Numerical solutions of the shallow water equations with discontinuous bed topography

A simple scheme is developed for treatment of vertical bed topography in shallow water flows. The effect of the vertical step on flows is modelled with the shallow water equations including local energy loss terms. The bed elevation is denoted with z_b^‐ for the left and z_b⁺ for the right values at each grid point, hence exactly representing a discontinuity in the bed topography. The surface gradient method (SGM) is generalized to reconstruct water depths at cell interfaces involving a vertical step so that the fluxes at the cell interfaces can accurately be calculated with a Riemann solver. The scheme is verified by predicting a surge crossing a step, a tidal flow over a step and dam‐break flows on wet/dry beds. The results have shown good agreements compared with analytical solutions and available experimental data. The scheme is efficient, robust, and may be used for practical flow calculations. Copyright © 2002 John Wiley & Sons, Ltd.     

Some hydrodynamic aspects of 3-phase inverse fluidized bed

Hydrodynamics of 3-phase inverse fluidized bed is studied experimentally using low density particles for different liquid and gas velocities. The hydrodynamic characteristics studied include pressure drop, minimum liquid and gas fluidization velocities and phase holdups. The minimum liquid fluidization velocity determined using the bed pressure gradient, decreases with increase in gas velocity. The axial profiles of phase holdups shows that the liquid holdup increases along the bed height, whereas the solid holdup decreases down the bed. However, the gas holdup is almost uniform in the bed.     

造纸污泥与废水污泥流化床焚烧时NO_x和SO_2的排放特性研究

1前言流化床焚烧污犯是近年来发达国家广泛采用的方法，它能很好地实现污泥的稳定化、无害化、减容化和资源化处理。燃煤流化床锅炉污染物排放方面已做了大量的研究工作，由于污泥与煤在结构和性质方面的差异较大，因此有必要对流化床焚烧污泥时污染物排放特性进行研究。本文详细研究了造纸、废水污泥在流化床中焚烧时污泥水份、运行床温及过量空气对NO。和SO。的排放特性及污泥N－＋NO。、S－SO。的转化率的影响，并对这两种性质差异较大的污泥焚烧时的NO。和502的生成特性进行了对比分析，取得了许多有价值的结果，为污泥流化床焚烧…     

气-固流化床反应器内双流体力学模型及其验证 Ⅱ.单组分两维射流床内流场特性分析

由以质量、动量和能量三大守恒定律为基础的湍流两相流理论出发,建立了描述气固流化床内两相流动的数学模型;在微型计算机上编写了相应的数值计算和图形处理程序;为了验证模型的可靠性,本文着手模拟与分析了单组分颗粒体系两维射流流化床内气、固相速度场、空隙度和压力场随时间、空间变化规律;得到了与前人实验结果相吻合的结论。     

不同常压流化床煤气化方案的模型预测 Ⅰ. 模型建立及验证

为评价不同气化方案对常压流化床气化的影响，从化学动力学角度并结合化学平衡建立了流化床气化模型，该模型考虑了煤热解和气化所经历的各反应过程。模型预测结果与文献报道的试验数据吻合较好，气化组分的平方误差和在10%左右，表明该模型可以用来预测各种气化方案对常压流化床气化的气化过程、生成煤气组分和气化效率等方面的影响。     

Influence of particle diameter distribution on protein recovery in the expanded bed adsorption process

The General Rate model has been developed and solved to describe protein adsorption in an expanded bed. The model takes into account axial and local variation of particle size distribution (PSD), external and intra-particle mass transfer resistances, and dispersion in liquid phase. The influence of PSD on breakthrough profiles has been analysed. The simulation results show that for a significantly high expanded bed the lower part of the breakthrough curve profiles, calculated for local particle size distribution (LPSD) and for axial average particle size distribution (APSD) are very similar. However, the upper part of breakthrough profiles calculated for LPSD approaches inlet concentration much more slowly than those calculated for APSD. The retention times of the lower part of uptake curves calculated with average particle diameter are constantly shorter than those obtained from LPSD. For the calculation of the dynamic capacity (DC), the LPSD can be replaced by APSD for large expanded bed heights. Using breakthrough profiles calculated for average particle size, DC values are constantly underestimated.     

循环流化床生物质气化炉内计算流体动力学模拟——鼓泡流化床内改进的颗粒床模型（英文）

采用改进颗粒床模型的CFD方法模拟了实验室规模冷模装置内鼓泡床的流体流动时空特性。模拟结果表明表观气速是影响气固动态特征和压力波动的主要因素之一：随表观气速的增大，气泡数目增加，气泡体积增大，压力波动增强；气速越高时均压降越大；在内循环鼓泡流化床内固体颗粒呈“单室”流型。上述与实验观察相吻合的模拟结果将有助于放大和设计商业化的内循环流化床生物质气化炉。     

生物质在流化床中的空气-水蒸气气化研究

以流化床为反应器，对生物质的空气-水蒸气气化特性进行了研究。考察了一些主要参变量，如温度 (700 ℃～900 ℃)、水蒸气/生物质比(0～4.04)、空气当量比(0.19～0.27)以及生物质粒度(0.2 mm～0.9 mm)等对气化结果的影响。在实验研究的条件范围内，生物质产气率在1.43 m3/kg～2.57 m3/kg范围内变化，产气的低热值在6 741 kJ/m3～9 143 kJ/m3范围内变化。实验结果表明：较高的气化温度有利于氢的产生；但气化温度过高会使气体热值下降；与常规的空气气化相比，水蒸气的加入使生物质气化产气率显著提高，但水蒸气加入量过多使气化温度下降，产气率和产气热值降低；生物质颗粒粒度的大小对产气组分的分布和产气率均有影响，较小颗粒的生物质会产生较多的CH4、CO和较少的CO2。     

正丁烷氧化制顺酐流化床催化剂的性能

 考察了前驱体制备过程中水合肼／五氧化二钒摩尔比（以下简记\r\n为n（N2H4）／n（V2O5））对催化剂性能的影响．由较高的n（N2H4）\r\n／n（V2O5）比制得的催化剂，其（VO）2P2O7相含量较多，正丁烷转化\r\n率较高．随着n（N2H4）／n（V2O5）比的减小，δ－VOPO4相的含量逐\r\n渐增多，正丁烷转化率随之升高；而顺酐选择性开始时升高，达到最大\r\n值后逐渐降低．在n（N2H4）／n（V2O5）＝0．34时制备的催化剂最佳\r\n，在丁烷浓度为4．0％、空速为500h－1及反应温度为420℃的反应条件\r\n下，顺酐收率可达49．74％．本文中细粒床催化剂有较大的操作弹性．     

用于流化床燃烧脱硫的石灰石的反应活性评价和测试研究

对用于燃煤流化床燃烧脱硫的脱硫剂石灰石的反应活性进行了研究，提出了易于进行数学处理的石灰石硫盐化模型，得出了评价石灰石反应活性的两个指标－最大转化率和反应速率常数。研究方法除采用了传统的热天平法和鼓泡流化床外，还根据循环流化床燃烧技术的特点，发展了提出了湍流床法和石英棉法，并进行了不同试验条件下的实验研究，对不同反应活性温度技术进行了试验比较。