measuring system, new parameters' values are measured and relations are presented, following standard statistical procedures. The results, which occur from measurements carried out on tenths of human individuals, are questioning the Standard in many points. A new way of approaching the standardization of the ESD current is proposed, as the excuse of the poor measuring equipment that sets barriers on the measuring accuracy, does not apply any more. The charging voltages of 500 V and 1000 V were also examined since such range of voltages are often met at ESD events and they are considered very harmful.     

用等厚干涉测定液体折射率

介绍一种采用等厚干涉原理测定液体折射率的简单可靠的方法。     

计算全息检测非球面干涉场的理论分析与实验结果

本文应用光学全息术及傅里叶光学的理论对计算全息图干涉检测非球面面形的光路及干涉场进行了理论分析,提出了其干涉场为不定域干涉的观点,并在实验中予以证实.     

迈克尔逊干涉仪中补偿板与干涉条纹

通过分析缺失补偿板的迈克尔逊干涉仪中的附加光程差,推出干涉条纹满足的方程式,并用计算机模拟了动镜移动过程中变化的干涉条纹,与实验结果相一致.     

来自磁光阱中冷原子团的荧光干涉条纹及其应用

实验观察来自磁光阱中冷原子团的荧光经真空系统窗口的平板玻璃反射产生的干涉条纹，理论分析表明从从荧光干涉条纹的强度分布可获得关于俘获原子总数以及密度分布的信息。采用该方法实测了俘获原子总数，并模拟得到了不同密度分布时条纹的对比度变化。     

光纤白光干涉仪等臂长技术研究

介绍了几种光纤干涉仪等臂长技术,比较了各自的优缺点和适用范围,对光纤干涉仪的平衡有较大的参考价值。     

宽带膜厚实时监控过程中膜层折射率的确定方法

为了准确计算出镀膜过程中每层膜的折射率，介绍了实时监控过程中确定膜层折射率的2种方法：一种是由实测的透射比光谱直接反算出膜层的折射率；另一种是用最小二乘法的优化算法实时拟合折射率。试验结果表明：在线反算适合单点监控，所得折射率误差小于2%。然而在实际镀膜过程中,由于宽带内膜层参数误差较大,一般大于25%。为此，采用最小二乘法拟合，即在整个宽光谱范围内采集每个波长点的信息，所得结果误差很小，一般都在2％～5%之间,有时可达到10%,在很大程度上提高了实际镀膜时膜厚监控的精度。     

激光二极管反馈干涉的实验观测

利用LabView软件虚拟示波器和信号源,观测了激光二极管反馈干涉实验现象．实验证明反馈回激光二极管的光的入射方向和入射光强以及信号处理电路的带宽,对反馈干涉信号有很大的影响．     

Experimental observation of quantum corrections to electrical resistivity in nanocrystalline soft magnetic alloys

X-ray diffraction patterns of nanocrystalline Fe-Cu-Nb-Si-B (FINEMET) alloys reveal that bcc α-Fe/α-FeSi crystallites with the average grain size of 20(5) nm are dispersed in amorphous matrix. Enhanced electron—electron interaction (EEI) and quantum interference (QI) effects as well as electron-magnon (and/or electron-spin fluctuation) scattering turn out to be the main mechanisms that govern the temperature dependence of resistivity. Of all the inelastic scattering processes, inelastic electron-phonon scattering is the most effective mechanism to destroy phase coherence of electron wave functions. The diffusion constant, density of states at the Fermi level and the inelastic scattering time have been estimated, for the first time, for the alloys in question Article presented at the International Symposium on Advances in Superconductivity and Magnetism: Materials, Mechanisms and Devices, ASMM2D-2001, 25–28 September 2001, Mangalore, India.     

Laser-induced damage of Ta2O5/SiO2 narrow-band interference filters under different 1064 nm Nd:YAG laser modes

The laser-induced damage (LID) behavior of narrow-band interference filters was investigated with a Nd:YAG laser at 1064 nm under single-pulse mode and free-running mode. The absorption measurement of such coatings was performed with surface thermal lensing (STL) technique. The damage morphologies under the two different laser modes were also studied in detail. It was found that all the filters exhibited a pass-band-center-dependent absorption and laser-induced damage threshold (LIDT) behavior, but the damage morphologies were diverse. The explanation was given with the analysis of the electric field distribution and the operational behavior of the irradiation laser.