Sandwich-like Catalyst–Carbon–Catalyst Trilayer Structure as a Compact 2D Host for Highly Stable Lithium–Sulfur Batteries

Herein, we propose the construction of a sandwich-structured host filled with continuous 2D catalysis–conduction interfaces. This MoN-C-MoN trilayer architecture causes the strong conformal adsorption of S/Li₂S_x and its high-efficiency conversion on the two-sided nitride polar surfaces, which are supplied with high-flux electron transfer from the buried carbon interlayer. The 3D self-assembly of these 2D sandwich structures further reinforces the interconnection of conductive and catalytic networks. The maximized exposure of adsorptive/catalytic planes endows the MoN-C@S electrode with excellent cycling stability and high rate performance even under high S loading and low host surface area. The high conductivity of this trilayer texture does not compromise the capacity retention after the S content is increased. Such a job-synergistic mode between catalytic and conductive functions guarantees the homogeneous deposition of S/Li₂S_x, and avoids thick and devitalized accumulation (electrode passivation) even after high-rate and long-term cycling.     

Recent Advances of Freestanding Cathodes for Li-S Batteries

Lithium-sulfur batteries (LSBs) with high energy density and low cost have been recognized as one of the most promising next-generation energy storage systems. Although it has taken decades of development, the practical application of LSBs has been hindered by several inherent obstacles, particularly the severe shuttle effect and sluggish reaction kinetics in the sulfur cathode. Various strategies have been proposed to address these problems via rational design of electrode materials and configurations. Freestanding sulfur cathode could be a promising strategy to improve the sulfur mass loading at the cathode level and energy density of LSBs. This minireview will briefly summary the recent advances in freestanding cathodes for LSBs. The advantages and disadvantages of various freestanding cathodes are discussed and the prospects for the development of flexible cathodes are envisioned.     

Lithium Insertion Mechanism in Iron-Based Oxyfluorides with Anionic Vacancies Probed by PDF Analysis

The mechanism of lithium insertion that occurs in an iron oxyfluoride sample with a hexagonal–tungsten–bronze (HTB)-type structure was investigated by the pair distribution function. This study reveals that upon lithiation, the HTB framework collapses to yield disordered rutile and rock salt phases followed by a conversion reaction of the fluoride phase toward lithium fluoride and nanometer-sized metallic iron. The occurrence of anionic vacancies in the pristine framework was shown to strongly impact the electrochemical activity, that is, the reversible capacity scales with the content of anionic vacancies. Similar to FeOF-type electrodes, upon de-lithiation, a disordered rutile phase forms, showing that the anionic chemistry dictates the atomic arrangement of the re-oxidized phase. Finally, it was shown that the nanoscaling and structural rearrangement induced by the conversion reaction allow the in situ formation of new electrode materials with enhanced electrochemical properties.     

空心阴极灯激发的微波等离子体炬原子/离子荧光光谱研究--钙的原子/离子荧光光谱

用强短脉冲供电技术的空心阴极灯作激发源、微波等离子体炬作原子／离子化器，建立了原子／离子荧光光谱实验装置。详细研究了微波等离子体功率、观察高度、空心阴极灯电流等因素对原子／离子荧光信号强度的影响，测量了系统对Ca的原子／离子荧光光谱的检出限。     

空间遥感相机长条反射镜组件的动力学特性分析

空间遥感相机长条反射镜较圆反射镜的整体刚度相差很大,整个组件在随火箭发射过程中因力学环境引起的自身位置改变导致面形的微小畸变从而对成像质量造成严重影响。因此,反射镜组件的设计就成为整个相机系统研制的重点与难点之一。对其进行科学、严谨的力学环境仿真是设计中的有效辅助手段。对某相机的长条反射镜组件动力学响应进行了较为深入的研究,借助MSC-patran,用有限元法进行了求解。获得了组件的动力学特性。     

非晶金刚石膜的性能及其应用

非品金刚石薄膜具有超高硬度等一系列优异的特殊性能，为工程界孜孜追求的材料表面镀膜。用百纳科技公司研发制造的过滤阴极真空电弧离子镀膜机镀制的非晶金刚石薄膜，SP^3金刚石结构量≥80％，硬度高，膜／基结合力高，摩擦系数小，耐磨损，耐腐蚀，透光率高，在电子，机械，光学，生物医学上有广泛应用前景。我们已在视窗玻璃，丝锥，模具，硬质合金刀头等产品上成功应用。     

采用空心阴极放电等离子体化学气相沉积方法制备a-CH薄膜

 研究了不同衬底-阴极距离、直流电压和H₂流量对a-CH薄膜沉积速率的影响。结果表明：衬底-阴极距离必须大于0.5cm，随着该距离的增加，薄膜的沉积速率减少；直流电压达550V时沉积速率最大；随着H2含量的增加，CH₄含量相对减少，沉积速率随之降低。用AFM观察了以该方法制得的448.4nm CH薄膜的表面形貌，表面粗糙度约为10nm。最后测出了不同条件下CH薄膜的UV-VIS谱，由此可以计算得到薄膜的禁带宽度及折射率。     

阴极还原处理对多孔硅发光性能的影响

对经过阴极还原处理后的多孔硅样片进行了光致发光测试和稳定性测试.实验结果表明这种处理能明显改善多孔硅的发光稳定性,使其表面结构更加稳定.利用原子力显微镜对不同还原时间的多孔硅微结构及形貌进行了比较,在一定范围内随着还原时间的增长多孔硅表面粗糙度增大,PL谱增强.     

Natural vibrations of a strip made of a composite material with a locally curved structure

The possibility of using the finite-element method for investigating two-dimensional problems on natural vibrations in the mechanics of composite materials with curved structures is considered. With the example of a hinge-supported strip made of a composite material with a locally curved structure, the influence of geometrical and mechanical parameters of the strip on its eigenfrequencies is examined. It is established that the presence of local curving in the structure of strip material decreases the magnitude of eigenfrequencies.Translated from Mekhanika Kompozitnykh Materialov, Vol. 41, No. 1, pp. 71–78, January–February, 2005.     

Simulation of Vacuum Microelectronic Triode Made of Single Carbon Nanotube

Vacuum microelectronic triode performance, based upon a unit cell with a nanotube field emitter, gate, and anode, was evaluated via computer simulation. Electron emission was calculated from the modified Fowler-Nordheim equation. The dependence of emitted current, upon geometrical factors, e.g., nanotube radius, nanotube height, and gate's hole radius, is shown. The device design parameters of trans-conductance, and cutoff frequency have been calculated, which show that this structure can be used as a microwave and millimeter wave amplifier. Electron current flux is shown for time-dependent 1–Thz sinusoidal variation frequency input.