Wave-based vibration control of large cable net structures

Large cable net structures have been widely applied in aerospace engineering due to the feature of light-weight, high packaging efficiency, and high thermal stability. Structural vibrations induced by a variety of disturbances are inevitable in the space environment, resulting in the requirement of effective vibration control strategies for large cable net structures. Since the large cable net structures have many closely spaced vibrational modes in the range of low frequencies, traditional modal based control may cause modal truncation and spillover problems. In this paper, a wave-based boundary control strategy is adopted and its effectiveness to control the vibration of cable net structures is investigated, by transfer function analysis and numerical methods. It is found that the structural vibration can be absolutely resisted by applying the wave-based boundary controllers onto all the exterior nodes, when disturbances come from the external boundaries of the cable net. Our results in this paper can provide a theoretical basis for the vibration control of large cable net structures.     

Dominant modes of submerged thin cylindrical shells

The relationship between the dominant mode of the submerged thin cylindrical shell and the flexural wave velocity is investigated. The natural frequency corresponding to the vibration mode is obtained as the solution of characteristic equation of thin cylindrical shell. However, it is difficult to estimate the dominant mode, especially if two or more vibration modes are involved. To estimate the dominant mode of a thin shell in vacuo, the concept of “modified bending stiffness” has been introduced. In this paper, the concept of modified bending stiffness is extended to estimate the dominant mode of a submerged thin cylindrical shell. The dominant mode of a submerged thin cylindrical shell is theoretically discriminated from the other mode based on the smallness of the modified bending stiffness of the submerged shell. The validity of our theory is confirmed by a good agreement between theoretical and experimental results on flexural wave velocity.     

利用振幅调制器进行光电负反馈抑制激光强度噪声

采用振幅调制器作为抑制激光强度噪声的元件，首先对光电负反馈回路进行了简要的理论分析，然后利用该光电负反馈进行抑制激光二极管抽运全固化单频环形Nd:YVO4红外激光器强度噪声的实验。结果表明，在0－1MHz的低频段，强度噪声大幅度降低，最大降低约15dB。     

用能量法求多自由度振动系统的角频率

利用简谐振动能量方程，通过分析振幅矢量的关系，用能量法求多自由度振动系统的角频率或简正振动频率。     

水平均匀大气中多束光在接收面上的相关性及其对光强起伏的影响

在科尔莫戈罗夫理论的基础上，推广了光束在接收面上相关函数的物理含义。分析了多光束在接收面上的相关性。并在此基础上形成多光束光强起伏方差的解析表达式。分析结果表明，随着信道间距的增加，信道相关性下降。到达接收面的光强起伏方差降低；当信道完全重合，即相关系数变为1时，叠加后的光强起伏方差没有明显降低。与单光束时没有区别；在允许范围内增加光束数目可降低光强起伏。     

Measurements of Time-Varying Characteristics of Optical Signals and Inhomogeneities of Tested Substances with Additional Phase Modulation

The problem of investigation of the amplitude and phase structure of a time-varying probing optical signal and the structure of time-varying inhomogeneities of a substance tested by this signal is considered. The analysis is concerned, in particular, with determination of the structure of signals and processes with resolution in the pico- and femtosecond range. The scheme used for the analysis is based on registration of four spatially separated spectra of the studied radiation. The spectra are formed in a four-channel scheme with a twin-wave Michelson interferometer and a spectral device. Modulators based on electrooptical crystals (perovskites) are placed in the channels. The sum spectra are formed: without modulators, with the effect of either of the modulators, and with both of them affecting the radiation. The effect of the studied substance implies either modulating the radiation (in this case it is described by multiplication) or redistributing the radiation (then it is described by convolution).     

Measurements of Optical Signals and Their Spectra in the Femtosecond Range with Additional Phase Modulation

A solution to the phase problem in optics is considered within the context of the analysis of signals changing in time and of the effect of an object under investigation on the probing radiation. The solution is based on the use of a twin-wave interferometer with phase modulation in one of the channels and a spectrometer. The analysis is concerned, in particular, with signals and processes of ultrashort duration. To shift the frequency in the interferometer channel, an electrooptical crystal of ferroelectric perovskite is used as the modulator. Errors of amplitude and phase structures determined are analyzed.     

Analysis of end point vibrations of a two-link manipulator by integrated CAD/CAE procedures

In this work, the effect of flexibility on the trajectory of a planar two-link manipulator is studied using integrated computer-aided design/analysis (CAD/CAE) procedures. The solid models and finite element models of the parts of the manipulator are created by using the CAD/CAE software I-DEAS. The assembly is defined, and knowing the payload and the end point trajectory, the velocities and accelerations of the parts, joint forces and driving torques are calculated using the rigid body dynamics. All the time dependent nodal forces acting on the parts including distributed gravity and inertia forces are created in files with the I-DEAS program file format. The finite element vibration analysis of the parts is performed by I-DEAS. The end point vibrations and the deviations from the rigid-body trajectory are analyzed for different types of end point acceleration curves. A circular trajectory is considered as an example. It is observed that the precision of the manipulator can be increased by testing different end point acceleration curves without changing the trajectory and the duration of the end point work. The procedure explained in this work can be used for this purpose successfully.     

提高微波功率源性能的一种新型控制系统

本控制系统用于抑制大功率速调管输出微波功率宏脉冲平顶波纹,改善电子直线加速器输出束流的品质.控制方法采用微分线性逼近和矩阵算法对系统的输入和输出进行分析,求出代表系统响应的传输矩阵,从而将复杂的激励一响应计算转化为简单的代数运算.实验结果显示出宏脉冲平项波纹得到了有效抑制,说明采用自适应前馈控制来获得平坦的宏脉冲平顶是切实可行的.     

Analysis method of the effect of fabrication errors on a planar waveguide demultiplexer

The impact of fabrication errors on a planar waveguide demultiplexer is analyzed based on an analytical method. The explicit expression of the transfer function taking into account phase and amplitude errors is presented in order to analyze the loss and crosstalk of the demultiplexer caused by fabrication errors. A basic requirement for the demultiplexer with a certain crosstalk criterion can be easily obtained. Using an etched diffraction grating demultiplexer as an example, it is shown that the analytical results have a good agreement with results from a numerical method.