Enhancing signal-to-noise ratio and resolution in low-field NMR relaxation measurements using post-acquisition digital filters

The traditional way to enhance signal-to-noise ratio (SNR) of nuclear magnetic resonance (NMR) signals is to increase the number of scans. However, this procedure increases the measuring time that can be prohibitive for some applications. Therefore, we have tested the use of several post-acquisition digital filters to enhance SNR up to one order of magnitude in time domain NMR (TD-NMR) relaxation measurements. The procedures were studied using continuous wave free precession (CWFP-T₁) signals, acquired with very low flip angles that contain six times more noise than the Carr–Purcell–Meiboom–Gill (CPMG) signal of the same sample and experimental time. Linear (LI) and logarithmic (LO) data compression, low-pass infinity impulse response (LP), Savitzky–Golay (SG), and wavelet transform (WA) post-acquisition filters enhanced the SNR of the CWFP-T₁ signals by at least six times. The best filters were LO, SG, and WA that have high enhancement in SNR without significant distortions in the ILT relaxation distribution data. Therefore, it was demonstrated that these post-acquisition digital filters could be a useful way to denoise CWFP-T₁, as well as CPMG noisy signals, and consequently reducing the experimental time. It was also demonstrated that filtered CWFP-T₁ method has the potential to be a rapid and nondestructive method to measure fat content in beef and certainly in other meat samples.     

基于图像处理技术的束流剖面监视系统

 介绍了在兰州重离子加速器上利用荧光靶图像获取装置测量并计算束流剖面参数的方法，并建立了图像获取、处理、束流参数计算的实时测量软件系统。该系统具有可靠性好、测量直观、界面友好等优点。     

热声驱动系统中的压力测量

介绍了自制的用于热声驱动脉管制冷装置的计算机压力波数据采集系统。该系统由硅压电压力传感器、数据采集卡、PC机和基于 Labview软件的图形化用户界面 GUI( Graphical User In-terface)组成。试验证明 ,它具有结构简单、高效精确、操作简便等特点 ,在捕捉被测系统内的动态压力变化方面具有优势 ,不但能很好地满足热声驱动器的压力测量要求 ,而且亦可移植到任何类似的测量气体压力的场合     

基于EPP协议的便携机数据采集系统

设计了基于EPP协议的便携机数据采集系统 ,给出了技术解决方案。方案具有软硬件设计简捷、无需插卡等优点 ,可使外设工作于PC并行口的多种模式下。解决了线阵CCD图像采集系统与笔记本电脑之间的数据通讯 ,达到了便携数据采集的目的。     

Comparison of methods to enhance flame ionization detector (FID) signals in gas chromatography

The performances of some numerical methods to improve the signal to noise ratio are compared and applied to enhance noisy signals obtained in gas chromatography with capillary columns and a flame Ionization detector. Several methods have been considered: cutoffs In the Fourier transform of the recorded signal; real time numerical filtering; theoretical model curve fitting; and the correlation of a chromatogram recorded from a pseudorandomly injected sample with the pseudorandom injection function. Numerical real time filtering is shown to be the most convenient method when the main periodic component of the noise has been determined by Fourier analysis.     

Characterization of the road surfaces in real time

The main factor in the propagation of traffic noise is the road surface, where the vehicles generate noise due to the contact between tire and pavement, in addition to the noise produced by the engine.     

Practical guide for selection of 1H qNMR acquisition and processing parameters confirmed by automated spectra evaluation

In our recent paper, a new technique for automated spectra integration and quality control of the acquired results in qNMR was developed and validated (Monakhova & Diehl, Magn. Res. Chem. 2017, doi: 10.1002/mrc.4591 ). The present study is focused on the influence of acquisition and postacquisition parameters on the developed automated routine in particular, and on the quantitative NMR (qNMR) results in general, which has not been undertaken previously in a systematic and automated manner. Results are presented for a number of model mixtures and authentic pharmaceutical products measured on 500‐ and 600‐MHz NMR spectrometers. The influence of the most important acquisition (spectral width, transmitter [frequency] offset, number of scans, and time domain) and processing (size of real spectrum, deconvolution, Gaussian window multiplication, and line broadening) parameters for qNMR was automatically investigated. Moderate modification of the majority of the investigated parameters from default instrument settings within evaluated ranges does not significantly affect the trueness and precision of the qNMR. Lite Gaussian window multiplication resulted in accuracy improvement of the qNMR output and is recommended for routine measurements. In general, given that the acquisition and processing parameters were selected based on the presented guidelines, automated qNMR analysis can be employed for reproducible high‐precision concentration measurements in practice.     

基于CAN总线的某型数字化战车自动测试系统设计

针对现代数字化战车电气与电子系统技术复杂、各分系统关联程度高、维修保障困难等问题,设计了一种基于CAN总线的数字化战车自动测试系统;整体设计基于模块化思想,充分利用车载备用总线,综合运用了DSP+FPGA控制处理技术、AFPN智能故障诊断技术,能够对车载电气与电子系统进行分系统独立测试和全系统联合检测,具有快速故障定位能力和拓扑适应能力;采用适配器与上位机测试软件的分体式设计,实现了平台物理资源复用。应用表明,该系统能够较好的适用于现代数字化战车的维修保障,使用方便,故障诊断快速有效。     

夜视战场环境视觉传感信息采集系统设计

夜视战场环境视觉传感信息的实时获取是跟踪夜视战场图像处理分析的前提,针对夜视战场环境的复杂特征,设计了夜视战场环境视觉传感信息采集系统,分析了系统的总体结构,系统硬件主要包括视觉传感器、传感器控制卡和扩展卡、图像采集与存储以及信号调理电路,给出了系统采集节点的程序设计流程以及传感信息采集的具体程序代码实现过程。实验结果说明,所设计系统可有效采集到夜间军事战场中的传感信息,并且具有较高的采集精度。