Strain effects on multiferroic BiFeO3 films

The field of multiferroics has experienced a rapid progress resulting in the discovery of many new physical phenomena. BiFeO₃ (BFO) compound, which is one of the few room-temperature single-phase multiferroics, has contributed subsequently to this progress. As a result, significant review articles have been devoted specifically to this famous system. This chapter is dedicated to the strain effects on the structure stability and property changes of BFO thin films. It is a short and non-exhaustive topical overview that may be seen as an invitation for interested readers to go beyond. There is a very active and prolific research in this field and we apologize to the authors whose relevant work is not cited here. After a short introduction, we will thus review the effect of strain on BFO films by describing the consequences on the structure and the phase transitions as well as on polar, magnetic and magnetoelectric properties.     

A study of structural, compositional and optical properties of spray-deposited non-stoichiometric (Zn,Fe)S thin films

Non-stoichiometric ternary chalcogenides (Zn,Fe)S were prepared in the film form by pyrolytic spray deposition technique, using air/nitrogen as the carrier gas. The precursor solution comprised of ZnCl₂, FeCl₂ and thiourea. The depositions were carried out under optimum conditions of experimental parameters viz. carrier gas (air/nitrogen) flow rate, concentration of precursor constituents, nozzle substrate distance and temperature of quartz substrate. The deposited thin films were later sintered in argon at 1073 K for 120 min.The structural, compositional and optical properties of the sintered thin films were studied. X-ray diffraction studies of the thin films indicated the presence of (Zn,Fe)S solid solution with prominent cubic sphalerite phase while surface morphology as determined by scanning electron microscopy (SEM) revealed a granular structure.The chemical composition of the resulting thin films as analyzed by energy dispersive X-ray analysis (EDAX) reflected the composition of the precursor solutions from which the depositions were carried out with Fe at% values ranging from 0.4 up to 33.SEM micrographs of thin films reveal that the grain sizes of the thin films prepared using air as carrier gas and N₂ as carrier gas are in the vicinity of 300 and 150 nm, respectively.The diffuse transmittance measurements for thin films, as a function of wavelength reveal the dependence of direct optical band gap on Fe content and type of phase.     

Electrical properties and Schottky diodes using N-N′diphenyl-1-4phenylenediamine

Thin films of, N-N′diphenyl 1-4phenylene-diamineane are prepared using vacuum sublimation technique. The electrical conductivity from room temperature down to 127 K is studied. It is found that the conduction of charge carriers obeys T^−1/2 dependence on temperature. The average hopping distance, hopping energy, density of states and their variation due to post-deposition heat treatment are studied. Schottky diodes are fabricated with gold as ohmic contact and aluminium as Schottky contact. From the observed current voltage characteristics the saturation current density, diode ideality factor and the barrier height are determined. Their variation with air annealing is also investigated.     

Noise-assisted mound coarsening in epitaxial growth

Two types of mechanisms are proposed for mound coarsening during unstable epitaxial growth: stochastic, due to deposition noise, and deterministic, due to mass currents driven by surface energy differences. Both yield the relation H=(RWL)² between the typical mound height W, mound size L, and the film thickness H. An analysis of simulations and experimental data shows that the parameter R saturates to a value which discriminates sharply between stochastic () and deterministic () coarsening. We derive a scaling relation between the coarsening exponent 1/z and the mound-height exponent which, for a saturated mound slope, yields . Received: 11 November 1997 / Revised in final form: 28 November 1997 / Accepted: 28 November 1997     

Property improvement of pulsed laser deposited boron carbide films by pulse shortening

Growth characteristics and surface morphology of boron carbide films fabricated by ablating a B₄C target in high vacuum with a traditional KrF excimer laser and a high brightness hybrid dye/excimer laser system emitting at the same wavelength while delivering 700 fs pulses are compared. The ultrashort pulse processing is highly effective. Energy densities between 0.25 and 2 J cm⁻² result in apparent growth rates ranging from 0.017 to 0.085 nm/pulse. Ablation with nanosecond pulses of one order of magnitude higher energy densities yields smaller growth rates, the figures increase from 0.002 to 0.016 nm/pulse within the 2-14.3 J cm⁻² fluence window. 2D thickness maps derived from variable angle spectroscopic ellipsometry reveal that, when ablating with sub-ps pulses, the spot size rather than the energy density determines both the deposition rate and the angular distribution of film material. Pulse shortening leads to significant improvement in surface morphology, as well. While droplets with number densities ranging from 1 × 10⁴ to 7 × 10⁴ mm⁻² deteriorate the surface of the films deposited by the KrF excimer laser, sub-ps pulses produce practically droplet-free films. The absence of droplets has also a beneficial effect on the stoichiometry and homogeneity of the films fabricated by ultrashort pulses.     

红光激发下掺Ho3+氟化物薄膜的上转换发光

利用激光脉冲沉淀法制备了稀土Ho~(3 )掺杂的氟化物薄膜。观测到处于薄膜中的Ho~(3 )离子在632.8nm红光激发下的上转换发射。这些上转换发射包括:~5S_2→~5I_7,~5F_4→~5I_7和~5S_2→~5I_8。     

热丝加热电流对CH薄膜沉积速率和表面形貌的影响

 热丝辅助裂解法是结合气相沉积制备聚对二甲苯薄膜和热丝化学气相沉积而形成的一种制-CH薄膜的新方法。热丝辅助裂解法的最大特点就是在保持低衬底温度情况下可以获得高沉积速率，而热丝加热电流对薄膜沉积速率和薄膜表面形貌具有重要影响。研究表明，热丝加热电流越大，薄膜沉积速率越高，在加热电流9A时，薄膜沉积速率可达0.002mm/min，同时薄膜表面粗糙度随之增加，薄膜表面也开始出现其它元素污染，因此，一般热丝加热电流选择为7A附近。     

Polarization modification of PZT thin films by means of electric fields and stress in scanning force microscopy

Polarization switching in scanning force microscopy (SFM) is influenced by both electric fields and stress, whereby the latter can arise inherently from Maxwell stress. We discuss the influence of electric charges and of the polarization asymmetry on the switching behaviour. For single crystallites of PZT(53/47) thin films, the sectors for ferroelectric, ferroelastoelectric and ferroelastic switching are represented in a field-stress map. The influence of stress on the second harmonic of the SFM is also discussed.