Real time estimation of CO2 laser weld quality for automotive industry

Laser welding is one of the most precise welding processes in joining sheet metals. In laser welding, performing real time evaluation of the welding quality is very important to enhance the efficiency of the welding process. In this study, the plasma and spatter, which are generated during laser welding, are measured using UV and IR photodiodes. The factors that influence weld quality are classified into five categories; optimal heat input, slightly low heat input, low heat input, partial joining due to gap mismatch, and nozzle deviation. The data number deviated from reference signals and their standard deviations were also considered to evaluate the qualities. A system was also formulated to perform real time evaluations of the weld quality using a fuzzy multi-feature pattern recognition with the measured signals.     

Scattering of Laser Light from Mixed Micelles

Dynamic and static scattering of light was employed to investigate mixed micelles of two homologous anionic surfactants-sodium octyl sulfate and sodium hexadecyl sulfate, above the phase boundary temperature and critical micelle concentrations (cmc). The results indicate that the mixed micelles change from prolate to sphcrical as the molar ratio SOS/SHS increases from 1 to 8. Below 1 or above 8, the formation of micelles is due to one surfactant dissolving the other.     

Laser induced copper electroless plating on polyimide with Q-switch Nd:YAG laser

The results of laser induced deposition of copper on polyimide substrate from copper electrolyte solution are reported. Unlike most work reported in the literatures where CW Ar⁺ lasers were used, a second harmonic (532 nm wavelength) Q-switch Nd:YAG laser was used for our experiments. The deposition process was conducted by laser-catalyzing of the polyimide surface and subsequent photothermal-accelerated reduction of copper-complex ions in an alkaline reducing environment. The characteristics of the deposited copper line were investigated in terms of laser beam scanning speed, and the number of scans. The surface morphology and chemical composition of the deposited copper were analyzed using field emission scanning electron microscope (FESEM) and energy dispersive spectrometer (EDX). The optimum processing conditions have been identified. The copper deposit was found to adhere well to the substrate.     

一种高信噪比的双光束激光光声光谱仪原理及应用

作为一种新兴的检测手段 ,激光光声光谱技术与其他检测技术相比具有很多优点。本文设计的光声光谱仪用激光做光源 ,有两个光声池 ,分别用来放置参考样品和待测样品 ,输出结果为二者光声信号的比值。利用这一比值 ,可以由参考样品的性能参数方便地求出待测样品的相关性能参数。该光声光谱仪有效地减小了本底吸收噪声的影响 ,提高了信噪比 ,扩大了固体光声理论的应用范围。本文还阐述了该光声光谱仪在定性定量分析中的一些应用     

Reciprocating sliding wear behavior of laser-clad small amplitude Mo2Ni3Si/NiSi metal silicide composite coatings

Mo₂Ni₃Si/NiSi metal silicide composite coatings with a fine microstructure consisting of Mo₂Ni₃Si primary dendrites and the interdendritic Mo₂Ni₃Si/NiSi eutectics were fabricated on austenitic stainless steel AISI 321 by laser cladding process. Small amplitude reciprocating sliding wear resistance of the coatings is evaluated as functions of normal load and slip amplitude and the wear mechanisms were discussed based on worn surface morphology observations. Results showed that the Mo₂Ni₃Si/NiSi coatings have excellent small amplitude reciprocating sliding wear resistance.     

Radiative lifetimes in Ce I and Ce II

New radiative lifetime measurements based on time-resolved laser-induced fluorescence techniques are reported for 18 even-parity levels belonging to the 4f5d^26p and 4f ²5d ² configurations of Ce I and 6 even-parity levels belonging to the 5d^26s, 4f5d6p, and 4f6s6p configurations of Ce II. Free neutral and singly ionized cerium atoms were produced by laser ablation. The Ce I and Ce II levels range in energy from 26 545 to 29 102 cm^-1, and 42 573 to 48 152 cm^-1, respectively. Received 25 September 2002 Published online 4 March 2003     

Hybrid numerical—experimental approach for investigation of dynamics of microcantilever relay system

The time average holography measurements of the vibrating microelectromechanical switch (MEMS) were performed in this study. Experimental measurement results exhibit good agreement with computer generated holographic interferogram analysis. The validation of experimental investigations versus numerical analysis provides the necessary background to analyze the dynamical characteristics of micromechanical systems in virtual numerical environments. Direct application of fringe counting techniques for reconstruction of motion from time average holograms cannot be straightforward if the analyzed micromechanical systems contain motion limiters. Modifications of a classical time average holographic technique enable qualitative analysis of MEMS and can be applied for investigation of dynamical properties of much broader classes of MEMS systems.     

Spectral features of laser induced plasma from YBa2Cu3O7 and GdBa2Cu3O7 highT c superconductors

Laser induced plasma emission spectra from highT _c superconducting samples of YBa₂Cu₃O₇ and GdBa₂Cu₃O₇ obtained with 1.06μm radiation from a Q switched Nd:YAG laser beam has been analysed. The results clearly show the presence of diatomic oxides in addition to ionized species of the constituent metals in the plasma thus produced.     

Effects of aldehyde or dipyrromethane substituents on the reaction course leading to meso-substituted porphyrins

To better understand the effects of diverse substituents on reactions leading to porphyrins, pyrrole+aldehyde condensations and related reactions of dipyrromethanes were examined. The course of pyrrole+aldehyde condensations was investigated by monitoring the yield of porphyrin (by UV-Vis spectroscopy), reaction of aldehyde (by TLC), and changes in the composition of oligomers (by laser desorption mass spectrometry). Reaction reversibility was examined via exchange experiments. Reversibility of reactions leading to porphyrin was further probed with studies of dipyrromethanes. The reaction course was found to depend on the nature of the substituent and the acid catalyst. Alkyl or electron-donating substituents displayed levels of reversibility (exchange/scrambling) on par or greater than that of the phenyl substituent, whereas electron-withdrawing or sterically bulky substituents exhibited little to no reversibility. The results obtained provide insight into the electronic and steric effects of different substituents and should facilitate the design of synthetic plans for preparing porphyrinic macrocycles.     

用于激光推进的高功率激光器的选择

 从激光推进的要求出发，阐述了用于激光推进的高功率激光器的选择原则，即激光器必须满足：（1）高的平均功率和峰值功率；（2）高的单脉冲能量；（3）高的重复频率；（4）优良的大气传输特性。主要分析了目前YAG固体激光器、自由电子激光器和TEA脉冲CO₂激光器的特点，通过上述4个方面性能的比较，认为在目前水平下，TEA脉冲CO₂激光器是进行激光推进的首选强激光源，其优点表现在：功率可达10kW量级，单脉冲能量可达0.5~1kJ，重复频率为20~40Hz；激光波长处于大气传输窗口，对大气变化不敏感；工作物质快速流动，不存在热透镜效应和破坏阈值；相关光学元件易于制造；光束质量较好；运行成本低。