纳米级精度分光路双频干涉度量系统的设计

为完成快速、精确的外观轮廓度量,设计了一种新型纳米级精度分光路双频干涉度量系统。系统由低频差双频激光干涉度量模块和微探头及二维工作台两部分组成。微探针以轻敲式接近样品至几十纳米时,受原子力作用发生偏转,利用双频干涉模块度量其纵向偏转量,并对样品进行梳状式度量得到外观形貌。根据双频激光的实际光源,对原有双频干涉度量理论进行了改进提高。进行了系统组建和实验验证。结果表明:系统具有纳米级精度,可用于超精样品外观轮廓度量。     

Eu- and Yb-induced reconstructions on a vicinal Si(1 0 0) surface

Early stages of rare-earth metal (Yb and Eu) growth on a vicinal, single-domain Si(1 0 0)2 × 1 surface have been studied in the coverage range of 0.1-0.3 monolayer (ML) by low energy electron diffraction, scanning tunneling microscopy, and synchrotron radiation photoemission spectroscopy. We show that Yb induces the 2 × 3 periodicity in the whole range of coverage studied. The 2 × 3 reconstruction coexists with the local 3 × 2/4 × 2 structure at about 0.2 ML of Yb. In contrast, Eu forms the 3 × 2 periodicity at 0.1-0.2 ML, whereas this structure is converted into the 2 × 3 phase at about 0.3 ML. The atomic arrangement and electronic properties of these reconstructions and the adsorbate-mediated modification of surface morphology are investigated.     

Local adsorption sites and bondlength changes in Ni(1 0 0)/H/CO and Ni(1 0 0)/CO

The local adsorption geometry of CO adsorbed in different states on Ni(1 0 0) and on Ni(1 0 0) precovered with atomic hydrogen has been determined by C 1s (and O 1s) scanned-energy mode photoelectron diffraction, using the photoelectron binding energy changes to characterise the different states. The results confirm previous spectroscopic assignments of local atop and bridge sites both with and without coadsorbed hydrogen. The measured Ni–C bondlengths for the Ni(1 0 0)/CO states show an increase of 0.16 ± 0.04 Å in going from atop to bridge sites, while comparison with similar results for Ni(1 1 1)/CO for threefold coordinated adsorption sites show a further lengthening of the bond by 0.05 ± 0.04 Å. These changes in the Ni–CO chemisorption bondlength with bond order (for approximately constant adsorption energy) are consistent with the standard Pauling rules. However, comparison of CO adsorbed in the atop geometry with and without coadsorbed hydrogen shows that the coadsorption increases the Ni–C bondlength by only 0.06 ± 0.04 Å, despite the decrease in adsorption energy of a factor of 2 or more. This result is also reproduced by density functional theory slab calculations. The results of both the experiments and the density functional theory calculations show that CO adsorption onto the Ni(1 0 0)/H surface is accompanied by significant structural modification; the low desorption energy may then be attributed to the energy cost of this restructuring rather than weak local bonding.     

Surface morphologies of anthracene single crystals grown from vapor phase

The morphologies and lattice structures of anthracene single crystals grown from the vapor phase were investigated using optical microscopy, phase contrast microscopy, atomic force microscopy (AFM), and X-ray diffraction analysis. Common morphologies with hexagonal large planes were observed irrespective of crystal size. The observation of certain surface morphologies with a phase contrast microscopy revealed that the spiral steps originated from screw dislocations present on the (0 0 1) planes. Moreover, the center and edge of the (0 0 1) planes had large curvatures, similar to hills. Resultantly, quarter-monolayer (ML) steps were observed on the large and flat planes between both hills.     

Photoemission study of the modification of the electronic structure of transition-metal overlayers on TiO2 surfaces II. Cr on TiO2(0 0 1)

The electronic states of the Cr overlayers on TiO₂(0 0 1) surfaces have been investigated using angle-resolved and resonant photoemission spectroscopy with synchrotron radiation. At lower coverages, Cr deposition on TiO₂(0 0 1) creates two well separated in-gap emissions due to the formation of surface Ti³⁺ (3d¹) ions and Cr³⁺ (3d³) ions. At higher coverages, the in-gap emission is developed into the 2-peak-structure emission of Cr 3d character. The corresponding state is considered to be of metallic nature from the viewpoint of the high ability of oxygen adsorption, but has no Fermi edge, indicating a possibility of forming small Cr clusters on TiO₂(0 0 1) at this stage.     

First-principles study of indium on silicon (1 0 0)—the structure, defects and interdiffusion

The atomic structures of indium (In) on silicon (Si) (1 0 0)-(2 × 1) surface are investigated by the local density approximation using first-principles pseudopotentials. Total energy optimizations show that the energetically favored structure is the parallel ad-dimer model. The adsorption energy of In on ideal Si(1 0 0)-(1 × 1) surface is significantly higher than that on reconstructed Si(1 0 0)-(2 × 1) surface, suggesting that In adsorption does not break the Si-Si dimer bond of the substrate. When Si surface contains single dimer vacancy defects, In chain will be interrupted, leading to disconnected In nanowires. Displacive adsorption of In on Si(1 0 0) is also considered, and the calculation suggests that interdiffusion of In into Si substrate will not be favorable under equilibrium conditions.     

The moire topography based on optical logic operation

The optical logic-operated moire,which is proposed on the basis of optical logicoperation,is a new method to obtain specific moire beat pattern.Its advantages lie in the ca-pability to select carrier-free,sharpened fringes with high contrast.The experimental methodand results of the application of the optical logic-operared moire in moire topography are pre-sented in this paper.     

AFM, SEM and GIXRD studies of thin films of red polycarbazolyldiacetylenes

In this paper we report the results of a morphological and structural investigation on film properties of a soluble polydiacetylene, the poly[1,6-bis(3,6-dihexadecyl-N-carbazolyl)-2,4-hexadiyne] (polyDCHD-HS). The red films of this polymer, prepared by standard spin-coating techniques, revealed absence of linear dichroism and birefringence in contrast with the ordered mesophases detected by powder X-ray studies. In order to interpret the optical behavior of this polymer, we performed AFM and SEM studies of polyDCHD-HS films spun on hydrophylic and hydrophobic glass substrates. We found the presence of surfaces organized in rod-like particles, more regularly oriented on the hydrophylic substrate. GIXRD studies, carried out on films sufficiently thick to allow the observation of the diffraction pattern, reveled the presence of a lamellar structure with a spacing of 3.22 nm. The low intensity of the diffraction peaks and the isotropic linear optical properties of the films show that the lamellar mesophases are not extended over large areas. These findings were compared with the data obtained from AFM and SEM studies on films of two other polydiacetylenes, the poly[1-(3,6-dihexadexyl-N-carbazolyl)-6-(N-carbazolyl)-2,4-hexadyine] (polya-DCHD) and the poly[1,6-bis(3,6-dipalmitoyl-N-carbazolyl)-2,4-hexadyine] (polyDPCHD), spun on hydrophylic glass substrate. The results confirmed the presence of nodular morphologies which seem to be a general characteristic of this class of materials. The particles organization appears instead related to the chemical nature of the substituents on the carbazolyl rings.     

Scanning probe microscopy studies of PbS surfaces oxidized in air and etched in aqueous acid solutions

Natural n-type PbS single crystals have been studied using AFM, STM and STS after long-term oxidation in air at ambient temperatures and extensive etching in aqueous acid solutions, in contrast to previous work devoted to initial corrosion of fresh surfaces. The exposure of PbS to atmosphere at high relative humidity for several days yields widespread loose oxidation products; the process is much slower at low humidity. Surface morphologies diverge after the treatment in 1 M perchloric and hydrochloric acid solutions at room temperature and become widely different at elevated temperatures, displaying commonly etch pits up to several micrometers in size and depth along with rather uniformly distributed 20-100 nm protrusions of PbS phase. The changes both in topography and semiconducting properties of PbS found by tunneling spectroscopy have been explained in terms of the non-uniform distribution of donor- and acceptor-type defects D⁺/D⁻ in the metal depleted surface layer, which are generated by chemical reactions and, in turn, determine the rates of the PbS corrosion. In particular, the D⁻ centers exhibit a self-catalyzing effect on the non-oxidative local dissolution of PbS in HCl media, resulting in the deep etch pits.     

Solved and unsolved problems in surface structure determination

The range of surface structural problems of interest in understanding the physics and chemistry of solid surfaces is reviewed with reference to the available methods and their strengths and limitations. Key challenges being addressed currently concern the achievable precision of measurements and their physical and chemical significance, and the complexity of the problems which may be solved. Past progress and future problems are illustrated with a series of examples ranging from the relaxation of simple clean metal surfaces through complex semiconductor reconstructions to large molecular adsorption and coadsorption systems and complex adsorbate-induced reconstructions. The strengths and limitations of scanning tunnelling microscopy as a complement to true quantitative structural methods are discussed, as is the role of chemical state specificity and elemental specificity in solving complex molecular adsorbate systems.