Synthesis of Cationic PEM Emulsion and Application in Waste Water Treatment

Cationic polymer as a kind of flocculant is widely applied in purification treatment of waste water. Because it has positive charge group, it is able to connect strongly the suspended matters, short cellulose and other microparticles. The research on synthesis of cationic polymer and application in treatment of waste water is very universal abroad. But domestic research on those is not general. The technology of synthesis of PEM is simple, and the production cost is low. It is easy to apply in treatment of waste water.Synthesis of PEM Emulsion FlocculantSome distilled water, PVA(poly(vinyl alcohol)), EA(ethyl acrylate), and K2S2O8(potassium persulfate) were put into reaction vessel. Kept stirring up under nitrogen. When heated the solution to 40℃, dropped the water solution of MTA[(2-methacryloxylethyl)trimethyl ammonium].Maintained the temperature at 70℃, reacted about 7-8 hours. Then got the PEM emulsion. Changed the ratio of EA and MTA. Obtained a series of PEM emulsions.Stability and Convertibility of PEM EmulsionThe test results showed that when the EA/MTA was 85/15, the PEM emulsion was most stable.When the total monomer quantity was 35%, the convertibility of PEM emulsion was the highest,i.e.98.6%.The MTA Copolymerization Ratio and Morphology of PEM EmulsionWhen the monomers EA/MTA=85/15 and total monomer quantity was 35%, the MTA copolymerization ratio of PEM emulsion was 95.15%(the highest), and the PEM emulsion was some microspheres with 100-180nm of diameter.The Test Results of PEM Emulsion in Treatment of Waste Water The PEM emulsion flocculant was applied in treatment of waste water of paper mill, and measured the precipitation time(t) and transmittancy(T). The test results were showed in table 1. The optimum value of PEM which was able to make the waste water of paper mill into clear water was 0.008%.     

Embedded polymerization driven asymmetric PEM for direct methanol fuel cells

This work reports the fabrication of proton exchange membranes (PEM) with stronger resistance to methanol penetration than Nafion^®117. A three-component acrylic polymer blend (TCPB) consisting of a copolymer of 4-vinylphenol-methyl methacrylate, poly(butyl methacrylate) (PBMA) and a copolymer of methyl methacrylate-ethyl acrylate is used as the methanol barrier. In order to implant a proton source phase within the membrane as homogeneously as possible, the hydrophilic monomers, 2-acrylamido-2-methyl propanesulfonic acid (AMPS), 2-hydroxyethyl methacrylate (HEMA) and poly(ethylene glycol) dimethylacrylate (PEGDMA), are polymerized only after they have been embedded in the TCPB matrix. The embedded polymerization has resulted in an asymmetric membrane structure, in which the hydrophilic network is sandwiched by two layers of matrixes with high percentages of TCPB. As expected, this asymmetric membrane structure exhibits lower methanol uptake than Nafion^®117; and a proton conductivity in the range of 10⁻³–10⁻⁴ S/cm, which is dependent on the concentration of the sulfonic acid content. It is suggested that the two external layers in this asymmetric membrane provide primarily methanol-blocking and supporting proton-conducting properties; while the middle layer supplies protons and conserves water. This unique sandwiched PEM structure from embedded polymerization is confirmed by microstructure characterizations and by physical property measurements.     

Synthesis and characterization of SPE membrane based on sulfonated FEP‐g‐acrylic acid by radiation induced graft copolymerization for PEM fuel cell

A Novel solid polymer electrolyte (SPE) membrane containing both ? COOH and ? SO₃H group has been prepared by simultaneous method of radiation grafting of acrylic acid onto FEP followed by sulfonation. The presence of weakly acidic acrylic acid controls the swelling in water while ? SO₃H group provides conductivity due to its strongly ionic characteristic. FEP‐g‐acrylic acid and its sulfonated derivatives were characterized by their properties. While the mechanical properties decreased, other properties such as ion exchange capacity (IEC), water uptake and ionic conductivity increased with increase in graft content. These properties further changed on sulfonation. Acrylic acid being weakly acidic in nature, conductivity values of the grafted membrane were quite low. However, introduction of strong ? SO₃H group resulted in conductivity closer to Nafion 117. Few sulfonated membranes have been tested with respect to H₂/O₂ fuel cell performance. Short‐term fuel cell test for 100 hr gave a stable performance. These membranes are less expensive compared to Nafion. Copyright © 2004 John Wiley & Sons, Ltd.     

Current status of automotive fuel cells for sustainable transport

Automotive proton-exchange membrane fuel cells (PEMFCs) have finally reached a state of technological readiness where several major automotive companies are commercially leasing and selling fuel cell electric vehicles, including Toyota, Honda, and Hyundai. These now claim vehicle speed and acceleration, refueling time, driving range, and durability that rival conventional internal combustion engines and in most cases outperform battery electric vehicles. The residual challenges and areas of improvement which remain for PEMFCs are performance at high current density, durability, and cost. These are expected to be resolved over the coming decade while hydrogen infrastructure needs to become widely available. Here, we briefly discuss the status of automotive PEMFCs, misconceptions about the barriers that platinum usage creates, and the remaining hurdles for the technology to become broadly accepted and implemented.     

Dependence of CO oxidation on Pt nanoparticle shape: a shape‐selective approach to the synthesis of PEMFC catalysts

In real catalyst systems, it is difficult to establish a correlation between catalytic properties and the shape (crystal planes, corners and steps) of the active catalytic particles. In this paper we present a clear shape dependence of the catalytic properties of a Vulcan‐supported fuel cell catalyst having 4 nm cubo‐octahedral platinum(0) nanocrystallites with (111) and (100) surfaces stabilized by sodium polyacrylate. The electrode materials were characterized by CO‐stripping cyclic voltammetry and transmission electron microscopy (TEM), showing that no agglomeration had occurred among the nanoparticles on the catalyst surfaces. Copyright © 2007 John Wiley & Sons, Ltd.     

Characterizing fracture energy of proton exchange membranes using a knife slit test

Pinhole formation in proton exchange membranes (PEM) may be caused by a process of flaw formation and crack propagation within membranes exposed to cyclic hygrothermal loading. Fracture mechanics can be used to characterize the propagation process, which is thought to occur in a slow, time‐dependent manner under cyclic loading conditions, and believed to be associated with limited plasticity. The intrinsic fracture energy has been used to characterize the fracture resistance of polymeric material with limited viscoelastic and plastic dissipation, and has been found to be associated with long‐term durability of polymeric materials. Insight into this limiting value of fracture energy may be useful in characterizing the durability of proton exchange membranes, including the formation of pinhole defects. In an effort to collect fracture data with limited plasticity, a knife slit test was adapted to measure fracture energies of PEMs, resulting in fracture energies that were two orders of magnitude smaller than those obtained with other fracture test methods. The presence of a sharp knife blade reduces crack tip plasticity, providing fracture energies that may be more representative of the intrinsic fracture energies of the thin membranes. Three commercial PEMs were tested to evaluate their fracture energies (G_c) at temperatures ranging from 40 to 90 °C and humidity levels varying from dry to 90% relative humidity (RH). Experiments were also conducted with membrane specimens immersed in water at various temperatures. The time temperature moisture superposition principle was applied to generate fracture energy master curves plotted as a function of reduced cutting rate based on the humidity and temperature conditions of the tests. The shift with respect to temperature and humidity suggests that the slitting process is viscoelastic in nature. Also such shifts were found to be consistent with those obtained from constitutive tests such as stress relaxation. The fracture energy is more sensitive to temperature than on humidity. The master curves converge at the lowest reduced cutting rates, suggesting similar intrinsic fracture energies; but diverge at higher reduced cutting rates to significantly different fracture energies. Although the relationship between G_c and ultimate mechanical durability has not been established, the test method may hold promise for investigating and comparing membrane resistance to failure in fuel cell environments. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 333–343, 2010     

Determination of permeability in fibrous porous media using the lattice Boltzmann method with application to PEM fuel cells

The lattice Boltzmann method (LBM) is used to simulate the flow through an idealized proton exchange membrane fuel cell (PEMFC) porous transport layer (PTL) geometry generated using a Monte Carlo method. Using the calculated flow field, Darcy's law is applied and the permeability is calculated. This process is applied in both through‐ and in‐plane directions of the paper as both of these permeability values are important in computational fluid dynamics models of PEMFCs. It is shown that the LBM can be used to determine permeability in a random porous media by solving the flow in the microstructure of the material. The permeability in the through‐ and in‐plane directions is shown to be different and the anisotropic nature of the geometry creates anisotropic permeability. It is also found that fiber arrangement plays a large role in the permeability of the PTL. New correlations are presented for in‐ and though‐plane permeabilities of fibrous porous media with (0.6<ε<0.8). Copyright © 2008 John Wiley & Sons, Ltd.     

Numerical simulation of effects of flow maldistribution on heat and mass transfer in a PEM fuel cell stack

A 3D numerical study was carried out to analyze flow, heat and mass transfer first in a single half-cell cathode channel of proton exchange membrane (PEM) fuel cell. From practical point of view, it is necessary to put the appropriate number of cells in a stack. Hence, the above study on a single half-cell is extended to a stack of channels. Due to stacking, the assumption of uniform flow distribution would no longer hold true. Therefore, the channel flow-maldistribution is considered. The water formed at the active surface due to the electrochemical reaction diffuses through the porous layer and eventually enters the gas flow duct. The higher gas velocities in the duct result in faster water vapour removal which leads to a lower value of water vapour into the duct and hence a lower Nusselt number.     

Proton conducting composite membranes from polysulfone and heteropolyacid for fuel cell applications

The viability of using composite membranes of heteropolyacid (HPA)/polysulfone (PSF), HPA/sulfonated polysulfone (SPSF) for use in proton exchange membrane fuel cells (PEMFC) was investigated. PSF and its sulfonated polymer, SPSF was solution‐blended with phosphotungstic acid, a commercially available HPA. Fourier transform infrared (FTIR) spectroscopy of the HPA–40/SPSF composite exhibited band shifts showing a possibility of intermolecular hydrogen bonding interaction between the HPA additive and the sulfonated polymer. The composite membranes exhibited improved mechanical strength and low water uptake. The conductivity of the composite membrane, HPA–40/SPSF, consisting of 40 wt % HPA and 60 wt % SPSF [with a degree of Sulfonation (DS) of 40%] exhibited a conductivity 0.089 S/cm at room temperature that linearly increased upto 0.14 S/cm at 120 °C, whereas the widely used commercial membrane Nafion 117, exhibited a room temperature conductivity of 0.1 S/cm that increased to only 0.12 S/cm at 120 °C. In contrast, the composite of HPA–40/PSF exhibited a proton conductivity of 0.02 S/cm at room temperature that increased only to 0.07 S/cm at a temperature of 100 °C. The incorporation of HPA into SPSF not only rendered the membranes suitable for elevated temperature operation of PEMFC but also provides an inexpensive alternative compared to Nafion. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1538–1547, 2005     

Co−Co Dinuclear Active Sites Dispersed on Zirconium-doped Heterostructured Co9S8/Co3O4 for High-current-density and Durable Acidic Oxygen Evolution

Developing cost-effective and sustainable acidic water oxidation catalysts requires significant advances in material design and in-depth mechanism understanding for proton exchange membrane water electrolysis. Herein, we developed a single atom regulatory strategy to construct Co−Co dinuclear active sites (DASs) catalysts that atomically dispersed zirconium doped Co₉S₈/Co₃O₄ heterostructure. The X-ray absorption fine structure elucidated the incorporation of Zr greatly facilitated the generation of Co−Co DASs layer with stretching of cobalt oxygen bond and S−Co−O heterogeneous grain boundaries interfaces, engineering attractive activity of significantly reduced overpotential of 75 mV at 10 mA cm⁻², a breakthrough of 500 mA cm⁻² high current density, and water splitting stability of 500 hours in acid, making it one of the best-performing acid-stable OER non-noble metal materials. The optimized catalyst with interatomic Co−Co distance (ca. 2.80 Å) followed oxo-oxo coupling mechanism that involved obvious oxygen bridges on dinuclear Co sites (1,090 cm⁻¹), confirmed by in situ SR-FTIR, XAFS and theoretical simulations. Furthermore, a major breakthrough of 120,000 mA g⁻¹ high mass current density using the first reported noble metal-free cobalt anode catalyst of Co−Co DASs/ZCC in PEM-WE at 2.14 V was recorded.