Influence of Cd and Cr substitutions on the magnetization and permeability of magnesium ferrites

Magnetization and permeability of polycrystalline ferrites with general formula Cd_xMg_1−xFe_2−yCr_yO₄ (x=0, 0.2, 0.4, 0.6, 0.8, 1.0; y=0, 0.05 and 0.10) were studied. Study of saturation magnetization reveals that the Neel's two-sublattice model exists upto x=0.4, for y=0, 0.05 and 0.1 and a three-sublattice model (YK-model) is predominant for x>0.4 and y=0, 0.05 and 0.10. The saturation magnetization and magnetic moment were found to decrease with the increase in Cr³⁺ contents, which is attributed to the dilution of B–B site interaction. Variation of initial permeability with temperature revealed the long-range ferromagnetic ordering in the compounds with x=0.4. The sample with x?0.4 and y=0, 0.05 and 0.10 showed peaking behavior near Curie temperature, which is attributed to the decrease of anisotropy constant K₁ to zero. Low-frequency dispersion of initial permeability suggests domain wall displacement. Addition of Cd²⁺ resulted in a sharp decrease in Curie temperature. With the addition of Cr³⁺, initial permeability was found to decrease.     

Suppression of red cell diffusional water permeability by lipophilic solutes

The inhibitory effect of a series of neutral lipophilic solutes (methanol, ethanol, n-propanol, iso-propanol, n-butanol, iso-amylalcohol, n-hexanol, diethylether, nitrobenzene, and pyridine) on the diffusional water permeability (Pd, tot) of bovine erythrocyte membrane at 25 degrees C was studied in comparison to that of p-chloromercuri benzoate (pCMB). Permeability data were obtained by measuring the transmembrane diffusional water exchange time tau(exch) using an 1H-T2 NMR technique. Maximal inhibition by approximately 50% of Pd, tot was produced by 2 mM pCMB which completely blocked the membrane water channels in 20 min, hence suggesting the channel-to-lipid diffusional water permeability ratio of about 1:1. Furthermore, the maximal inhibitory effect of pCMB in combination with the lipophilic solutes was lower than that of pCMB alone. As pCMB does not interfere with the lipid bilayer, and provided that it blocks the water channels in solute presence as well, this confirms that the solutes induce an increase in the lipid-mediated background water permeability contribution (Pd, lipid) by the formation of aqueous leaks in the membrane hydrophobic barrier. However, faster but less efficient in permeability inhibition than pCMB (either alone or combined with solutes) were the lipophilic solutes alone. Taken together, the results indicate that the lipophilic solutes suppress the membrane total permeability Pd, tot by two opposing effects: a reduction of its channel-mediated part (Pd, channel) to the extent exceeding that of a simultaneous Pd, lipid increase. The inhibitory potency of the solutes tested appears to be correlated with their solubility in the membrane medium.     

Dielectric,magnetic and mechanical properties of ferrite composites

The dielectric and magnetic properties of carbonyl—iron (CI) and nickel zinc ferrite polymer composites were studied with respect to the ferrite particulate content and microwave frequency. From the experimental data and using empirical models that relate the composite dielectric and magnetic properties, the respective dielectric and magnetic properties of the neat fillers were estimated. The tensile properties of the particulate composites comprising CI were shown to follow qualitatively Mooney's equation for the elastic modulus. The tensile strength of an elastomeric polyurethane and PVC composites containing CI increased with particulate content, while the elongation to break decreased with filler content. SEM micrographs of tensile fracture surfaces indicated that somewhat better adhesion is obtained in the case of the polyurethane-based composites compared to the PVC ones.     

联苯二酐型聚酰亚胺的透气性能与分子结构关系的研究

联苯二酐型聚酰亚胺的透气性能与分子结构关系的研究李悦生，丁孟贤，徐纪平（浙江大学高分子科学与工程研究所，杭州，３１００２７）（中国科学院长春应用化学研究所）关键词聚酰亚胺，膜，气体分离，透气性，透气选择性联苯二酐（ＢＰＤＡ）型聚酰亚胺具有较高的透气选...     

An NMR study of methanol diffusion in polymer electrolyte fuel cell membranes

Methanol diffusion in two polymer electrolyte membranes, Nafion 117 and BPSH 40 (a 40% disulfonated wholly aromatic polyarylene ether sulfone), was measured using a modified pulsed field gradient NMR method. This method allowed for the diffusion coefficient of methanol within the membrane to be determined while immersed in a methanol solution of known concentration. A second set of gradient pulses suppressed the signal from the solvent in solution, thus allowing the methanol within the membrane to be monitored unambiguously. Over a methanol concentration range of 0.5–8 M, methanol diffusion coefficients in Nafion 117 were found to increase from 2.9 × 10⁻⁶ to 4.0 × 10⁻⁶ cm² s⁻¹. For BPSH 40, the diffusion coefficient dropped significantly over the same concentration range, from 7.7 × 10⁻⁶ to 2.5 × 10⁻⁶cm² s⁻¹. The difference in diffusion behavior is largely related to the amount of solvent sorbed by the membranes. Increasing the methanol concentration results in an increase in solvent uptake for Nafion 117, while BPSH 40 actually excludes the solvent at higher concentrations. In contrast, diffusion of methanol measured via permeability measurements (assuming a partition coefficient of 1) was lower (1.3 × 10⁻⁶ and 6.4 × 10⁻⁷ cm² s⁻¹ for Nafion 117 and BPSH 40 respectively) and showed no concentration dependence. The differences observed between the two techniques are related to the length scale over which diffusion is monitored and the partition coefficient, or solubility, of methanol in the membranes as a function of concentration. For the permeability measurements, this length is equal to the thickness of the membrane (178 and 132 μm for Nafion 117 and BPSH 40 respectively) whereas the NMR method observes diffusion over a length of approximately 4–8 μm. Regardless of the measurement technique, BPSH 40 is a greater barrier to methanol permeability at high methanol concentrations.     

Morphology and transport properties of protons and methanol through partially sulfonated block copolymers

The morphological changes with different compositions of casting solvents in the membranes of sulfonated polystyrene-block-poly(ethylene-ran-butylene)-block-polystyrene (SEBS) were investigated with small-angle X-ray scattering (SAXS) and transmission electron microscope (TEM). Using the single solvent of tetrahydrofuran (THF) and the solvent mixtures of methanol/THF with different compositions, the casting polymer solutions were prepared for the membrane fabrication. The proton conductivity and the methanol permeability of membranes were measured, and the effect of morphological changes on the casting solvents was discussed through Flory–Huggins theory. It was found that the sulfonated SEBS membranes were transformed from well ordered lamellar to disordered co-continuous structure and the morphological difference caused abrupt enhancement in the proton conductivity and the methanol permeability as the concentration of methanol in the mixed solvents (MeOH/THF) increased.     

SYNTHESIS AND CHARACTERISTICS OF POLY(ARYLENE ETHER DIKETONE)S

Poly(arylene ether diketone)s were prepared by the aromatic nucleophilicdisplacement reaction of 4,4'-difluorobenzil with different bisphenols in the presence of an-hydrous potassium carbonate in diphenylsulfone at elevated temperature. The polymersobtained had inherent viscosity of 0.51 ～ 0.63 dL/g, and exhibited glass transition temper-ature ranging from 136 ～217℃ mainly depending on the bisphenols used in the polymersynthesis. Thermogravimetry of these polymers showed excellent thermal stability, indi-cating that 10% weight losses of the polymers were observed in the range above 428℃ and438℃ in air and nitrogen, respectively. The mechanical properties of these polymers werealso described and the permeability of five polymers for H_2, O_2 and N_2 was determined at30℃.     

Permeability of microscale fibrous porous media using the lattice Boltzmann method

The permeabilities of microscale fibrous porous media were calculated using the multiple-relaxation-time (MRT) lattice Boltzmann method (LBM). Two models of the microscale fibrous porous media were constructed based on overlapping fibers (simple cubic, body-centered cubic). Arranging the fibers in skew positions yielded two additional models comprising non-overlapping fibers (skewed simple cubic, skewed body-centered cubic). As the fiber diameter increased, the fibers acted as granular inclusions. The effects of the overlapping fibers on the media permeability were investigated. The overlapping fibers yielded permeability values that were a factor of 2.5 larger than those obtained from non-overlapping fibers, but the effects of the fiber arrangement were negligible. Two correlations were obtained for the overlapping and non-overlapping fiber models, respectively. The effects of the rarefaction and slip flow are also discussed. As the Knudsen number increased, the dimensionless permeability increased; however, the increase differed depending on the fiber arrangement. In the slip flow regime, the fiber arrangement inside the porous media became an important factor.     

Cross‐linked Multilayer Polymer‐Clay Nanocomposites and Permeability Properties

Abstract

Electrostatically layered aluminosilicate nanocomposites have been prepared by the sequential deposition of poly(allylamine hydrochloride)/poly(acrylic acid)/poly(allylamine hydrochloride)/saponite (PAH/PAA/PAH/saponite)₁₀ on poly(ethylene terephtalate) (PET) film. Exfoliated saponite nanoplatelets were obtained by extensive shaking, sonication, and centrifugation of a water suspension. To minimize permeability and improve the mechanical integrity, cross‐linking of composite films was carried out at different temperatures. The formation of amide linkage induced through heating was observed by Fourier Transform Infrared (FT‐IR) and x‐ray photoelectron spectroscopy (XPS). The cross‐linking of nanocomposites (PAH/PAA/PAH/saponite)₁₀ showed 60% decrease in permeability of oxygen when compared with the pristine PET substrate film. In contrast, water permeability of the nanocomposite membrane was not affected by heating temperature and deposition cycles.     

Bio-silica incorporated barium ferrite composites: Evaluation of structure,morphology, magnetic and microwave absorption traits

A series of bio-silica incorporated barium-ferrite-composites with the composition of (x)Bio-SiO₂:(80-x)γ-Fe₂O₃:(20)BaO, where x = 0, 1, 2, and 3 wt% were prepared using the modified solid-state reaction method. The influence of different bio-silica (extricated from sintered rice husk) contents on the surface morphologies, structures, and magnetic characteristics of these composites were assessed. The relative complex permittivity and permeability were resolved using the Nicholson-Ross-Weir strategy in the frequency range of 8–13 GHz. Meanwhile, the reflection loss was estimated through the transmission/reflection line theory to assess the MW absorption properties of the composites. Incorporation of the bio-silica in the barium ferrite composites generated a new hexagonal phase (Ba₃Fe₃₂O₅₁) and a tetragonal phase (BaFeSi₄O₁₀) which led to a decrease in the saturation magnetization and significant shift in the MW frequency absorption peak positions.