Sonochemical conversion of CO2 into hydrocarbons: The Sabatier reaction at ambient conditions

In this study, we investigated an alternative method for the chemical CO₂ reduction reaction in which power ultrasound (488 kHz ultrasonic plate transducer) was applied to CO₂-saturated (up to 3%) pure water, NaCl and synthetic seawater solutions. Under ultrasonic conditions, the converted CO₂ products were found to be mainly CH₄, C₂H₄ and C₂H₆ including large amount of CO which was subsequently converted into CH₄. We have found that introducing molecular H₂ plays a crucial role in the CO₂ conversion process and that increasing hydrogen concentration increased the yields of hydrocarbons. However, it was observed that at higher hydrogen concentrations, the overall conversion decreased since hydrogen, a diatomic gas, is known to decrease cavitational activity in liquids. It was also found that 1.0 M NaCl solutions saturated with 2% CO₂ + 98% H₂ led to maximum hydrocarbon yields (close to 5%) and increasing the salt concentrations further decreased the yield of hydrocarbons due to the combined physical and chemical effects of ultrasound. It was shown that CO₂ present in a synthetic industrial flue gas (86.74% N₂, 13% CO₂, 0.2% O₂ and 600 ppm of CO) could be converted into hydrocarbons through this method by diluting the flue gas with hydrogen. Moreover, it was observed that in addition to pure water, synthetic seawater can also be used as an ultrasonicating media for the sonochemical process where the presence of NaCl improves the yields of hydrocarbons by ca. 40%. We have also shown that by using low frequency high-power ultrasound in the absence of catalysts, it is possible to carry out the conversion process at ambient conditions i.e., at room temperature and pressure. We are postulating that each cavitation bubble formed during ultrasonication act as a “micro-reactor” where the so-called Sabatier reaction -$C{O}_2+4H_2\stackrel{\mathit{Ultrasonication}}{\to }C{H}_4+2H_{2}O$ - takes place upon collapse of the bubble. We are naming this novel approach as the “Islam-Pollet-Hihn process”.     

Sandwich-like Catalyst–Carbon–Catalyst Trilayer Structure as a Compact 2D Host for Highly Stable Lithium–Sulfur Batteries

Herein, we propose the construction of a sandwich-structured host filled with continuous 2D catalysis–conduction interfaces. This MoN-C-MoN trilayer architecture causes the strong conformal adsorption of S/Li₂S_x and its high-efficiency conversion on the two-sided nitride polar surfaces, which are supplied with high-flux electron transfer from the buried carbon interlayer. The 3D self-assembly of these 2D sandwich structures further reinforces the interconnection of conductive and catalytic networks. The maximized exposure of adsorptive/catalytic planes endows the MoN-C@S electrode with excellent cycling stability and high rate performance even under high S loading and low host surface area. The high conductivity of this trilayer texture does not compromise the capacity retention after the S content is increased. Such a job-synergistic mode between catalytic and conductive functions guarantees the homogeneous deposition of S/Li₂S_x, and avoids thick and devitalized accumulation (electrode passivation) even after high-rate and long-term cycling.     

Hexagonal boron nitride quantum dots: Properties,preparation and applications

As a new type of quantum dots (QDs), hexagonal boron nitride quantum dots (BNQDs) exhibit promising potential in the applications of disease diagnosis, fluorescence imaging, biosensing, metal ion detection, and so on, because of their remarkable chemical stability, excellent biocompatibility, low cytotoxicity, and outstanding photoluminescence properties. However, the large-scale fabrication of homogeneous BNQDs still remains challenging. In this article, the properties and common fabrication methods of BNQDs are summarized based on the recent research progress. Then, the corresponding yields, morphologies, and fabrication mechanisms of these as-obtained BNQDs are discussed in detail. Moreover, the applications of these as-obtained BNQDs in different fields are also discussed. This article is expected to inspire new methods and improvements to achieve large-scale fabrication of homogeneous BNQDs, which will enable their practical applications in future.     

First principles investigations of Fe,Co, Ni in model honeycomb carbon networks

The behaviors of ferromagnetic transition metals of the first period: Fe, Co and Ni are examined within density functional theory calculations in two dimensional carbon extended networks using model structure LiC₆. Around geometry optimized structures, the energy-volume equations of states considering non magnetic and spin polarized configurations established ferromagnetic ground states with magnetizations –reduced with respect to the metals’– of 2 μ_B for FeC₆ and 1 μ_B for CoC₆ while no magnetic solution could be identified for NiC₆. In the D_6h point group of the P6/mmm space group l_m decomposition of the d states results with increasing energy into doublet state E_1g with d(x²-y²) and d(xy); singlet state A_1g d(z²) and doublet state E_2g d(xz) and d(yz) lying on E_F and responsible of the onset of magnetic moments. This was mirrored via molecular orbital approach with a construct of Fe embedded between two extended carbon networks thus validating the model structure proposed for TC₆ compounds. The 100% polarization in one spin channel allows proposing potential uses in spintronics applications.     

Luminescence investigations of the GaP-based dilute nitride Ga(NAsP) material system

Multi-quantum well heterostructures (MQWHs) of the novel Ga(NAsP)/GaP material system have been grown, pseudomorphically strained to GaP-substrate. The crystalline perfection is verified by transmission electron microscopy (TEM). For As-concentrations in excess of about 70%, a direct band structure and adequate luminescence efficiency for laser device application is observed. Temperature-dependent photoluminescence (PL) investigations show the influence of carrier localisation and non-radiative recombination processes typical for dilute nitride materials. With rising N content in the active material, the emission wavelength shifts towards longer wavelength, leading to Ga(NAs)/GaP MQW structures with photon energies below the indirect band gap of silicon (Si). At the same time the luminescence intensity drops due to an increase in non-radiative carrier traps and/or structural degradation.     

Towards molecular-scale electronics and biomolecular self-assembly

This paper provides an overview of recent research developments in the field of nanoelectronics with organic materials such as carbon nanotubes and DNA-templated nanowires. Carbon nanotubes and gold electrodes are chemically functionalized in order to contact carbon nanotubes by self-assembly. The transport properties of these nanotubes are dominated by charging effects and display clear Coulomb blockade behaviour. A different approach towards nanoscale electronics is based on the molecular recognition properties of biomolecules such as DNA. As an example, DNA is stretched between electrodes using a molecular combing technique. A two-step metallization procedure leads to the formation of highly conductive gold nanowires.     

Local adsorption sites and bondlength changes in Ni(1 0 0)/H/CO and Ni(1 0 0)/CO

The local adsorption geometry of CO adsorbed in different states on Ni(1 0 0) and on Ni(1 0 0) precovered with atomic hydrogen has been determined by C 1s (and O 1s) scanned-energy mode photoelectron diffraction, using the photoelectron binding energy changes to characterise the different states. The results confirm previous spectroscopic assignments of local atop and bridge sites both with and without coadsorbed hydrogen. The measured Ni–C bondlengths for the Ni(1 0 0)/CO states show an increase of 0.16 ± 0.04 Å in going from atop to bridge sites, while comparison with similar results for Ni(1 1 1)/CO for threefold coordinated adsorption sites show a further lengthening of the bond by 0.05 ± 0.04 Å. These changes in the Ni–CO chemisorption bondlength with bond order (for approximately constant adsorption energy) are consistent with the standard Pauling rules. However, comparison of CO adsorbed in the atop geometry with and without coadsorbed hydrogen shows that the coadsorption increases the Ni–C bondlength by only 0.06 ± 0.04 Å, despite the decrease in adsorption energy of a factor of 2 or more. This result is also reproduced by density functional theory slab calculations. The results of both the experiments and the density functional theory calculations show that CO adsorption onto the Ni(1 0 0)/H surface is accompanied by significant structural modification; the low desorption energy may then be attributed to the energy cost of this restructuring rather than weak local bonding.     

Synthesis of Dimethyl Carbonate from CO2 , Methanol, and Epoxides Using Re（CO） 5 Cl/K2 CO3 as Catalyst System

IntroductionOver the past few years, dimethyl carbonate(DMC) has been proven to be an efficientmethylating,methoxylating, and methoxycarbonylating agent inorganic syntheses, in which DMC is used to replace thetoxic methyl halides, dimethyl sulfate or carb     

Simulation and fabrication of carbon nanotubes field emission pressure sensors

A novel field emission pressure sensor has been achieved utilizing carbon nanotubes (CNTs) as the electron source. The sensor consists of the anode sensing film fabricated by wet etching process and multi-wall carbon nanotubes (MWNTs) cathode in the micro-vacuum chamber. MWNTs on the silicon substrate were grown by thermal CVD. The prototype pressure sensor has a measured sensitivity of about 0.17-0.77 nA/Pa (101-550 KPa). The work shows the potential use of CNTs-based field-emitter in microsensors, such as accelerometers and tactile sensors.     

电子辐照诱发固态相变导致的氮化硼纳米结构生长

报道了N+离子轰击产生的氮化硼(BN)纳米结构,及在电子辐照时结构演化的高分辨透射电子显微镜的原位测定结果.应当强调的是,这种类富勒烯和发夹结构的演化,实际上是电子辐照诱发固态相变的发展,观察中发现的一些BN颗粒、卷曲物,可以被认为是类富勒烯等纳米结构形成的前体或早期阶段.提出了一种类富勒烯等结构的电子辐照动力学模型,并进行了讨论. 关键词： 氮化硼 电子辐照 透射电子显微镜 氮化硼纳米形成物