Effect of chemical parameters on pyrene degradation in soil in a pulsed discharge plasma system

Degradation of pyrene in soil in a net-to-net pulsed discharge plasma (PDP) system was reviewed. Effect of main chemical parameters, including air flow rate, pyrene concentration, initial pH and soil moisture content on pyrene degradation was examined. The obtained results show that 87.9% of pyrene could be removed under the condition of 60 min reaction; increasing of air flow rate within 1 L min⁻¹ was favorable for degradation; pyrene removal was decreased with the increase of initial pyrene concentration; oxidation of pyrene was more evident in acidic soil; enhancement of soil moisture content has no benefit on pyrene degradation.     

Elongating the area of plasma/fluid interaction of surface nanosecond pulsed discharges

Plasma-assisted flow control is of high industrial interest, but practical applications at full scale require a large surface of interaction. Nanosecond pulsed Dielectric Barrier Discharge (DBD) have demonstrated promising results of flow control, but their interacting region is limited to only a few cm². In this paper, the conditions to extend a surface nanosecond DBD are documented. It is shown that a sliding discharge regime can fully fill an inter-electrode distance of 40 mm. This discharge regime promotes the formation of two hemispheric pressure waves originating from both air-exposed electrodes while an horizontal region of pressure gradient is also observed.     

Quantum states in fabricating poly-Si films

The quantum states are presented in these processions of fabricating poly-Si films. Amorphous silicon films prepared by PECVD has been crystallized by conventional furnace annealing (FA) and rapid thermal annealing (RTA), respectively. It is found that the thin films grain size present quantum states with the increasing of the gas flow ratios of SiH₄, H₂ mixture, substrate temperatures, frequency power, annealing temperature and time.     

Active long pulse shaping technique of pulsed CO2 laser using multi-pulse discharge control

We describe the pulse forming of pulsed CO₂ laser using multi-pulse superposition technique. Various pulse shapes, high duty cycle pulse forming network (PFN) are constructed by time sequence. This study shows a technology that makes it possible to make various long pulse shapes by activating SCRs of three PFN modules consecutively at a desirable delay time with the aid of a PIC one-chip microprocessor. The power supply for this experiment consists of three PFN modules. Each PFN module uses a capacitor, a pulse forming inductor, a SCR, a high voltage pulse transformer, and a bridge rectifier on each transformer secondary. The PFN modules operate at low voltage by driving the primary of HV pulse transformer. The secondary of the transformer has a full-wave rectifier, which passes the pulse energy to the load in a continuous sequence.We investigated various long pulse shapes as different trigger time intervals of SCRs among three PFN modules. As a result, we could obtain laser beam with various pulse shapes and durations from about 250 to 1000 μs.     

Polytetrafluoroethylene and metal structure convective-flow CO laser

A convective flow CO laser composed of polytetrafluoroethylene discharge tubes, nickel–chromium steel components, a cupric heat exchanger and other components is described. Operating in liquid nitrogen condition, output power of 60 W has been obtained from a non-selective cavity.     

Fabrication and characterization of a PbTe quantum dots multilayer structure

Multilayer PbTe quantum dots (QDs) and SiO₂ were grown by pulsed laser deposition (PLD) and Plasma enhanced chemical vapor deposition (PECVD) techniques. The crystalline structure, QD size and size dispersion were observed by high-resolution transmission electron microscopy (HRTEM) measurements. This technique allows one to grow PbTe QDs as small as 1.8 nm diameter and 0.6 nm size dispersion. The whole structure can be used in a Fabry–Perot cavity for an optical device operating at the mid-infrared region.     

采用空心阴极放电等离子体化学气相沉积方法制备a-CH薄膜

 研究了不同衬底-阴极距离、直流电压和H₂流量对a-CH薄膜沉积速率的影响。结果表明：衬底-阴极距离必须大于0.5cm，随着该距离的增加，薄膜的沉积速率减少；直流电压达550V时沉积速率最大；随着H2含量的增加，CH₄含量相对减少，沉积速率随之降低。用AFM观察了以该方法制得的448.4nm CH薄膜的表面形貌，表面粗糙度约为10nm。最后测出了不同条件下CH薄膜的UV-VIS谱，由此可以计算得到薄膜的禁带宽度及折射率。     

利用爆磁压缩发生器产生高功率脉冲高电压

 爆磁压缩发生器产生脉冲高电压技术可以用于产生高功率微波及强电磁脉冲的实验研究。给出了利用螺旋型爆磁压缩发生器（HEMG）驱动电爆炸丝功率调节系统产生高功率脉冲高电压的实验方法和主要的结果。在利用HEMG驱动电爆炸丝断路开关（EEOS）产生脉冲高电压实验中，获得了最高电压700~800kV,功率大于20GW的脉冲输出。     

超短脉冲贝塞尔光束的非近轴效应对传输的影响

 对超短脉冲贝塞尔光束在近轴近似和非近轴情况下自由空间中的传输作了研究。结果表明，其空间波形在传输中保持贝塞尔形状不变，不受非近轴效应影响；然而当空间参数较大时，非近轴效应影响超短脉冲贝塞尔光束的时间波形。     

用于激光推进的高功率激光器的选择

 从激光推进的要求出发，阐述了用于激光推进的高功率激光器的选择原则，即激光器必须满足：（1）高的平均功率和峰值功率；（2）高的单脉冲能量；（3）高的重复频率；（4）优良的大气传输特性。主要分析了目前YAG固体激光器、自由电子激光器和TEA脉冲CO₂激光器的特点，通过上述4个方面性能的比较，认为在目前水平下，TEA脉冲CO₂激光器是进行激光推进的首选强激光源，其优点表现在：功率可达10kW量级，单脉冲能量可达0.5~1kJ，重复频率为20~40Hz；激光波长处于大气传输窗口，对大气变化不敏感；工作物质快速流动，不存在热透镜效应和破坏阈值；相关光学元件易于制造；光束质量较好；运行成本低。