Orientation dependent size effects in thermal buckling and post-buckling of nanoplates with cubic anisotropy

In this work, a continuum model is presented for size and orientation dependent thermal buckling and post-buckling of anisotropic nanoplates considering surface and bulk residual stresses. The model with von-Karman nonlinear strains and material cubic anisotropy of single crystals contains two parameters that reflect the orientation effects. Using Ritz method, closed form solutions are given for buckling temperature and post-buckling deflections. Regarding self-instability states of nanoplates and their recovering at higher temperatures, an experiment is discussed based on low pressurized membranes to verify the predictions. For simply supported nanoplates, the size effects are lowest when they are aligned in [100] direction. When the edges get clamped, the orientation dependence is ignorable and the behavior becomes symmetric about [510] axis. The surface residual stress makes drastic increase in buckling temperature of thinner nanoplates for which a minimum thickness is pointed to stay far from material softening at higher temperatures. Deflection of [100]-oriented buckled nanoplates is higher than [110] ones but this reverses at higher temperatures. The results for long nanoplates show that the buckling mode numbers are changed by orientation which is verified by FEM.     

Defects related emission and nanosecond optical power limiting in CuS quantum dots

We report optical and nonlinear optical properties of CuS quantum dots and nanoparticles prepared through a nontoxic, green, one-pot synthesis method. The presence of surface states and defects in the quantum dots are evident from the luminescent behavior and enhanced nonlinear optical properties measured using the open aperture Z-scan, employing 5 ns laser pulses at 532 nm. The quantum dots exhibit large effective third order nonlinear optical coefficients with a relatively lower optical limiting threshold of 2.3 J cm⁻², and the optical nonlinearity arises largely from absorption saturation and excited state absorption. Results suggest that these materials are potential candidates for designing efficient optical limiters with applications in laser safety devices.     

Strategies for synthesizing non-bioaccumulable alternatives to PFOA and PFOS

This minireview describes the strategies for synthesis of fiuorinated surfactants potentially nonbioaccumulable.Various strategies have been focused on(Ⅰ) reducing the length of the perfluorocarbon chain,(Ⅱ) introducing hetero atoms into the fluorocarbon chain,(Ⅲ) introducing branch(herein and after branch means the fluoro-carbon chain section is not straight).In most cases,the surface tensions versus the surfactant concentrations have been assessed.These above strategies led to various highly fiuorinated(perfluorinated or not perfluorinated) surfactants whose chemical changes enabled to obtain novel alternatives to perfluorooctanoic acid(PFOA) and perfluorooctane sulphonate(PFOS).     

Probing the Catalytic Activity of Reduced Graphene Oxide Decorated with Au Nanoparticles Triggered by Visible Light

Hybrid materials in which reduced graphene oxide (rGO) is decorated with Au nanoparticles (rGO–Au NPs) were obtained by the in situ reduction of GO and AuCl₄^?_(aq) by ascorbic acid. On laser excitation, rGO could be oxidized as a result of the surface plasmon resonance (SPR) excitation in the Au NPs, which generates activated O₂ through the transfer of SPR‐excited hot electrons to O₂ molecules adsorbed from air. The SPR‐mediated catalytic oxidation of p‐aminothiophenol (PATP) to p,p′‐dimercaptoazobenzene (DMAB) was then employed as a model reaction to probe the effect of rGO as a support for Au NPs on their SPR‐mediated catalytic activities. The increased conversion of PATP to DMAB relative to individual Au NPs indicated that charge‐transfer processes from rGO to Au took place and contributed to improved SPR‐mediated activity. Since the transfer of electrons from Au to adsorbed O₂ molecules is the crucial step for PATP oxidation, in addition to the SPR‐excited hot electrons of Au NPs, the transfer of electrons from rGO to Au contributed to increasing the electron density of Au above the Fermi level and thus the Au‐to‐O₂ charge‐transfer process.     

Temperature effects on surface activity and application in oxidation of toluene derivatives of CTAB-SDS with KMnO4

The γ_cmc values of CTAB-SDS decrease from 63.67 mN/m at 10‡C to 36.38 mN/m at 90‡C, slightly lower than those of either CTAB or SDS. Correspondingly, the CMC of CTAB-SDS decreases almost by half. The increase of surface activity of CTAB-SDS can be attributed to the relatively weak electrostatic interaction at high temperature, which is supported by the increase of solubility of CTAB-SDS with rise in temperature. Catalytic effect on oxidation of toluene derivatives with potassium permanganate follows the order CTAB-SDS > SDS > CTAB. This is not caused by the dissociative effect of CTAB-SDS with low surface activity at low temperature, as seen from the fact that almost all oxidative products can be retrieved for different toluene derivatives and surfactants by mimicking the conditions of reaction. In the emulsifications of toluene derivatives at 90‡C, the time that turbid water layers of surfactant solutions take to become clear is the same as that of the catalytic effect on oxidation of toluene derivatives. Thus, it can be inferred that surfactants can improve the oxidation yields of toluene derivatives by increasing the contact between two reacting phases.     

Effect of absorbed pump power on the quality of output beam from monolithic microchip lasers

The dependence of the beam propagation factor (M ² parameter) with the absorbed pump power in the case of monolithic microchip laser under face-cooled configuration is extensively studied. Our investigations show that the M ₂ parameter is related to the absorbed pump power through two parameters (α and β) whose values depend on the laser material properties and laser configuration. We have shown that one parameter arises due to the oscillation of higher order modes in the microchip cavity and the other parameter accounts for the spherical aberration associated with the thermal lens induced by the pump beam. Such dependency of M ² parameter with the absorbed pump power is experimentally verified for a face-cooled monolithic microchip laser based on Nd³⁺ -doped GdVO₄ crystal and the values of α and β parameters were estimated from the experimentally measured data points.     

激光除冰研究

架空输送电线路因覆冰而导致的事故危害性很大,本文总结了目前国内外输电线路导线覆冰的现状。统计国内外探索出来的各种预防,融化,除冰等很多解决方案。通过研究和探讨,分析导线覆冰的传热和能量,运用了多种激光器进行激光熔(除)冰实验,比较研究二氧化碳激光器的除冰情况。以及提出激光熔冰的方法、研究方向和前景。     

Surface structures formed by individual adsorption and coadsorption of Mn and Bi on Cu(0 0 1), studied by LEED

We have studied the individual adsorption of Mn and Bi, and their coadsorption on Cu(0 0 1) by low-energy electron diffraction (LEED). For Mn, we have determined the c(2 × 2) structure formed at 300 K, whose structure had been determined by several methods. We reconfirmed by a tensor LEED analysis that it is a substitutional structure and that a previously reported large corrugation (0.30 Å) between substitutional Mn and remaining surface Cu atoms coincides perfectly with the present value. In the individual adsorption of Bi, we have found a c(4 × 2) structure, which is formed by cooling below ∼250 K a surface prepared by Bi deposition of ∼0.25 ML coverage at 300 K where streaky half-order LEED spots appear. The c(4 × 2) structure has been determined by the tensor LEED analysis at 130 K and it is a substitutional structure. In the coadsorption, we found a c(6 × 4) structure, which has been determined by the tensor LEED analysis. It is very similar to the previously determined structure of the c(6 × 4) formed by coadsorption of Mg and Bi, and embedded MnBi₄ clusters are arranged in the top Cu layer instead of MgBi₄. Large lateral displacements of Bi atoms in the c(6 × 4)-(Mn + Bi) suggest that the Mn atoms undergo the size-enhancement caused by their large magnetic moment.     

Effect of the Parameters of Three-Mirror Resonators on the Spectral Characteristics of Single-Pulse Laser Generation with Self-Injection of Priming Radiation

Based on a semiclassical theory, investigations were made of the dynamics and spectral composition of pulsed generation with self-injection of priming radiation from the active part of a three-mirror linear resonator, the passive part of which contains an active loss modulator and serves as the output reflector of the laser. It is shown that there exists a range of resonator parameters at which pulsed lasing has virtually a single frequency irrespective of the detuning of the frequencies of the priming radiation and of the nearest eigenmode of the composite resonator. Considering graphically the phase conditions of generation, it is established that among pulsed lasers with self-injection of priming radiation which are constructed on the basis of three-mirror linear and branched resonators, the most efficient for creating single-frequency generation are those in which the length of the main resonator, where generation of the pulse occurs, is larger than the length of the additional one intended for forming the priming radiation. With an inverse ratio of the lengths of the resonators, the conditions of single-frequency pulsed generation becomes dependent on the priming radiation frequency.     

Electrical behavior of the Au/MoS2 interface studied by light emission induced by scanning tunneling microscopy

Light emitted in the tunneling junction of a scanning tunneling microscope has been used to establish the electrical characteristics of nanojunctions made of Au islands deposited on flat MoS₂ surfaces. It is shown that these characteristics are those of rectifying contacts when the gold islands are isolated and that they evolve toward those of ohmic contacts when the island density increases. It is observed that the rectifying behavior also evolves over time as on infinite metal/semiconductor contacts. Using the STM tip, single gold islands can be manipulated on the MoS₂ surface so that their electrical behavior can be changed depending on their position with regard to the other islands.