Linearization of column responses by correlation chromatography. Separation improvement and reduction of undesired adsorption effects

Summary Experiments and simulations prove that correlation chromatography can greatly reduce the disadvantage of a non-linear response of the chromatographic column. A factor that has been accepted as being an important source of error in correlation or multiplex chromatography, has been shown not to be. Separations affected, improve dramatically when correlation chromatography is used, and a substantial amount of correlation noise only arises when there is a large difference in separation between a conventional chromatogram and a correlogram.A model has been developed for simulating these nonlinearities. It is shown that, especially for correlation chromatography, the simulation results match the practical measurements very well.     

对超重、失重演示实验的改进

对传统的超重、失重演示实验进行了改进,使弹簧秤的指针能静止在超重(或失重)的位置上,从而能准确地读出读数,提高演示效果.     

Calibrating software reliability models when the test environment does not match the user environment

Software failures have become the major factor that brings the system down or causes a degradation in the quality of service. For many applications, estimating the software failure rate from a user's perspective helps the development team evaluate the reliability of the software and determine the release time properly. Traditionally, software reliability growth models are applied to system test data with the hope of estimating the software failure rate in the field. Given the aggressive nature by which the software is exercised during system test, as well as unavoidable differences between the test environment and the field environment, the resulting estimate of the failure rate will not typically reflect the user‐perceived failure rate in the field. The goal of this work is to quantify the mismatch between the system test environment and the field environment. A calibration factor is proposed to map the failure rate estimated from the system test data to the failure rate that will be observed in the field. Non‐homogeneous Poisson process models are utilized to estimate the software failure rate in both the system test phase and the field. For projects that have only system test data, use of the calibration factor provides an estimate of the field failure rate that would otherwise be unavailable. For projects that have both system test data and previous field data, the calibration factor can be explicitly evaluated and used to estimate the field failure rate of future releases as their system test data becomes available. Copyright © 2002 John Wiley & Sons, Ltd.     

Comparison of two models for managing reliability growth during product design

Relying on reliability growth testing to improve system designis neither usually effective nor efficient. Instead it is importantto design in reliability. This requires models to estimate reliabilitygrowth in the design that can be used to assess whether goalreliability will be achieved within the target timescale forthe design process. Many models have been developed for analysisof reliability growth on test, but there has been much lessattention given to reliability growth in design. This paperdescribes and compares two models: one motivated by the practicalengineering process; the other by extending the reasoning ofstatistical reliability growth modelling. Both models are referencedin the recently revised edition of international standard IEC61164. However, there has been no reported evaluation of theirproperties. Therefore, this paper explores the commonalitiesand differences between these models through an assessment oftheir logic and their application to an industrial example.Recommendations are given for the use of reliability growthmodels to aid management of the design process and to informproduct development.     

一种基于图论与熵的专家判断客观可信度的确定方法

本文给出一种群决策中确定专家判断可信度的方法，其主要思路是首先通过图论中最小生成树的方法提取专家判断矩阵的全部信息，其次，使用相对熵指标确定获得专家判断的最终结果，并同时衡量专家自身判断的统一程度，从而确定专家判断的相对客观可信度。最后，文章给出一个典型的算例以说明该方法的可行性和有效性。     

简析"静止液体内部压强公式验证"实验的设计策略

“静止液体内部压强公式验证”在现行教材中有两种实验方法。通过分析实验的设计策略，说明其作用、效果及操作上的困难，指出合理的与不合理诸因素，从而提出改进实验的方法，化难为易，提高实验教学效果。     

Global Optimization of Stochastic Black-Box Systems via Sequential Kriging Meta-Models

This paper proposes a new method that extends the efficient global optimization to address stochastic black-box systems. The method is based on a kriging meta-model that provides a global prediction of the objective values and a measure of prediction uncertainty at every point. The criterion for the infill sample selection is an augmented expected improvement function with desirable properties for stochastic responses. The method is empirically compared with the revised simplex search, the simultaneous perturbation stochastic approximation, and the DIRECT methods using six test problems from the literature. An application case study on an inventory system is also documented. The results suggest that the proposed method has excellent consistency and efficiency in finding global optimal solutions, and is particularly useful for expensive systems.     

一类二元相关威布尔分布的可靠性问题

本文考虑生存函数为${\ol{F}(x_{1},x_{2})}=\exp\{-[(x_{1}^{1/\alpha}/\theta_{1})^{1/\delta}+(x_{2}^{1/\alpha}/\theta_{2})^{1/\delta}]^{\delta}\},\;x_{i}>0,\;\alpha>0$, $1\geq\delta>0,\;\theta_{i}>0\;(i=1,2)$的二元威布尔分布的两种可靠性问题, 提出可靠度$\pr$的估计并讨论了它们的渐近性, 最后还作了模拟计算.     

Low noise double pass L-band erbium-doped fiber amplifier

A new double pass long wavelength band erbium-doped fiber amplifier with enhanced noise figure characteristics is demonstrated. The noise figure is improved by about 2.6 dB with the incorporation of broadband conventional-band fiber Bragg grating (FBG) in between the two segments of erbium-doped fiber. By incorporating both the pre-amplifier and the FBG, the noise figure is further improved, which varies from 4.0 to 5.0 dB in the flat gain region from 1570 to 1600 nm. The gain varies from 32.0 to 33.4 dB within this region. The new amplifier with high gain and low noise figure can be useful as an inline amplifier in a wavelength division multiplexing transmission system.     

抽样调查中最佳测量次数的确定

现场抽样调查中，由于测量误差的存在，使得所测变量实测值的方差增大，通过增加每个体的测量次数可以控制测量误差，但这样每个体调查费用增大。本文对测量信度Ｒ，每个体测量次数ｍ与相应所需的样本含量ｎｍ、调查费用Ｔｎ的关系进行了探讨，并介绍了如何根据Ｒ，及每个体测量费用占其总费用构成比Ｃ，确定最佳测量次数ｍ值，以达到最佳控制调查费用的目的，这对我们在大型现场调查中进行经济效益分析具有重大的理论指导意义。