Spray Freeze-drying – The Process of Choice for Low Water Soluble Drugs?

Most of the novel highly potent drugs, developed on the basis of modern molecular medicine, taking into account cell surface recognition techniques, show poor water solubility. A chemical modification of the drug substance enhancing the solubility often decreases the pharmacological activity. Thus, as an alternative an increase of the solubility can be obtained by the reduction of the size of the drug particles. Unfortunately, it is often difficult to obtain micro or nanosized drug particles by classical or more advanced crystallization using supercritical gases or by milling techniques. In addition, nanosized particles are often not physically stable and need to be stabilized in an appropriate matrix. Thus, it may be of interest to manufacture directly nanosized drug particles stabilized in an inert hydrophilic matrix, i.e. nanostructured and nanocomposite systems. Solid solutions and solid dispersions represent nanostructured and nanocomposite systems. In this context, the use of the vacuum-fluidized-bed technique for the spray-drying of a low water soluble drug cosolubilized with a hydrophilic excipient in a polar organic solvent is discussed. In order to avoid the use of organic solvents, a special spray-freeze-drying technique working at atmospheric pressure is presented. This process is very suitable for temperature and otherwise sensitive drugs such as pharmaproteins.     

“Slow” active control of combustion instabilities by modification of liquid fuel spray properties

This paper describes an experimental investigation of the feasibility of using “slow” active control approaches, which “instantaneously” change liquid fuel spray properties, to suppress combustion instabilities. The objective of this control approach was to break up the feedback between the combustion process heat release and combustor pressure oscillations that drive the instability by changing the characteristics of the combustion process (e.g., the characteristic combustion time). To demonstrate the feasibility of such control, this study used a proprietary fuel injector (Nanomiser^TM), which can vary its fuel spray properties, to investigate the dependence of acoustics–combustion process coupling, i.e., the driving of combustion instabilities, upon the fuel spray properties. This study showed that by changing the spray characteristics it is possible to significantly damp combustion instabilities. Furthermore, using combustion zone chemiluminescence distributions, which were obtained by Abel’s deconvolution synchronized with measured acoustic data, it has been shown that the instabilities were mostly driven midway between the combustor centerline and wall, a short distance downstream from the flame holder, where the mean axial flow velocity is approximately zero in the vortex near the flame holder. The results of this study strongly suggest that a “slow” active control system that employs controllable fuel injectors could be effectively used to prevent the onset of detrimental combustion instabilities.     

Deposition conditions in tailoring the morphology of highly porous reticular films prepared by electrostatic spray deposition (ESD) technique

Spongy-like reticular structure is a unique morphology fabricated by electrostatic spray deposition (ESD) technique. The effects of solvent, substrate temperature, precursor feeding rate, static electric field strength, and deposition time on tailoring the reticular structure were investigated. Scanning electron microscopy was used to observe the film morphology. MnO_x or LiMn₂O₄ were selected as the model materials. It is found that in addition to the conventional solvent butyl carbitol, other kinds of solvents such as ethylene glycol and propylene glycol can also be used to obtain reticular films at a suitable substrate temperature. Porous films with a low cross-linking degree pore structure can be prepared by increasing precursor feeding rate or decreasing substrate temperature. Increasing the deposition time or the electric field strength helps to obtain reticular films with more homogeneous pore size distribution. In addition, the addition of a high boiling-point solvent in mixed alcohol solvent results in the increase of proper substrate temperature. It is concluded that the fluidity of the spray droplets on the surface of a hot substrate is an important factor to form a reticular film.     

Determination of the boiling point distribution of sulfur compounds in light cycle oil using GC with a flame photometric detector and pyrolyzer

A method has been developed to determine the boiling point distribution of sulfur compounds in light cycle oils (LCO'S). The method chosen for this analysis was GC with a flame photometric detector (FPD) and pyrolyzer. Tests were carried out to evaluate the recovery efficiency, repeatability, and accuracy of the method. Repeatabilities within 2% were obtained. The recovery of benzothiophenes and dibenzothiophenes was close to 100%; this was important because these are the major sulfur components in LCO's. No hydrocarbon or solvent interferences were observed with the use of the pyrolyzer, even for a 95% solvent level. Comparison with results from other techniques showed that the method accurately determined the levels of sulfur compounds in the LCO boiling point range.     

Simultaneous Measurement of Droplet Size and Three-Components of Velocity in Spray

The combination of the optical diagnostics and image processing technique has produced various methods of practical measurement in engineering. The measurement of size and velocity of droplets in fuel spray is one typical example. In general, the spray is a complicated and three-dimensional two-phase flow; therefore multi-dimensional field measurement of the spray field is indispensable. In the present paper, a technique of simultaneous measurement of droplet size and three-components of velocity is proposed and applied to spray issuing from the swirl nozzle as a practical application. The focused image of glare points is captured by a stereoscopic arrangement, and droplet size and the three-components of velocity are evaluated from the doublet image. Fundamental optical arrangements to capture the image of the glare points with a stereo view are established, and the feasibility and the accuracy of the technique are confirmed. © 2004 The Optical Society of Japan     

Correlation between Al2O3 particles and interface of Al-Al2O3 coatings by cold spray

Al-Al₂O₃ composite coatings with different Al₂O₃ particle shapes were prepared on Si and Al substrate by cold spray. The powder compositions of metal (Al) and ceramic (Al₂O₃) having different sizes and agglomerations were varied into ratios of 10:1 wt% and 1:1 wt%. Al₂O₃ particles were successfully incorporated into the soft metal matrix of Al. It was found that crater formation between the coatings and substrate, which is typical characteristic signature of cold spray could be affected by initial starting Al₂O₃ particles. In addition, when the large hard particles of fused Al₂O₃ were employed, the deep and big craters were generated at the interface between coatings and hard substrates. In the case of pure soft metal coating such as Al on hard substrate, it is very hard to get proper adhesion due to lack of crater formation. Therefore, the composite coating would have certain advantages.     

Magnetic properties of lanthanum orthoferrite fine powders prepared by different chemical routes

Fine powders of lanthanum iron oxide, LaFeO₃, have been prepared by solid state reaction as well as sol-gel synthesis and nebulized spray pyrolysis. Structures, morphologies and magnetic susceptibility measurements of these powders have been examined. The powders prepared by all the three low-temperature routes contain nearly spherical particles with an average diameter of 40 nm. These samples show a lower Neel temperature than the powder prepared by solid state reaction besides showing much lower magnetic susceptibility at low temperatures. Dedicated to Professor C N R Rao on his 70th birthday     

热喷涂技术的现状和发展

介绍了热喷涂工艺的特点，喷涂方法的种类及其技术以及热喷涂技术的应用概况，并对热喷涂技术的发展方向给予了展望。     

新型聚丙烯酸酯类柴油降凝剂分子模型的建立及验证

在前期工作得出的正构烷烃含量与浊点、冷滤点、凝点的定量关系模型基础上，选择柴油降凝剂的基团对柴油降凝剂分子结构进行了设计，得出了设计模型。结果表明，将含氮基团引入柴油降凝剂可以显著提高柴油降凝剂的性能。根据设计模型合成了一系列聚丙烯酸单酯和混合酯柴油降凝剂，并通过对柴油降凝剂的性能测试结果和自行设计的计算程序对设计模型进行了验证，结果表明，从柴油正构烷烃含量对柴油降凝剂的配比进行设计是可行的。