一种漂移室定位子性能反常现象的研究

研究了一种漂移室定位子性能的反常现象,它关系到定位子的使用寿命．着重测量了暗电流和随机噪声与时间、高压及温度的关系.     

水平管外强化凝结传热的数值解

以Nusselt理论为基础,运用三维坐标建立了肋片侧面的冷凝传热模型,对肋片侧面的冷凝传热机理进行了分析,得出了肋片侧面表面传热系数的积分表达式。利用此法对水平环肋单管表面传热系数进行计算并将结果与传统解法进行比较。     

水闸闸室结构三维样条边界元分析

用三维样边界元法分析水闸闸室结构。底板，闸墩和载水墙等为其子结构，交通桥，工作桥和胸墙等处理为内部支撑。地基和边载可以是任意的，只要能给定地表位移面力关系。在各种工况下，不论是设置平板门还是弧形门，是平底板是反拱底板，即使在稀疏剖分下也能给出高精度的位移场，应力场和地基反力场。     

Determination of impurities in highly pure platinum by inductively coupled plasma-atomic emission spectrometry

In this work, a cyclone spray chamber system is used in conjunction with an inductively coupled plasma-atomic emission spectrometer instead of the conventional Scott-type chamber system to reduce the lower limit of detection achieved by the instrument, and an internal standard element (Y) is introduced to eliminate the effects caused by the drift in the plasma background level. An ICP-AES method for the determination of 13 impurity elements in a highly pure platinum sample has been developed. In this method, it is not necessary either to add a platinum matrix to the calibration standard or to separate and concentrate the elements to be determined in the samples. The effect of the platinum matrix on the elements to be analyzed is corrected for by a background equivalent concentration subtraction method. The determination ranges of the method are as follows: 0.00010-0.0050% for Mg, Mn, Cu, Ag, Fe and Zn; 0.00030-0.015% for Au, Ir, Ni and Pb; 0.00050-0.025% for Rh and Al; and 0.00080-0.040% for Pd. The method is simple, rapid and accurate, and can be applied to the analysis of 99.9–99.995% pure platinum.     

Deposition of Oral Bacteria and Polystyrene Particles to Quartz and Dental Enamel in a Parallel Plate and Stagnation Point Flow Chamber

The aim of this paper is to determine to what extent (i) deposition of oral bacteria and polystyrene particles, (ii) onto quartz and dental enamel with and without a salivary conditioning film, (iii) in a parallel plate (PP) and stagnation point (SP) flow chamber and at common Peclet numbers are comparable. All three bacterial strains showed different adhesion behaviors, and even Streptococcus mitis BMS, possessing a similar cell surface hydrophobicity as polystyrene particles, did not mimic polystyrene particles in its adhesion behavior, possibly as a result of the more negative ζ potentials of the polystyrene particles. The stationary endpoint adhesion of all strains, including polystyrene particles, was lower in the presence of a salivary conditioning film, while also desorption probabilities under flow were higher in the presence of a conditioning film than in its absence. Deposition onto quartz and enamel surfaces was different, but without a consistent trend valid for all strains and polystyrene particles. It is concluded that differences in experimental results exist, and the process of bacterial deposition to enamel surfaces cannot be modeled by using polystyrene particles and quartz collector surfaces.     

Measurement of attachment force of microbial cells

A parallel-plate flow chamber consisting of two transparent electro-conductive glass plates was constructed. The two glass plates were set parallel to each other and connected to a potentiostat apparatus to regulate the strength of the electric field between the plates. A microbial cell suspension was flowed through the chamber. This system enabled the application of an electrostatic force to suspend charged particles, e.g. microbial cells, existing between the two plates. The time course of the cell attachment of Pseudomonas syringae pv. atropurpurea NIAES 1309 suspended in 10 mM phosphate buffer solution (pH 7.0) to the glass plate was investigated at various electric field strengths ranging from −4.2 to +4.1 V cm⁻¹. The attachment rate and the maximum number of attached cells increased linearly with the increase in the strength of the positive electric field. In contrast, the rate and the number of cells decreased linearly with the decrease in the strength of the negative electric field. These linear relations gave a specific value for the strength of the electric field (−5.9 ± 0.7 V cm⁻¹) where the electrostatic repulsion and the microbial attachment force were thought to be equal, resulting in no cell attachment. From this value, the electrostatic repulsion, i.e. the microbial attachment force, was calculated to be 5.0 × 10⁻¹¹ N cell⁻¹ for cells of average size.     

Physicochemical aspects of microbial adhesion — Influence of antibody adsorption on the deposition ofStreptococcus sobrinus in a parallel-plate flow chamber

Deposition of the oral bacteriumStreptococcus sobrinus HG977 onto glass (water contact angle 0°) and onto FEP-Teflon (fluoroethylenepropylene; water contact angle 110°) was studied in a parallel-plate flow chamber in the presence and absence of polyclonal antibodies (pAb) and monoclonal antibodies (mAbs) adsorbed onto the cells. The zeta potentials of the bacteria ranged from −7.1 to −8.5 mV at pH 6.8 and were not affected by the presence of pAb or mAbs. Hydrophobicity (by water contact angles) increased from 30° (no antibodies) to 88° in the presence of pAb adsorbed onto the bacterial cell surface. The untreatedS. sobrinus had a greater tendency to adhere to glass (44.5 × 10⁶ cm⁻²) than to FEP-Teflon (18.3 × 10⁶ cm⁻²), in accordance with thermodynamic modelling. After preincubation ofS. sobrinus with pAb, its clear preference for adhesion to glass disappeared as expected from its increased hydrophobicity. Although forS. sobrinus preincubated with OMVU10 no difference was found in hydrophobicity in comparison to the untreated bacteria, the number of bacteria adhering to glass decreased to 10.2 ¢ 10⁶ cm⁻². Formation of bacterial aggregates was found whenS. sobrinus, preincubated with pAb or OMVU10, adhered to glass and FEP. This was also observed when untreated bacteria adhered to glass coated with OMVU10, or to FEP coaled with OMVU10 or pAb. Adhesion in these experiments is therefore thought to occur via near-neighbour collection induced by the presence of pAb or mAbs. Low numbers of bacteria were removed from glass after draining the flow cell, whereas high numbers of untreated bacteria and bacteria preincubated with OMVU10 were removed from FEP.S. sobrinus cells preincubated with pAb were not removed but piled up. It was concluded that the adhesion of untreatedS. sobrinus andS. sobrinus preincubated with pAb is in accordance with thermodynamic modelling, based on the overall wettability of the cell surfaces, whereas the adhesion ofS. sobrinus preincubated with OMVU10 may be through localized interactions, not expressed in overall surface properties.     

Studying dispersoid systems

Summary Measurements of energy transformation in mitochondria are done on a capillary differential titration calorimeter CTD2156. It is important to mention that a sediment is quickly formed by the mitochondria suspension without mixing by means of a vibrating needle. During the measurements, the vibrating needle is located inside the working volume of the chamber. The design of the calorimeter is substantiated theoretically. It provides a new mode of a reagent input in the measuring volume of the calorimetric chambers. It expands the spectrum of tasks that can be solved using this instrument. In the capillary calorimeter the calorimetric chambers unit is simple and small in size. These advantages of capillary chambers provide an opportunity to unite 20 capillary calorimetric chambers in one calorimetric block. It allows designing a multi-channel titration calorimeter. There are obvious advantages of such a calorimeter over other instruments in screening researches and in researches of objects maintaining stability only for a short time.     

用环形扩散管和滤纸联用采样技术采集空气中氨和铵盐

建立了环形扩散管和滤纸采样夹联用，分形态同时采集空气中所态氨和颗粒态铵盐的方法。在同一气流中，采用涂渍１．５％草酸乙醇水溶液的环形扩散管采集气态氨，用浸渍上述试剂的玻璃纤维纸和慢速定量滤纸分别采集颗粒安和第一层滤纸上的铵盐挥发产生的氨气。用靛酚蓝比色法分别测定氨和铵盐。当采气流速为１．０Ｌ／ｍｉｎ时，采样效率高于９８．２％。将本法测得的氨气和铵盐的总量与标准采样方法的测定结果比较。无显著性差异（Ｐ     

A new approach for the sequential injection spectrophotometric determination of the total antioxidant activity

A sequential injection system based on the ABTS (2,2′-azino-bis-(3-ethylbenzothiazoline-6-sulphonic-acid) methodology was developed. The proposed method, incorporating a mixing chamber in the side port of the selection valve, was evaluated to measure the total antioxidant activity of several beverages and foods.The ABTS⁺ is generated by oxidation of ABTS with potassium persulfate and is reduced in presence of hydrogen-donating antioxidants converting into a colourless product. The applicability of the developed method was tested by measurement of the antioxidant activity of pure compounds as well as by analysing complex food and beverage samples. The antioxidant activity was presented as l(+) ascorbic acid equivalence. The values obtained by this methodology were not significantly different from the results obtained by the original spectrophotometric ABTS assay. For most of the studied antioxidants, antioxidant activity varied with pH and dilution. The proposed SIA system is suitable for screening direct or diluted total antioxidant activity of pure compounds or food samples.