Deposition of boron nitride on graphite at 1300 K

A method for the deposition of BN onto graphite and other substrates is described. Boron trichloride (BCl₃) and ammonia (NH₃) diluted with Ar were used as reacting gases. The deposition process was carried out at 1300 K as well as lower temperatures in an open system at pressures of 1 atm. The consequences of the introduction of hydrogen to the system were considered. It was demonstrated that the replacement of argon with hydrogen increases the efficiency of the process as well as the theoretical rate of BN deposition. However, the acceleration of the deposition seems to be unprofitable, because the resulting supersaturation leads to the formation of an amorphous phase. The modification of the experimental conditions were proposed.Dedicated to Professor Dr. rer. nat. Dr. h.c. Hubertus Nickel on the occasion of his 65th birthday     

Rb（5PJ）＋Rb（5PJ）→Rb（5JS）＋Rb（nl=5D，7S）碰撞能量合并

研究了Rb(5PJ)+Rb(5PJ)→Rb(nlJ')+Rb(5S)碰撞能量合并过程,利用单模半导体激光器分别共振激发Rb原子的5P1/2或5P3/2态,利用另一与泵浦激光束反向平行的单模激光束作为吸收线探测激发态原子密度及其空间分布,吸收线分别调至5P1/2→5D3/2和5P3/2→7S1/2跃迁.由激发态原子密度和谱线荧光比得到碰撞能量合并过程的截面,对5P3/2激发,碰撞转移得到5D5/2,5D3/2和7S1/2的截面分别是(1.32士0.59)×10-14,(1.18士0.53)×10-14和(3.21士1.44)×10-15cm2;对5P1/2激发,碰撞转移到5D5/2和5D3/2的截面分别是(6.57士2.96)×10-15和(5.90士2.66)×10-15cm2.与其他的实验结果进行了比较.     

Anomalies of attenuation and phase velocity of surface acoustic waves in YBa2Cu3O7‒δ thin films in the vicinity of Tc

We present measurements of the attenuation and phase velocity of surface acoustic waves in thin YBa₂Cu₃O films as a function of temperature, in magnetic fields up to 3.6 T applied parallel to the c-axis of the films. We have observed anomalies in both, the attenuation and the phase velocity in the vicinity of the superconducting critical temperature which do not depend on the magnetic field. Possible origins of these anomalies, observed, to our knowledge, for the first time in YBa₂Cu₃O thin films, are discussed and compared to bulk acoustic wave experiments. We present a kind of feedback technique for surface acoustic waves which improves the sensitivity of this type of measurement. The actual sensitivity limits are mentioned. Received: 7 August 1997 / Revised: 7 November 1997 / Accepted: 17 November 1997     

固体样品进样技术中汞量定标方法的研究

在原子吸收光谱分析中,固体样品直接进样是目前的研究课题之一。本文主要报道作者在分析汞中所进行的固体直接进样技术工作和讨论。在我们研制成功的KT—81型塞曼效应测汞仪中,针对元素汞蒸气压高的特点,用饱和汞蒸气作为汞量标准,实现了固体样品,如土壤、污泥、毛发、煤、食品等汞含量的直接进样测定。汞蒸气一次制备后可长期使用。分析汞时,只要用标准气体任意校验一次就可测量。1～2分钟能分析一个样品,S<0.3ng。r<5%。此法用NBS标准物质验证过。     

化学蒸气沉积硅氧化合物调变HZSM－5沸石的研究

本文研究了正硅酸乙酯分别在无胺法和有胺法制得的ＨＺＳＭ－５沸石上的沉积过程，并用吸附，ＮＨ３－ＴＰＤ及异丙醇探针反应等手段表征了沉积后的样品，发现沉积仅在外表面上进行，可使孔口变小但不影响孔道内性质，显示有对于二甲苯分子的择形吸附能力，且在甲苯甲醇烷基化反应和二甲苯异构化反应中表现出良好的择形催化性能．     

Comments on surface structure analysis by water and nitrogen adsorption

Specific surface area and pore size distribution are determined usually from adsorption isotherms at low temperatures using nitrogen or noble gases. These are not absolute parameters and the measuring methods are fraught with serious difficulties. General problems of sorption measurements and recent developments are discussed. To obtain information for practical purposes these measurements need to be supplemented by investigations of the sorbate/sorbent system used in practice. Results of the measurement of nitrogen and water vapour adsorption on different materials are compared. This revised version was published online in July 2006 with corrections to the Cover Date.     

Determination of total mercury in environmental and biological samples by flow injection cold vapour atomic absorption spectrometry

A simple and accurate method has been developed for the determination of total mercury in environmental and biological samples. The method utilises an off-line microwave digestion stage followed by analysis using a flow injection system with detection by cold vapour atomic absorption spectrometry.

The method has been validated using two certified reference materials (DORM-1 dogfish and MESS-2 estuarine sediment) and the results agreed well with the certified values. A detection limit of 0.2 ng g⁻¹ Hg was obtained and no significant interference was observed. The method was finally applied to the determination of mercury in river sediments and canned tuna fish, and gave results in the range 0.1–3.0 mg kg⁻¹.     

Methyl cellulose-based edible films and coatings I. Effect of plasticizer content on water and 1-octen-3-ol sorption and transport

Edible films were prepared from methyl cellulose with various concentrations of poly(ethylene glycol) 400 (PEG400) used as a plasticizer. Water vapour and 1-octen-3-ol (an aroma compound) were selected as hydrophilic and hydrophobic volatile penetrants respectively. Their solubility and permeability through methyl cellulose-based edible films were studied using gas chromatography methods. Whatever penetrant was used, the flux increased with the PEG400 content. Transfer behaviour, i.e., the order of increased magnitude of the transfer rate, strongly depends on the nature of the volatile compound. However, water sorption only depends on the PEG400 content whereas the aroma compound sorption is affected by both the water and the PEG400 concentrations. Relationships between solubility and permeability can be partially explained by the plasticization phenomenon.     

Acetylation and molecular mass effects on barrier and mechanical properties of shortfin squid chitosan membranes

Chitosan samples with different N-deacetylation levels were obtained from β-chitin under heterogeneous alkali conditions. Oxidative depolymerisation was performed to attain low-acetylated chitosan samples with different molecular mass. Water vapour permeability, membrane swelling and tensile mechanical properties were analysed in plasticized self-supporting chitosan membranes. The main purpose was to describe unambigously the effect of the biopolymer molecular mass and acetylation degree on these properties. Commercially available chitosan samples derived from α-chitin were also studied for comparison. The equilibrium degree of swelling in water and the water vapour permeability increase by increasing the molecular mass or the degree of acetylation. Regarding the effect on the mechanical properties, generally harder and tougher membranes were obtained for chitosans with higher molecular mass or lower acetylation degree. These observations are tentatively explained based on the different structural characteristics of the polymer and can lead to a better understanding of the tools necessary to tailor a specific type of chitosan membrane.     

溶剂蒸气对聚对苯二甲酸乙二酯作用的差示扫描量热研究

用差示扫描量热(DSC)研究了几种有机溶剂蒸气对聚对苯二甲酸乙二酯(PET)的作用,表明可分为反应性的和非反应性的两种。同时,对于非反应性的作用,依冷结晶峰面积的变化,又可分为三种类型:冷结晶峰面积不变,经诱导期后下降,无诱导期而迅速下降。双冷结晶峰现象在一些非反应性溶剂处理过的PET试样的DSC曲线也观察到。