Rocky coast processes: with special reference to the recession of soft rock cliffs

Substantial progress in research on the recession of coastal cliffs composed of soft materials has been made in recent years and data with higher accuracy have been accumulated. This paper provides the state of the art review in the recession studies and highlights two new findings obtained from the reanalysis of existing data. The review topics are: episodic and localized nature of cliff recession; the development of cliffline; the relationship between cliff height and recession rate; mechanisms of cliff toe erosion by waves; a fundamental equation for wave-induced toe erosion; factors controlling toe erosion; and slope instabilities and mass movements. The findings are presented on (1) the temporal change in cliffline recession mode and (2) the effect of beach sediment at the cliff base on the cliff erosion.     

V20+离子1s23d-1s2nf的跃迁能和振子强

用全实加关联方法计算了类锂V20+离子1s23d-1s2nf的跃迁能和偶极振子强度.依据量子亏损理论, 确定了1s2nf系列的量子数亏损,用这些作为能量的缓变函数的量子亏损,实现对该Rydberg系列任意高激发态(n≥10)的能量的可靠预言.将这些分立态振子强度与量子亏损理论相结合,得到在电离域附近束缚态间的偶极跃迁振子强度以及束缚态-连续态跃迁的振子强度密度,从而将V20+离子的这一重要光谱特性的理论预言外推到整个能域.     

Tensile behaviour of corroded and hydrogen embrittled 2024 T351 aluminum alloy specimen

The synergetic effect of corrosion and corrosion induced hydrogen embrittlement damage processes which occur at local scale has been found to result in a dramatic macroscopic tensile ductility loss of the 2024 aluminum alloy. In the present work, the tensile behaviour of corroded 2024 T351 specimens has been estimated on the basis of FE analysis by taking into account the local material properties in the damaged areas. A parametric study is involved to account for the effect of thickness in the results. Calculated tensile properties obtained with the analysis agree well with experimental data.     

Stress-Strain State in the Zone of Load Transfer in a Composite Specimen under Uniaxial Tension

The stress-strain state in the zone of load transfer in a uniaxially stretched specimen made of a unidirectional epoxy carbon-fiber-reinforced plastic (CFRP) is investigated. A parametric analysis of the influence of geometric and mechanical characteristics of the specimen on its stress-strain state is performed by means of finite-element modeling. The parameters allowing us to significantly reduce the dangerous concentration of transverse and tangential stresses are revealed. The mechanical tensile characteristics of a high-strength pultruded unidirectional CFRP are determined experimentally, and the size effect of its strength is estimated.     

On the hysteresis of vortex shedding in a periodically-varying flow

Efforts are made to explore the hysteresis characteristics of vortex shedding in a pipe flow, whose velocity varies periodically in time. Results obtained show that during acceleration of the flow, the vortex strength tends to be stronger, whereas during deceleration of the flow, the situation is reversed. As reconstructed from the velocity signals measured at a point in the flow field, the shed vortex arrays appear to possess uneven vortex strengths in response to periodically-varying incoming flows. Furthermore, in the hysteresis range, the streamwise spacings between the vortices appear to be unequal.     

Influence of SiO2 in SiCp on the microstructure and impact strength of Al/SiCp composites fabricated by pressureless infiltration

The effect of SiO₂ in SiC_p and the following processing parameters on the microstructure and impact strength of Al/SiC_p composites fabricated by pressureless infiltration was investigated: Mg content in the aluminum alloy, SiC particle size, and holding time. Preforms of SiC_p in the form of rectangular bars (10 × 1 × 1 cm) were infiltrated at 1150°C in an argon→nitrogen atmosphere for 45 and 60 min by utilizing two aluminum alloys (Al-6 Mg-11 Si and Al-9 Mg-11 Si, wt.%). The results obtained show that the presence of SiO₂ in SiC affects the microstructure and impact strength of the composites significantly. When Al₄C₃ is formed, the impact strength decreases. However, a high proportion of SiC to SiO₂ limits the formation of the unwanted Al₄C₃ phase in the composites. Also, a higher content of Mg in the Al alloy lowers the residual porosity and, consequently, increases the composite strength. The impact strength grows with decrease in SiC particle size and increases considerably when the residual porosity is less than 1%. Russian translation published in Mekhanika Kompozitnykh Materialov, Vol. 42, No. 3, pp. 401–418, May–June, 2006.     

Interpretation of the polyelectrolyte and antipolyelectrolyte effects of poly(N‐vinylimidazole‐co‐sodium styrenesulfonate) hydrogels

Hydrogels of N‐vinylimidazole (VI) and sodium styrenesulfonate (SSS) were synthesized in aqueous solution by radical crosslinking copolymerization with N,N′‐methylene‐bis(acrylamide) as crosslinker. Swelling in several saline solutions was measured for hydrogel samples synthesized with different comonomer concentrations (C_T = 10, 25, or 40%) and with SSS mole fractions covering a broad range (f_SSS = 0–0.7), while the crosslinker ratio was 2 wt % in all cases. The degree of swelling in aqueous solution with a specific ionic strength (μ), plotted versus the SSS composition of the feed, shows a minimum for any set of samples synthesized with a fixed C_T. The dependence of swelling on μ shows both polyelectrolyte (f_SSS beyond the minimum) and antipolyelectrolyte behaviors (in the low f_SSS limit). It was found that the nonGaussian factor of the crosslinking density and the polymer‐solvent interaction parameter increase with f_SSS for any C_T. Moreover, in the low f_SSS limit, the osmotic swelling pressure is governed not only by the ionic contribution, but also by the polymer‐solvent mixing and, the concentration of mobile counterions inside the gel is not proportional to the net fixed charge but to the addition of cationic and anionic side groups, what discards the formation of ionic pairs. The antipolyelectrolyte effect is interpreted as due to the increasing protonation of VI as μ goes up. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1683–1693, 2007     

具有高机械强度的掺Er~(3 )∶TeO_2-Nb_2O_5玻璃的光谱性质研究

熔制了掺铒碲铌玻璃样品(100-X)TeO2-XNb2O5(X=5,10,15,20mol%),测试了其密度、折射率、转变温度、析晶温度、维氏机械强度、吸收光谱、荧光光谱、荧光寿命等参量。利用Judd-Ofelt和McCumber理论分别计算了铒离子强度参量Ωt(t=2,4,6)和受激发射截面σemi的大小,研究了掺铒碲铌玻璃样品光谱参量对Nb2O5成分的依赖性,并与典型的碲锌钠玻璃(75TeO2-20ZnO-5Na2O)在热学、机械强度、光谱性质和放大品行四个方面进行了比较.     

Strength of cylinder joint adhesively bonded by coupling

Summary A method of joining two metal cylindrical shafts with adhesive coupling is proposed. Two cylindrical shafts with the same diameter are connected by bonding through a cylindrical coupling with epoxy resin. The strength of the shaft joint under tensile loading and torsional loading is investigated analytically and experimentally. The stress and strain distributions of the shaft joint is analyzed by the finite element method. The analyzed strain distributions in the joint are compared with experimental values. The joint strength is predicted by applying the strength laws of shafts, coupling, adhesive layer and adhesive interface between shaft and adhesive coupling. The effects of the coupling dimension on the joint strength are examined. It is shown that the adhesive shaft joint can transfer the load by which the cylindrical shafts are plastically deformed.This paper was refined by the author, K. Ikegami, during statying at Technische Universität München under the support of Deutscher Akademischer Austauschdients. The author is grateful to Professor Lippmann of Technische Universität München who is the host professor of the support.     

Towards understanding the increase in strength of thermotropic polyesters with heat treatment

Thermotropic copolyester fibers of oxynaphthoate and oxybenzoate have been subjected to conditions that promote solid-state polymerization as well as annealing. The annealing process causes the crystals to perfect with a simultaneous increase in heat of fusion and melting temperature. Solid-state polymerization, a reaction rate-controlled process, causes the polymer viscosity average molecular weight to increase by chain extension from about 14,000 g/mole to more than 87,000 g/mole with a simultaneous impressive increase in tenacity from about 10 g/d (1.2 GPa) to almost 30 g/d (3.7 GPa). To understand the changes in mechanical properties, we have modeled the fiber structure as short rod-like molecules poorly bonded to a continuous matrix of parallel molecules. Lengthening of the reinforcing molecules facilitates better transfer of load from matrix to molecules, resulting in higher tenacity fibers. © 1994 John Wiley & Sons, Inc.