Influence of fluoride on f-f transitions of Eu in LiEuM2O8 (M=Mo, W)

The influence of fluoride on the luminescence of LiEuM₂O₈ (M=Mo, W) was studied. LiEuMo₂O₈ and LiEuW₂O₈ formed the whole range of solid solutions, which emitted intense red luminescence under the excitations by 395, 465 and 535 nm wavelengths. When doped with fluoride, the materials also formed solid solutions and the luminescent intensity was remarkably enhanced. The phosphor with optimized compositions in this system would be a promising red component for solid-state lighting devices based on GaN light-emitting diodes.     

X-ray damage characterization in BaLiF3,KMgF3 and LiCaAlF6 complex fluorides

Two-inch sized KMgF₃,BaLiF₃ and LiCaAlF₆ (LiCAF) single crystals were grown by the Czochralski method under a CF₄ atmosphere. X-ray irradiation was used to carry out a comparative study of induced optical absorption phenomena and colour centre creation in the ultra-violet and visible spectral regions. The integral of the induced absorption spectra is significantly lower in LiCAF with respect to the other studied materials. It is found that the amplitude of the F-absorption band is suppressed more than a factor of 3 by Mg-doping. For Mg-doped crystals, the optimum doping concentration is about 0.2 mol% of Mg²⁺.     

Facile synthesis of 9-（N-amino-4-fluoromethyl-3-pyrrolidinyl）-2- fluoro-6-aminopurine from trans-4-hydroxy-L-proline

A novel and simple procedure for synthesis of azanucleoside by Mitsunobu reaction between N-(p-nitrobenzyloxycarbonyl)- trans-4-hydroxy-D-proline methyl ester obtained from trans-4-hydroxy-L-proline after six-step reaction and 2-fluoro-6-azidopurine is described,and azanucleoside is fluorinated by new fluridizer 2,2-difluoro-1,3-dimethylimidazolidine (DFI).All reactions could be carded out under mild condition.     

Ammonium hexafluorosilicate salts

The preparation and characterization of the ammonium hexafluorosilicate salts, 2[R]⁺ [SiF₆]²⁻ (where R=piperidinium (2), methylammonium (3), quinolinium (4), acridinium (5), 2,2,6,6-tetramethylpiperidinium (6), and propylammonium (7)) is described.The salts were prepared from the reaction of the corresponding alkylammonium fluoride with silica gel. The compounds were characterized by NMR, IR, mass spectrometry and in the case of 1 (piperidinium fluoride), 2-4 by X-ray crystallography. Compounds 1-3 crystallize in the orthorhombic crystal system (space groups Iba2, Fdd2, and Pnnm, respectively), with Z=8, 14, and 4, respectively. Compound 4 crystallizes in the triclinic space group P-1, with Z=2. Compounds 1-4 exhibit hydrogen bonding.     

集成微管路离子选择电极功能块研究

本文对微型管状离子选择电极在流动条件下的电化学特征进行了研究,并设计了新的集成微管路离子选择以电极功能块。用此微型装置测定了土壤、血清、水和药物中的K~+、Na~+、pH、Cl~-、F~-、阿托品、东茛菪碱,并和各种标准方法作了比较,获得满意分析结果。     

Development of aryl-containing dipyrrolyldiketone difluoroboron complexes (BONEPYs): Tune the hydrogen bond o–CH···F for fluoride recognition

Dipyrrolyldiketone difluoroboron complexes (BONEPYs) were synthesized by condensation of the corresponding pyrroles and malonyl chloride followed by treatment with BF₃·OEt₂. The aryl-substituted pyrrole is introduced to form a cyclic system in order to investigate anion binding studies. In BONEPYs 1–3 the o-H of the aryl group forms hydrogen bonding with F⁻ to give a more table complex. In contrast, the intramolecular hydrogen-bonded BONEPY endo-4 is more stable than its exo isomer. While adding F⁻, the hydrogen bonds must be broken first to give 4·(3)F⁻. Owing to the electron-rich group (-OMe), the o-H of the phenyl group can hardly interact with F⁻ via hydrogen bonding to give the less stable complex 4·(5)F⁻. The energy differences between the different conformations were calculated using DFT methods, which is consistent to the experimental observations.     

偏氟乙烯和四氟乙烯共聚反应中链自由基的反应性

应用高分辨率核磁共振仪研究了一系列不同组成的偏氟乙烯和四氟乙烯共聚物。指出,共振核—CF_2—的化学位移不仅受第一、二邻位基团的影响,也受第三邻位的影响。偏氟乙烯和四氟乙烯以无规共聚进行反应,在共聚反应中的链自由基﹏CF_2·或﹏CH_2·容易增长于CH_2=CF_2的CH_2端,而链自由基﹏CH_2·在偏氟乙烯和四氟乙烯共聚反应中的增长倾向于四氟乙烯。     

Determination of total fluoride in HF/HNO3/H2SiF6 etch solutions by new potentiometric titration methods

In the photovoltaic industry the etching of silicon in HF/HNO₃ solutions is a decisive process for cleaning wafer surfaces or to produce certain surface morphologies like polishing or texturization. With regard to cost efficiency, a maximal utilisation of etch baths in combination with highest quality and accuracy is strived. To provide an etch bath control realised by a replenishment with concentrated acids the main constituents of these HF/HNO₃ etch solutions including the reaction product H₂SiF₆ have to be analysed. Two new methods for the determination of the total fluoride content in an acidic etch solution based on the precipitation titration with La(NO₃)₃ are presented within this paper. The first method bases on the proper choice of the reaction conditions, since free fluoride ions have to be liberated from HF and H₂SiF₆ at the same time to be detected by a fluoride ion-selective electrode (F-ISE). Therefore, the sample is adjusted to a pH of 8 for total cleavage of the SiF₆²⁻ anion and titrated in absence of buffers. In a second method, the titration with La(NO₃)₃ is followed by a change of the pH-value using a HF resistant glass-electrode. Both methods provide consistent values, whereas the analysis is fast and accurate, and thus, applicable for industrial process control.     

Preparation of Fluorine‐Doped Lead Dioxide Modified Electrodes for Electroanalytical Applications

The effect of F^? on the modified films of lead dioxide in morphology and structure was studied. The results obtained by cyclic voltammetry (CV), X‐diffractometer (XRD) and scanning electron microscope (SEM) techniques indicated that F^? could change the magnitude of lead dioxide crystal grain and the preferred crystallizing orientation on the substrate surface, even though it didn't change the basic structure of PbO₂. When the modified electrode was applied as an analytical sensor to determine phenolic compounds, the linearity was in the range of 2×10^?5 – 1×10^?3 mol/L and the detection limit was 2.5×10^?6 mol/L. It was all found that the stability and reproducibility of the oxide‐modified electrodes were improved by additional F^?.