国家关键技术管理计算机系统研究

本文根据国家关键技术管理工作的特点，本着提高决策质量，满足用户要求的原则，分析和设计国家关键技术管理计算机系统，为高层次宏观决策提供丰富的信息支持。     

线性电压扫描下1VIIS器件瞬态的简单模型

本文用准平衡模型分析讨论了线性电压扫描下MIS器件的I/V瞬态.文中除了给出一般的处理方法以外，还给出了几种不同电压扫描率下I/Y特性的计算结果，并与已往的模型作了比较.     

Mesoporous amorphous MnO<Subscript>2</Subscript> as electrode material for supercapacitor

A kind of novel mesoporous, electrochemical active material, amorphous MnO₂ has been synthesized by an improved reduction reaction and using supramolecular as template. The synthesized sample was characterized physically by thermogravimetric analysis, X-ray diffraction, transmission electron microscope (TEM), and Brunauer–Emmett–Teller (BET) surface area measurement, respectively. Electrochemical characterization was performed using cyclic voltammetry and chronopotentiometry in 2 mol/l KOH aqueous solution electrolyte. The results of BET and TEM analysis indicated that supramolecular template plays an important role in the process of big specific surface area mesoporous material forming. After sintering at 200 °C, the sample still remained an amorphous structure, and its specific capacitance reached 298.7 F/g and presented a very stable capacitance after 500 cycles. In addition, the electrochemical process, such as ion transfer and electrical condition, was also investigated with electrochemical impedance spectroscopy.     

载氧化钌碳纳米管超级电容器电极

研究了一种采用溶胶-凝胶方法制备超细氧化钌粉末的新方法，该方法制备的氧化钌电极材料在250 ℃热处理后具有570 F•g－1的比电容量并具有典型的多孔特征.通过在碳纳米管表面化学沉积氧化钌的方法制备了不同成分的氧化钌/碳纳米管复合电极,并探讨了其电化学伏安特性和直流充放电特性.该复合电极具有高能量密度特性，同时还具有良好的高功率放电特性.     

Flexible Polyester Cellulose Paper Supercapacitor with a Gel Electrolyte

A low-cost polyester cellulose paper has been used as a substrate for a flexible supercapacitor device that contains aqueous carbon nanotube ink as the electrodes and a polyvinyl alcohol (PVA)-based gel as the electrolyte. Gel electrolytes have attracted much interest due to their solvent-holding capacity and good film-forming capability. The electrodes are characterized for their conductivity and morphology. Because of its high conductivity, the conductive paper is studied in supercapacitor applications as active electrodes and as separators after coating with polyvinylidene fluoride. Carbon nanotubes deposited on porous paper are more accessible to ions in the electrolyte than those on flat substrates, which results in higher power density. A simple fabrication process is achieved and paper supercapacitors are tested for their performance in both aqueous and PVA gel electrolytes by using galvanostatic and cyclic voltammetry methods. A high specific capacitance of 270 F g⁻¹ and an energy density value of 37 W h kg⁻¹ are achieved for devices with PVA gel electrolytes. Furthermore, this device can maintain excellent specific capacitance even under high currents. This is also confirmed by another counter experiment with aqueous sulfuric acid as the electrolyte. The cycle life, one of the most critical parameters in supercapacitor operations, is found to be excellent (6000 cycles) and less than 0.5 % capacitance loss is observed. Moreover, the supercapacitor device is flexible and even after twisting does not show any cracks or evidence of breakage, and shows almost the same specific capacitance of 267 F g⁻¹and energy density of 37 W h kg⁻¹. This work suggests that a paper substrate can be a highly scalable and low-cost solution for high-performance supercapacitors.     

Carbon/carbon supercapacitors

Supercapacitors, or electrochemical capacitors, are a power storage system applied for harvesting energy and delivering pulses during short periods of time. The commercially available technology is based on charging an electrical double-layer (EDL), and using high surface area carbon electrodes in an organic electrolyte. This review first presents the state-of-the-art on EDL capacitors, with the objective to better understand their operating principles and to improve their performance. In particular, it is shown that capacitance might be enhanced for carbons having subnanometric pores where ions of the electrolyte are distorted and partly desolvated. Then, strategies for using environment friendly aqueous electrolytes are presented. In this case, the capacitance can be enhanced through pseudo-faradaic contributions involving i) surface functional groups on carbons, ii) hydrogen electrosorption, and iii) redox reactions at the electrode/electrolyte interface. The most promising system is based on the use of aqueous alkali sulfate as electrolyte allowing voltages as high as 2 V to be reached, due to the high overpotential for di-hydrogen evolution at the negative electrode.     

Electrospun Porous NiCo2O4 Nanotubes as Advanced Electrodes for Electrochemical Capacitors

Novel, porous NiCo₂O₄ nanotubes (NCO‐NTs) are prepared by a single‐spinneret electrospinning technique followed by calcination in air. The obtained NCO‐NTs display a one‐dimensional architecture with a porous structure and hollow interiors. The effect of precursor concentration on the morphologies of the products is investigated. Due to their unique structure, the prepared NCO‐NT electrode exhibits a high specific capacitance (1647 F g^?1 at 1 A g^?1), excellent rate capability (77.3 % capacity retention at 25 A g^?1), and outstanding cycling stability (6.4 % loss after 3000 cycles), which indicates it has great potential for high‐performance electrochemical capacitors. The desirable enhanced capacitive performance of NCO‐NTs can be attributed to the relatively large specific surface area of these porous and hollow one‐dimensional nanostructures.     

Influence of sputter power on structural and electrical properties of TiO2 films for Al/TiO2/Si gate capacitors

Titanium dioxide (TiO₂) thin films were deposited onto p‐Si substrates held at room temperature by reactive Direct Current (DC) magnetron sputtering at various sputter powers in the range 80–200 W. The as‐deposited TiO₂ films were annealed at a temperature of 1023 K. The post‐annealed films were characterized for crystallographic structure, chemical binding configuration, surface morphology and optical absorption. The electrical and dielectric properties of Al/TiO₂/p‐Si structure were determined from the capacitance–voltage and current–voltage characteristics. X‐ray diffraction studies confirmed that the as‐deposited films were amorphous in nature. After post‐annealing at 1023 K, the films formed at lower powers exhibited anatase phase, where as those deposited at sputter powers > 160 W showed the mixed anatase and rutile phases of TiO₂. The surface morphology of the films varied significantly with the increase of sputter power. The electrical and dielectric properties on the air‐annealed Al/TiO₂/p‐Si structures were studied. The effect of sputter power on the electrical and dielectric characteristics of the structure of Al/TiO₂/p‐Si (metal‐insulator‐semiconductor) was systematically investigated. Copyright © 2014 John Wiley & Sons, Ltd.     

Three-dimensional bundle-like multiwalled carbon nanotubes composite for supercapacitor electrode application

Bundle-type mutil-walled carbon nanotubes (MWCNTs) composite electrode is the first investigation and publication for the supercapacitor application. According to the thermogravimetric analysis results, as-synthesized BCNTs are considered as the electrode materials for supercapacitors and electrochemical double-layer capacitor in this study. The Brunauer–Emmett–Teller specific surface area of as-prepared bundled carbon nanotubes (BCNTs) is 95.29 m²/g given to a type III isotherm and H3 hysteresis loops. Slow scanning rates promote and enhance to achieve high C_b because of the superior conductivity of CNT bundles and one side close-layered Ni/Mg/Mo alloy inside the BCNT-based electrode and facile electron diffusivity between electrolyte and electrode. The specific capacitance C_s (1,560 F/g) is nearly equal to the maximum specific capacitance, which the BCNT-based composite electrode can actually be able to charge or fill in. The maximum energy density value is 195 Wh/kg with corresponding power density values of 0.21 kW/kg. Furthermore, the active 3D BCNTs material fabricated electrode enhances to contact the electrolyte directly and decreases the ion diffusion limitation. Electrochemical impedance spectroscopy spectrum summarized as the low-frequency area controls by mass transfer limitation, and the high-frequency area dominates by charge transfer of kinetic control. After 2,000 consecutive cyclic voltammetry sacnings and galvanostatic charge-discharge cycles at a current density of 1.67 A/g performs, the specific capacitance retentions of 3D BCNTs electrodes achieved 128.2 and 77.3%, respectively. Three-dimensional BCNT composite electrodes exhibit good conductivity and low charge transfer resistance, which is beneficial to fast charge transfer between the BCNTs electrode materials and electrolytes.     

Tailoring the dielectric properties and energy storage density of 1−x(0.94NaNbO3−0.06SZ)−xBi2O3 through substitution strategy

Energy storage using dielectric capacitors is a growing area of research and development. However, designing a highly performing dielectric capacitor is still a challenge. Despite the excellent results achieved in lead-based dielectrics, lead-free substitutes are essential because of the environmental concerns associated with lead-based products. The lead-free 1?x (0.94NaNbO₃? 0.06SrZrO₃)+ x Bi₂O₃ ceramics abbreviated NNSZ + xB for x = 0.0, 0.05, 0.1, 0.15, and 0.20 was fabricated via solid-state reaction. A recoverable energy density of 2.93 J cm?³ was obtained for NNSZ+0.1B, associated with high thermal stability (25–130 °C), excellent cycling (N = 10⁵), and high efficiency (η) of 83.5%. Moreover, the introduction of Bi₂O₃ significantly improved the electrical insulation (?_r at 1 kHz = 1608 and tan δ = 0.0038) and breakdown strength (380 kVcm?¹) of NNSZ+0.1B by minimizing the formation of sodium, bismuth, and oxygen vacancies. The results obtained in this study provide a benchmark for further investigations on NaNbO₃-based ceramics. More importantly, this study suggests that NNSZ + xB ceramics can be used in pulsed power technology.