轴流风扇叶片端导叶作用的研究

本文采用数值方法研究了叶片端导叶对轴流风扇性能的影响。通过与普通开式轴流风扇比较,分析了叶片端导叶对内部流动作用的机理.数值计算结果表明:叶片端导叶的安装位置将影响轴流风扇气动效率,安装叶片端导叶不能提高风扇静压升,但是在压力面安装时能有效地减小风扇叶顶泄漏流与主流的掺混损失;在设计流量下,压力面安装叶片端导叶使泄漏涡的作用范围较小,涡核更靠近吸力面;吸力面安装叶片端导叶弱化了泄漏涡的强度但没有减小泄漏涡的作用范围。     

前缘弯掠斜流转子叶顶间隙流动特性数值分析

本文对前缘弯掠斜流转子叶顶间隙内的流动特性进行了数值分析。结果表明:叶顶间隙气流与主流发生卷吸而生成泄漏涡。泄漏涡作用的区域具有较低的压力分布。在叶片通道内,泄漏涡沿着与转子旋向相反的方向朝相邻叶片的压力面移动。大间隙时的泄漏涡比小间隙时强烈。低流量时泄漏涡的作用区域比高流量时大。在各种流量特性下,叶顶尾缘近吸力面区域都存在着二次间隙流。     

A compact shock-assisted free-piston driver for impulse facilities

A free-piston driver that employs entropy-raising shock processes with diaphragm rupture has been constructed, which promises significant theoretical advantages over isentropic compression. Results from a range of conditions with helium and argon driver gases are reported. Significant performance gains were achieved in some test cases. Heat losses are shown to have a strong effect on driver processes. Measurements compare well with predictions from a quasi-one-dimensional numerical code. Received 7 September 1996 / Accepted 5 October 1996     

Hyers–Ulam–Rassias stability of Cauchy equation in the space of Schwartz distributions

We reformulate and prove the Hyers–Ulam–Rassias stability of Cauchy equation in the space of Schwartz tempered distributions and Fourier hyperfunctions.     

Chip-calorimeter for small samples

A method for measuring heat capacities of small samples using a chip-calorimeter and a heat pulse technique is described. The theoretical background to calculate the heat transport properties and the heat capacity of the sample from the pulse response function is given. Problems and potentials of the method are discussed. An example is given.     

关于半线性热方程的死角性质

本文考虑下述问题：这里，．本文证明了在发生死角时只有有限个死角点．     

回旋管输出窗热性质的研究

一、引 言 输出窗是回旋管的能量输出端口,它的特性直接影响到回旋管的性能和寿命。输出窗的设计包括电特性和热特性的研究。当输出功率增加时,热特性的研究变得非常重要以便寻求合理有效的冷却措施。 输出窗由波导和介质片(块)两部分组成。回旋管的输出波导是圆波导,介质一般做成     

Pointwise and L2 bounds in some nonstandard problems for the heat equation

We consider some initial-boundary value problems for the linear and nonlinear heat equation where the gradient of the solution is prescribed on the boundary. Assuming that a solution exists, we obtain bounds for the solution and its gradient by maximum principle arguments or by means of differential and integral inequalities.     

Heat of adsorption and density distribution in slit pores with defective walls: GCMC simulation studies and comparison with experimental data

The adsorption behavior (capacity, density distribution and packing density) and the isosteric heat versus loading in a slit pore whose walls contain defective graphene layers are investigated in this paper. The defective wall is characterized by the extent and size of the defect. Simulation results obtained with the Grand Canonical Monte Carlo method reveal complex patterns of isosteric heat, and this complex behavior is a result of the interplay between three factors: (i) the surface heterogeneity (solid-fluid interaction, sites with varying degree of affinity), (ii) fluid-fluid interaction and (iii) the overlapping of potentials exerted by the two defective walls. We illustrate this with argon adsorption in pores of various sizes, and results obtained from the simulation agree qualitatively with the experimental data at 77 K on Saran microporous S600H and micro-mesoporous S84 charcoals of Beebe et al. [R.A. Beebe, B. Millard, J. Cynarski, J. Am. Chem. Soc. 75 (1953) 839]. The S600H was found to contain pores predominantly in the neighborhood of 7 Å with 30% of defect and a defective size of 2.84 Å. This is consistent with the argument made by Beebe et al. that this sample is a microporous solid and most pores can accommodate only one layer. The other sample, S84, has larger pores than S600H, and it is found that it has a wider pore size distribution and the pore width is centered at about 12 Å.     

Integrability of det▽u and Evolutionary Wente''s Problem Associated to Heat Operator

In this note, the authors resolve an evolutionary Wente's problem associated to heat equation, where the special integrability of det▽u for u ∈ H1(R2,R2) is used.