相位校正器粘接局部应力控制技术

通过理论分析,对相位校正器的镜面与支撑结构间的粘接建立模型进行仿真研究,提出了在相位校正器镜片上加工小圆柱,使其粘接应力由镜片本身转移到突出部位的小柱子上,有效改善了相位校正器镜面局部粘接应力,使镜面局部高阶像差得到缓解,并通过试验验证了其有效性。     

甲基紫掺杂聚乙烯醇薄膜材料红光多重全息存储

甲基紫掺杂聚乙烯醇薄膜材料在两束相干光照射下生成相位光栅.当改变一束相干光光程,通过监测相位光栅的一级衍射信号强度的变化,可以检测相位光栅的生长和擦除过程.在此实验基础上,讨论了甲基紫掺杂聚乙烯醇薄膜材料多重全息存储的原理与结果.     

BEPCII直线加速器相控系统设计研究

为了补偿由于各种因素引起的微波相位漂移,BEPCII直线加速器需要建立微波相位反馈控制系统.能量最大法将用来确定每台功率源的最佳相位.沿直线加速器速调管长廊铺设相位稳定同轴线提供相位参考.现在已经完成了关键部件,如PAD单元、IfA 单元的开发.搭建了相控最小系统对系统进行了验证.     

光纤光栅选频掺Yb3+双包层光纤激光器

利用相位掩模法 ,在D形内包层掺Yb3 双包层光纤一端直接写制出Bragg光栅 ,用作双包层光纤激光器的输出腔镜 .试验得到了线宽为 0 196nm ,波长为 10 5 8 2nm ,最高输出功率为 5 70mW的稳定激光输出 ,解决了激光器中模式竞争造成的输出不稳定现象 .从速率方程出发 ,对激光器的输出功率与抽运功率、光栅反射率的关系以及最佳光纤长度进行了理论分析 ,结果与实验符合很好     

X波段六腔渡越管振荡器的高频特性研究

 从麦克斯韦方程出发，采用时域有限差分法（FDTD）和离散傅里叶变换（DFFT）相结合的方法，通过数值计算得出了六腔开放式谐振腔中前四个谐振频率和场分布，计算出的谐振频率与实验测量结果基本相同。比较了开放腔和封闭腔谐振频率，验证了TEM波吸收边界条件，并在实际编程计算中得以应用。计算结果为六腔渡越管振荡器的机理研究提供了依据。     

Local Prediction of Chaotic Time Series Based on Support Vector Machine

Based on phase space delay-coordinate reconstruction of a chaotic dynamics system, we propose a local prediction of chaotic time series using a support vector machine （SVM） to overcome the shortcomings of traditional local prediction methods. The simulation results show that the performance of this proposed predictor for making onestep and multi-step prediction is superior to that of the traditional local linear prediction method and global SVM method. In addition, it is significant that its prediction performance is insensitive to the selection of embedding dimension and the number of nearest neighbours, so the satisfying results can be achieved even if we do not know the optimal embedding dimension and how to select the number of nearest neighbours.     

High-Average-Power Nanosecond Quasi-Phase-Matched Single-Pass Optical Parametric Generator in Periodically Poled Lithium Niobate

A pulsed nanosecond optical parametric generator (OPG) in periodically poled lithium niobate (PPLN) crysal is presented. The pump laser is an acousto-optically Q-switched Nd:YVO4 laser with the maximum average power of 6.58 W. When the repetition rate is 50kHz and the pulse width of the pump source is 80ns, the maximum average total output power of the single-pass PPLN OPG is about 1.9 W, which includes 1.322 W of 1.536μm signal radiation. The length of the PPLN crystal is only 38.7mm (at room temperature) with a grating period of 28.93μm (at room temperature). The 1.502-1.536μm signal radiation and 3.652-3.465μm idler radiation are obtained by adjusting the PPLN crystal temperature from 155℃ to 250℃.     

用相位调制方法测量光盘盘基应力双折射的精度分析

偏振相位调制方法是测量微小双折射的一种高精度检测方法。本文系统全面地分析了以ＰＭＣＳＡ结构形式测量光盘盘基应力双折射的相位调制方法中，由各种误差源造成的对测试结果的影响。     

介质极化的瞬时相位与振幅

求解电子运动的二阶微分方程，在旋转波近似下，介质在外场突然变化时产生的瞬态感应极化与外场同频，但相位总是落后，最大落后为π/2；振幅大小与初态有关，随时间按指数规律衰减，衰减快慢由介质的阻尼系数决定。     

A Movable-Cavity Cold Atom Space Clock

We present an experimental scheme of a cold atom space clock with a movable cavity. By using a single microwave cavity, we find that the clock has a significant advantage, i.e. the longitudinal cavity phase shift is eliminated. A theoretical analysis has been carried out in terms of the relation between the atomic transition probability and the velocity of the moving cavity by taking into account the velocity distribution of cold atoms. The requirements for the microwave power and its stability for atomic π/2 excitation at different moving velocities of the cavity lead to the determination of the proper working parameters of the rubidium clock in frequency accuracy 10^-17. Finally, the mechanical stability for the scheme is analysed and the ways of solving the possible mechanical instability of the device are proposed.