Molecular structure,vibrational spectroscopic and chemical reactivity of nematogenic p-n-alkylbenzoic acids: A comparative computational analysis

Molecular structure and vibrational spectroscopic studies of higher homologous series nematogenic p-n-alkylbenzoic acids (nBAC) that have 6 (6BAC) and 7 (7BAC) carbon atoms in the alkyl chain have been investigated using the Density Functional Becke3-Lee-Yang-Parr (B3LYP) level with the basis set 6-31++G (d.p) and Hartree Fock (HF) with the same basis set. The observed vibrational spectra has been resolved and assigned in detail for comparision with both the molecules. These results indicate that DFT and HF values are slightly different at both the levels. A comparision of chemical reactivity such as HOMO (E_H), LUMO (E_L) energies, energy gap (E_g), ionization energy (I), electron affinity (A), electro negativity (χ), chemical hardness (η), electronic chemical potential (μ), electrophilicity index (ω), and softness (S) has been made. It has been observed that the decrement has occurred in the energy band gap value of isolated molecule with increment in alkyl chain length. This provides valuable information regarding enhancing the stability of liquid crystal materials by maintaining the conductivity.     

Imprint lithography of pyramidal photonic pillars using hydrazine etching

An inexpensive method to produce a pyramidal-type 2D photonic structures in the silicon substrate was proposed. The method is based on the combination of imprint lithography and wet Si1 0 0 etching in water solution of hydrazine, which etches 1 1 1 faces much more slowly than others. Thermally grown SiO₂ mask for the hydrazine etching was used, because single Al mask cannot be well bonded to the substrate and tends to peel during the etching. It was revealed that transmittance in the infrared spectrum region of the patterned silicon decreases by about five times compared with that of flat silicon substrate and this decrease is almost independent of the angle of the incident beam. In the infrared region, decrease of transmittance of the patterned samples is directly proportional to the wave number. The shape of formed pyramids has strong influence on the transmittance. Decrease of the transmittance is much more rapid and larger in the case of sharpless pillars.     

电致发光色纯性增强的硅基有机微腔

报道了硅基有机微腔的电致发光（EL）.该微腔由上半透明金属膜、中心有源多层膜和多孔硅分布Bragg反射镜（PS DBR）组成.半透明金属膜由Ag（２０nm）构成，充当发光器件的负电极和微腔的上反射镜.有源多层膜由Al (1 nm) / LiF(05 nm) /Alq3/Alq3:DCJTB/NPB/CuPc/ITO/SiO2组成，其中的Al/LiF为电子注入层，ITO为正电极，SiO2为使正、负电极电隔离的介质层.该PS DBR是采用设备简单、成本低廉且非常省时的电化学腐蚀法用单晶Si来制备的；该PS 关键词： 电化学腐蚀 电致发光 窄峰发射 硅基有机微腔     

采用MSDI严格角动量投影46Ti、48Cr形变HF谱

采用修正的表面δ相互作用(MSDI),以球形壳模型单粒子态作基矢,对fp壳层区偶偶核⁴⁶Ti、⁴⁸Cr进行形变Hartree–Fock(HF)计算,并用形变HF单粒子态构造Slater行列式波函数,即形变HF内禀态,然后对其实施严格角动量投影程序,得到比较合理的结果.     

High-density plasma etching of indium-zinc oxide films in Ar/Cl2 and Ar/CH4/H2 chemistries

The dry etching characteristics of transparent and conductive indium-zinc oxide (IZO) films have been investigated using an inductively coupled high-density plasma. While the Cl₂-based plasma mixture showed little enhancement over physical sputtering in a pure argon atmosphere, the CH₄/H₂/Ar chemistry produced an increase of the IZO etch rate. On the other hand, the surface morphology of IZO films after etching in Ar and Ar/Cl₂ discharges is smooth, whereas that after etching in CH₄/H₂/Ar presents particle-like features resulting from the preferential desorption of In- and O-containing products. Etching in CH₄/H₂/Ar also produces formation of a Zn-rich surface layer, whose thickness (∼40 nm) is well-above the expected range of incident ions in the material (∼1 nm). Such alteration of the IZO layer after etching in CH₄/H₂/Ar plasmas is expected to have a significant impact on the transparent electrode properties in optoelectronic device fabrication.     

Microstructure effect on microtopography of chemically etched α + β Ti alloys

Microstructure effect on chemical etching behavior of the annealed Ti-6Al-4V and Ti-3Al-2.5V titanium (Ti) alloys was compared with that of unalloyed commercially pure titanium. The microstructural evolution of structure phases after annealing the titanium and its alloys at temperature near and above β transus and followed by furnace cooling to room temperature was studied using optical microscope, scanning electron microscope and X-ray diffraction techniques. The microstructure study illustrates that the heat treatment enhanced partitioning effect allows extensive formation of hemispherical and near spherical pits roughened surface to be readily acquired by chemically etching the annealed α + β titanium alloys. The kinetics of the chemical etching reaction process show a linear dependence on time. The annealed α + β titanium alloys that exhibit relatively lower weight loss and thickness reduction rate illustrate less chemical activity than the annealed unalloyed titanium.     

Microstructure array on Si and SiOx generated by micro-contact printing, wet chemical etching and reactive ion etching

A method, combining micro-contact printing (μCP), wet chemical etching and reactive ion etching (RIE), is reported to fabricate microstructures on Si and SiOx. Positive and negative structures were generated based on different stamps used for μCP. The reproducibility of the obtained microstructures shows the methodology reported herein could be useful in Micro-Electro-Mechanical Systems (MEMS), optical and biological sensing applications.     

四阶累积量的MUSIC算法在海流测向中的应用

针对高频地波雷达系统OSMAR2000海流测向中海流元数不易估计的问题，利用四阶谱累积量MUSIC算法的空间谱结构特点，采用试探法确定信号源数并估计信号源的位置．通过对模拟海流和实测数据的处理实验表明，利用该算法可以较准确地估计出海流元的个数和方位，并且比传统MUSIC方法获得更小的角度估计方差，有效地反演了海洋表面流信息．     

A DC excited waveguide multibeam CO2 laser using high frequency pre-ionization technique

High power industrial multibeam CO₂ lasers consist of a large number of closely packed parallel glass discharge tubes sharing a common plane parallel resonator. Every discharge tube forms an independent resonator. When discharge tubes of smaller diameter are used and the Fresnel numberN ≪ 1 for all resonators, they operate in waveguide mode. Waveguide modes have excellent discrimination of higher order modes. A DC excited waveguide multibeam CO₂ laser is reported having six glass discharge tubes. Simultaneous excitation of DC discharge in all sections is achieved by producing pre-ionization using an auxiliary high frequency pulsed discharge along with its other advantages. Maximum 170 W output power is obtained with all beams operating in EH₁₁ waveguide mode. The specific power of 28 W/m is much higher as compared to similar AC excited waveguide multibeam CO₂ lasers. Theoretical analysis shows that all resonators of this laser will support only EH₁₁ mode. This laser is successfully used for woodcutting     

Angular response characteristic of pyramid shape fast neutron dosimeter using CR-39 films

CR-39 is a highly sensitive etched track detector for neutron monitoring and dosimetry applications but its dose equivalent response is strongly direction dependent with respect to the incident neutrons. This is considered to be a major drawback for their use. In the present study, an attempt has been made to develop a pyramid shaped dosimeter, which consists of polyethylene material of thickness 1 mm with the provision to hold three CR-39 films at an angle of 35° to each other. The response of CR-39 in this configuration under optimum electrochemical etching at elevated temperature have been found nearly angular independent and therefore the dosimeter can be used for neutron monitoring, i.e. personnel as well as area monitoring.