A novel tridentate nitrogen donor as ligand in copper catalyzed ATRP of methyl methacrylate

A tridentate ligand, BPIEP: 2,6‐bis[1‐(2,6‐diisopropyl phenylimino) ethyl] pyridine, having central pyridine unit and two peripheral imine coordination sites was effectively employed in controlled/“living” radical polymerization of MMA at 90°C in toluene as solvent, Cu^IBr as catalyst, and ethyl‐2‐bromoisobutyrate (EBiB) as initiator resulting in well‐defined polymers with polydispersities M_w/M_n ≤ 1.23. The rate of polymerization follows first‐order kinetics, k_app = 3.4 × 10^?5 s^?1, indicating the presence of low radical concentration ([P*] ≤ 10^?8) throughout the reaction. The polymerization rate attains a maximum at a ligand‐to‐metal ratio of 2:1 in toluene at 90°C. The solvent concentration (v/v, with respect to monomer) has a significant effect on the polymerization kinetics. The polymerization is faster in polar solvents like, diphenylether, and anisole, as compared to toluene. Increasing the monomer concentration in toluene resulted in a better control of polymerization. The molecular weights (M_n,SEC) increased linearly with conversion and were found to be higher than predicted molecular (M_n,Cal). However, the polydispersity remained narrow, i.e., ≤1.23. The initiator efficiency at lower monomer concentration approaches a value of 0.7 in 110 min as compared to 0.5 in 330 min at higher monomer concentration. The aging of the copper salt complexed with BPIEP had a beneficial effect and resulted in polymers with narrow polydispersitities and higher conversion. PMMA obtained at room temperature in toluene (33%, v/v) gave PDI of 1.22 (M_n = 8500) in 48 h whereas, at 50°C the PDI is 1.18 (M_n = 10,300), which is achieved in 23 h. The plot of lnk_app versus 1/T gave an apparent activation energy of polymerization as (ΔE^≠_app) 58.29 KJ/mol and enthalpy of equilibrium (ΔH⁰_eq) to 28.8 KJ/mol. Reverse ATRP of MMA was successfully performed using AIBN in bulk as well as solution. The controlled nature of the polymerization reaction was established through kinetic studies and chain extension experiments. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4996–5008, 2005     

乌桕类可可脂结晶过程中表现体积变化

为了解乌桕类可可脂(CTCBE)缓冷结晶横向胀罐爆裂原因，研究CTCBE结晶过程中的膨胀特性，采用流体静力法测试了不同等温结晶条件下CTCBE结晶形成的表观密度和表观体积及其横纵向膨胀状况。结果表明，CTCBE缓冷结晶后形成外部和中部两个晶区。在5-25℃的各等温结晶范围内，当结晶温度增加时，外部结晶区域减小、表观密度变化不大；中部结晶区域增大、表观密度明显减小，CTCBE的表观体积、横向、纵向膨胀率均增大，膨胀横向大于纵向。进一步表明CTCBE在自然缓冷固化的表观体积根本上由其结晶温度决定。为有效防止横向胀罐，自然缓冷固化温度应低于10℃。     

数码相机CMOS图像传感器的特性参数与选择

介绍了数码相机的核心器件———CMOS图像传感器的特性参数和在数码相机设计过程中CMOS图像传感器的选择。选择CMOS图像传感器,不仅需要考虑包括传感器的尺寸、像素总数和有效像素数、最小照度、动态范围、灵敏度、分辨力、光电响应不均匀性以及光谱响应等在内的特性参数,而且还要考虑电源管理和功耗、模数转换位数、开发的简便性以及成本等因素。     

像管亮度增益与背景测试仪

论述像管亮度增益与背景测试仪的原理，介绍仪器的组成以及测试数据的处理方法。     

起爆药爆轰场和燃烧场的干涉法显示及其图像处理

本文介绍了利用脉冲YAG激光引爆起爆药产生爆轰流场或燃烧温度场,用时间序列干涉法首次获得了爆轰流场和起始燃烧过程的时间序列干涉图的实验结果.在此基础上,采用条纹曲线检测法和双三次多结点插值样条函数从干涉图上提取爆轰场冲击波的波阵面,并通过序列波阵面配准算法,定量地计算了冲击波的传播速度.同时,还定量计算了燃烧场温度随时间变化的分布.     

狭缝式高速摄影机胶片的计算机判读

根据狭缝摄影机胶片的成象原理,运用数字图象处理技术,对狭缝式高速摄影机胶片判读工作的计算机化进行研究.应用结果表明,该技术先进实用,极大地提高了判读的精度和效率,将是这种胶片判读技术的发展方向.     

数码相机引入科技照像实验

介绍了数码相机的系统结构和工作原理，通过与传统相机的对比分析，在科技照相实验中应该使用数码相机。     

高固体分羟基丙烯酸树脂的合成

以过氧化二苯甲酰（BPO）／过氧化二异丙苯（DCP）（质量比为2：3）为复合引发剂，二甲苯为溶剂，选用适量含羟基单体和分子量调节剂，以减缓树脂合成聚合反应中的自动加速现象，合成了分子量为3000-4000，多分散性指数d〈2的高固体分羟基丙烯酸树脂．该树脂与缩二脲多异氰酸酯（HDI）的配漆实验证明，所得漆膜鲜映性好、丰满度高、色泽好、雾影值低、综合性能较好．     

Mathematical topographical correction of XPS images using multivariate statistical methods

For rough heterogeneous samples, the contrast observed in XPS images may result from both changes in elemental or chemical composition and sample topography. Background image acquisition and subtraction are frequently utilized to minimize topographical effects so that images represent concentration variations in the sample. This procedure may significantly increase the data acquisition time. Multivariate statistical methods can assist in resolving topographical and chemical information from multispectral XPS images. Principal component analysis (PCA) is one method for identification of the highest correlation/variation between the images. Topography, which is common to all of the images, will be resolved in the first most significant component. The score of this component contains spatial information about the topography of the surface, whereas the loading is a quantitative representation of the topography contribution to each elemental/chemical image. The simple‐to‐use self‐modelling mixture analysis (Simplisma) method is a pure variable method that searches for the source of most differences in the data and therefore has the potential to distinguish between chemical and topographical phases in images. The mathematical background correction scheme is developed and validated by comparing results to the experimental background correction for samples with differing degrees of topography. Copyright © 2004 John Wiley & Sons, Ltd.     

数码相机原理与系统设计研究

介绍了数码相机的工作原理 ,分析了数码相机的系统结构 ,提出了设计数码相机的处理流程。典型的数码相机系统有镜头、闪光灯、光学取景器、LCD显示屏、图像数据存储扩展设备接口、图像数据传输接口、供电系统以及核心处理器等八个主要模块。数码相机的数据流向从图像传感器开始 ,止于图像数据的存储和传输。数据流的处理主要包括模数转换、光学黑电平钳位、针对镜头的边缘畸变的运算修正、坏像素处理、白平衡处理、伽马校正、色彩合成处理、边缘检测 (锐度检测 )和伪彩色检测 (伪彩色抑制 )、JPEG压缩和图像存储器等模块