In this paper we consider a special optimization problem withtwo objectives which arises in antenna theory. It is shown that thisabstract bicriterial optimization problem has at least one solution.Discretized versions of this problem are also discussed, and therelationships between these finite dimensional problems and the infinitedimensional problem are investigated. Moreover, we presentnumerical results for special parameters using a multiobjectiveoptimization method. 相似文献
In this paper, we have developed a load-bearing outer skin for antennas, which is termed a composite smart structure (CSS). The CSS is a multilayer composite sandwich structure in which antenna layers are inserted. A direct-feed stacked patch antenna is considered. A design procedure including the structure design, material selection, and design of antenna elements in order to obtain high electric and mechanical performances is presented. An optimized honeycomb thickness is selected for efficient radiation and impedance characteristics. High gain conditions can be obtained by placing the outer facesheet in the resonance position, which is at about a half wavelength distance from the ground plane. The measured electrical performances show that the CSS has a great bandwidth (over 10%) and a higher gain than an antenna without a facesheet and has excellent mechanical performances, owing to the composite laminates and honeycomb cores. The CSS concept can be extended to give a useful guide for manufacturers of structural body panels and for antenna designers. 相似文献
This paper presents an active patch array designed at 24 GHz. It can be used as a front-end component for a phased array. A series resonant array structure is chosen which is compact and easy excite. With 5 elements, the array proved a 12-dB antenna gain. A power amplifier and a low noise amplifier are designed on a single GaAs chip (PALNA). Bias switch is used in the PALNA, which greatly reduces the switch loss in a transceiver and increases the efficiency. 20-dB small signal gain is achieved in both power amplifier and low noise amplifier. The active patch array is built by the combination of the patch array and PALNA. The measured active gain of this antenna is 35-dB for the PA mode and 31-dB for the LNA mode. This active patch array can obtain an EIRP of 34 dBm with a total radiated power of 22dBm and a maximum PAE of 32%. To check the noise performance, we applied sources at both normal temperature and 77K (liquid nitrogen) and extracted the noise figure (3.5 dB) of the active antenna by the Y factor method. The results proved that the active antenna is working efficiently as both a transmitting and receiving antenna. 相似文献
We report on various integration schemes of infrared microbolometers with microstrip antennas. The first integration design consists of two gold (Au) rectangular microstrip patches coupled along the radiating edges by a narrow niobium (Nb) strip. Devices using silicon oxide are compared to devices using amorphous silicon as antenna substrate. An extension of the twin-patch detector design is the microstrip dipole antenna-coupled microbolometer. Two ways of connecting the device to the contact pads via narrow dc leads are presented and compared. The contribution of the dc leads to the detector response is eliminated by directly connecting the dipole to the contact pads. The thermal isolation of the microbolometer from the silicon wafer is improved by incorporating air into the antenna dielectric substrate. This leads to higher detector responsivity and shifts the resonance towards longer antennas. The implementation of a bridge microstrip dipole antenna structure is also discussed. 相似文献
This paper describes numerical modelling of a dual band multi-layered microstrip patch antenna operating at 35GHz on an in-house semi-insulating GaAs substrate. The simulated and measured resonant frequencies at both lower and upper resonant frequencies will be compared to check the accuracy of the different numerical modelling techniques. 相似文献
Despite the great promise of printed flexible electronics from 2D crystals, and especially graphene, few scalable applications have been reported so far that can be termed roll‐to‐roll compatible. Here we combine screen printed graphene with photonic annealing to realize radio‐frequency identification devices with a reading range of up to 4 meters. Most notably our approach leads to fatigue resistant devices showing less than 1% deterioration of electrical properties after 1000 bending cycles. The bending fatigue resistance demonstrated on a variety of technologically relevant plastic and paper substrates renders the material highly suitable for various printable wearable devices, where repeatable dynamic bending stress is expected during usage. All applied printing and post‐processing methods are compatible with roll‐to‐roll manufacturing and temperature sensitive flexible substrates providing a platform for the scalable manufacturing of mechanically stable and environmentally friendly graphene printed electronics.