主动冷却点阵夹层防热结构温度响应计算模型北大核心CSCD

针对点阵夹层结构主动热防护问题,建立了夹层结构面板和芯体导热与冷却剂对流耦合的非稳态传热理论模型,利用有限体积法离散控制方程并在MATLAB中进行了迭代求解.模型首次考虑了面板与夹芯杆之间的收缩热阻,并利用分离变量法得到了收缩热阻的近似解析解.基于单胞模型和周期性边界条件,模拟得到了模型所需的表面对流传热系数h_(b)和h_(fin).最后,选取多单胞计算工况进行数值模拟和理论模型对比,并讨论了收缩热阻对模型预测精度的影响.结果表明:理论模型能够准确预测夹层结构及内部流体的温度变化,理论与仿真之间的最大误差不超过1%;随着外加热流密度不断增大,忽略收缩热阻使得计算结果造成的误差不断增大;与数值模拟相比,理论模型可显著地减少计算时间并节省计算资源,尤其适用于非均匀、非稳态复杂热载荷下点阵夹层结构的温度响应计算.     

The thermoelastic Aldo contact model with frictional heating

In the study of the essential features of thermoelastic contact, Comninou and Dundurs (J. Therm. Stresses 3 (1980) 427) devised a simplified model, the so-called “Aldo model”, where the full 3D body is replaced by a large number of thin rods normal to the interface and insulated between each other, and the system was further reduced to 2 rods by Barber's Conjecture (ASME J. Appl. Mech. 48 (1981) 555). They studied in particular the case of heat flux at the interface driven by temperature differences of the bodies, and opposed by a contact resistance, finding possible multiple and history dependent solutions, depending on the imposed temperature differences.The Aldo model is here extended to include the presence of frictional heating. It is found that the number of solutions of the problem is still always odd, and Barber's graphical construction and the stability analysis of the previous case with no frictional heating can be extended. For any given imposed temperature difference, a critical speed is found for which the uniform pressure solution becomes non-unique and/or unstable. For one direction of the temperature difference, the uniform pressure solution is non-unique before it becomes unstable. When multiple solutions occur, outermost solutions (those involving only one rod in contact) are always stable.A full numerical analysis has been performed to explore the transient behaviour of the system, in the case of two rods of different size. In the general case of N rods, Barber's conjecture is shown to hold since there can only be two stable states for all the rods, and the reduction to two rods is always possible, a posteriori.     

On MRI turbulence quantification

Turbulent flow, characterized by velocity fluctuations, accompanies many forms of cardiovascular disease and may contribute to their progression and hemodynamic consequences. Several studies have investigated the effects of turbulence on the magnetic resonance imaging (MRI) signal. Quantitative MRI turbulence measurements have recently been shown to have great potential for application both in human cardiovascular flow and in engineering flow. In this article, potential pitfalls and sources of error in MRI turbulence measurements are theoretically and numerically investigated. Data acquisition strategies suitable for turbulence quantification are outlined. The results show that the sensitivity of MRI turbulence measurements to intravoxel mean velocity variations is negligible, but that noise may degrade the estimates if the turbulence encoding parameter is set improperly. Different approaches for utilizing a given amount of scan time were shown to influence the dynamic range and the uncertainty in the turbulence estimates due to noise. The findings reported in this work may be valuable for both in vitro and in vivo studies employing MRI methods for turbulence quantification.     

旅行推销员问题的凸包收缩法

本提出一种用凸包收缩来解决旅行推销员问题。首先形成一个凸包初始环路。然后，逐个考察凸包内的点，按照增加值从小到大的顺序依次插入，直至考察完所有的点。从而得到一个包含所有点的环路，即旅行推销员问题的一个满意解。     

Flexible particle flow‐focusing in microchannel driven by droplet‐directed induced‐charge electroosmosis

We report herein a novel microfluidic particle concentrator that utilizes constriction microchannels to enhance the flow‐focusing performance of induced‐charge electroosmosis (ICEO), where viscous hemi‐spherical oil droplets are embedded within the mainchannel to form deformable converging‐diverging constriction structures. The constriction region between symmetric oil droplets partially coated on the electrode strips can improve the focusing performance by inducing a granular wake flow area at the diverging channel, which makes almost all of the scattered sample particles trapped within a narrow stream on the floating electrode. Another asymmetric droplet pair arranged near the outlets can further direct the trajectory of focused particle stream to one specified outlet port depending on the symmetry breaking in the shape of opposing phase interfaces. By fully exploiting rectification properties of induced‐charge electrokinetic phenomena at immiscible water/oil interfaces of tunable geometry, the expected function of continuous and switchable flow‐focusing is demonstrated by preconcentrating both inorganic silica particles and biological yeast cells. Physical mechanisms responsible for particle focusing and locus deflection in the droplet‐assisted concentrentor are analyzed in detail, and simulation results are in good accordance with experimental observations. Our work provides new routes to construct flexible electrokinetic framework for preprocessing on‐chip biological samples before performing subsequent analysis.     

Integrating particle swarm optimization with genetic algorithms for solving nonlinear optimization problems

Heuristic optimization provides a robust and efficient approach for solving complex real-world problems. The aim of this paper is to introduce a hybrid approach combining two heuristic optimization techniques, particle swarm optimization (PSO) and genetic algorithms (GA). Our approach integrates the merits of both GA and PSO and it has two characteristic features. Firstly, the algorithm is initialized by a set of random particles which travel through the search space. During this travel an evolution of these particles is performed by integrating PSO and GA. Secondly, to restrict velocity of the particles and control it, we introduce a modified constriction factor. Finally, the results of various experimental studies using a suite of multimodal test functions taken from the literature have demonstrated the superiority of the proposed approach to finding the global optimal solution.     

Blockage of constrictions by particles in fluid–solid transport

Blockage is an important phenomenon in particulate flow. Work was undertaken to provide a better understanding of key hydrodynamic multiphase flow factors which cause, or contribute to, stalling and blockage in particulate feeding systems such as those used for feeding biomass into reactors. Rubber and plastic particles were hydraulically conveyed along a horizontal rectangular duct leading to constrictions of different geometries. Experimental results showed that large size, irregular shape, high volumetric concentrations of particles, small constriction dimensions and particle compressibility all increased the likelihood of blockage. Reynolds number also had a significant effect on particle behaviour and blockage propensity. The pressure drop needed to break a blockage is also considered, based on a simple horizontal packed bed model.     

An experimental investigation of pulsatile flow through a smooth constriction

Measurements of flow disturbances in the downstream region of modeled stenoses in a rigid tube, with upstream pulsatile flow are reported. Experiments were conducted over physiologically relevant mean Reynolds numbers of 600; based on the tube diameter and the time-averaged value of upstream centerline velocity. Contoured constrictions with 25%, 50% and 75% area reductions were investigated and velocity data were obtained from ensemble averaging techniques (phase-locked waveform). Experimental data over extensive spatial regions of poststenotic fields were taken, employing a two-component laser Doppler velocimeter LDV. Constant time sampling techniques for performing data or frequency analyses were used to avoid velocity bias and to study the evolution of poststenotic flow disturbances. It is found that different types of flow disturbances exist downstream of the constriction. Data analysis methods with the aid of flow visualization allow accurate classification of the disturbances which are sensitive indicators of mild to moderate constrictions. Although the present study was motivated by a biological situation, sufficient data were reported in detail that they may also be used by investigators working in computational fluid dynamics.     

Effect of couple stresses on the flow in a constricted annulus

The flow of an incompressible couple stress fluid in an annulus with local constriction at the outer wall is considered. This configuration is intended as a simple model for studying blood flow in a stenosed artery when a catheter is inserted into it. The effects couple stress fluid parameters α and σ, height of the constriction (ε), and ratio of radii (k) on the impedance and wall shear stresses are studied graphically. Graphical results show that the resistance to the flow as well as the wall shear stress increases as the ratio of the radii increases and decreases as the couple stress fluid parameters increases.