Effect of pressure on the low-temperature reaction of ethylene with N2O4

Calorimetric monitoring of the autoclave reaction N₂O₄ + C₂H₄ at –85 to +10 °C under argon pressure 10–30 bar revealed that the exothermic chemical reaction started at temperatures above –52 °C at 10 bar, whereas an intensive exothermic reaction started at –85 °C and pressure of 30 bar. IR study showed that oligo/polynitroethylene was formed at 30 bar, while carbonyl and hydroxy compound as well as nitrate R–ONO₂ formation occurred upon processing at 10 bar.     

坚硬顶板爆破切顶在沿空留巷中的应用研究

当煤层上方为坚硬顶板时,在工作面回采期间容易出现大面积悬顶,导致巷旁充填体出现大变形破坏,极大威胁采煤安全.为解决这一问题,以某矿1205工作面沿空留巷为工程背景,分析了爆炸围岩裂隙范围和坚硬顶板破断特征,建立了切顶卸压围岩结构力学模型,研究表明,相邻炮孔爆炸后,炮孔间裂隙互相贯穿,降低了顶板强度,同时当切顶角为15°时,巷道稳定性较好.工程实践结果表明:采用爆破切顶技术后,顶板下沉量减小了62.3%,较好地保证了围岩稳定性.     

Synthesis of nano-polycrystalline diamond from glassy carbon at pressures up to 25 GPa

ABSTRACT

Nano-polycrystalline diamond (NPD) with various grain sizes has been synthesized from glassy carbon at pressures 15–25?GPa and temperatures 1700–2300°C using multianvil apparatus. The minimum temperature for the synthesis of pure NPD, below which a small amount of compressed graphite was formed, significantly increased with pressure from ～1700°C at 15?GPa to ～1900°C at 25?GPa. The NPD having grain sizes less than ～50?nm was synthesized at temperatures below ～2000°C at 15?GPa and ～2300°C at 25?GPa, above which significant grain growth was observed. The grain size of NPD decreases with increasing pressure and decreasing temperature, and the pure NPD with grain sizes less than 10?nm is obtained in a limited temperature range around 1800–2000°C, depending on pressure. The pure NPD from glassy carbon is highly transparent and exhibits a granular nano-texture, whose grain size is tunable by selecting adequate pressure and temperature conditions.     

Semilinear wave models with friction and viscoelastic damping

In this paper, we study the global (in time) existence of small data solutions to the Cauchy problem for the semilinear wave equation with friction, viscoelastic damping, and a power nonlinearity. We are interested in the connection between regularity assumptions for the data and the admissible range of exponents p in the power nonlinearity.     

为什么要引入溶剂的渗透因子

阐明了引入溶剂渗透因子的必要性,较详细地介绍了两种渗透因子及它们间的关系。     

含气率对PTS时压力容器内流动与传热的影响

本文对反应堆压力容器紧急安注时的流动与传热特性在1/10的模型上进行了流动可视化、局部传热系数以及混合函数的试验研究。针对三个热冲击敏感区域的部分测点,比较了环腔流速为0.5m/s、安注流速为1～30 m/s时不同含气率对下降环腔内流动与传热特性的影响,得出并分析了不同测点传热系数、混合函数的变化规律。研究结果表明:随着含气率增大,安注流体与环腔流体的混合增强;下降环腔内的含气率对小安注流速时的流动与传热影响显著,而对大安注流速时影响较小。     

非线性互补问题的一种全局收敛的显式光滑Newton方法

本针对Po函数非线性互补问题，给出了一种显式光滑Newton方法，该方法将光滑参数μ进行显式迭代而不依赖于Newton方向的搜索过程，并在适当的假设条件下，证明了算法的全局收敛性。     

Efficient Collocation Schemes for Singular Boundary Value Problems

We discuss an error estimation procedure for the global error of collocation schemes applied to solve singular boundary value problems with a singularity of the first kind. This a posteriori estimate of the global error was proposed by Stetter in 1978 and is based on the idea of Defect Correction, originally due to Zadunaisky. Here, we present a new, carefully designed modification of this error estimate which not only results in less computational work but also appears to perform satisfactorily for singular problems. We give a full analytical justification for the asymptotical correctness of the error estimate when it is applied to a general nonlinear regular problem. For the singular case, we are presently only able to provide computational evidence for the full convergence order, the related analysis is still work in progress. This global estimate is the basis for a grid selection routine in which the grid is modified with the aim to equidistribute the global error. This procedure yields meshes suitable for an efficient numerical solution. Most importantly, we observe that the grid is refined in a way reflecting only the behavior of the solution and remains unaffected by the unsmooth direction field close to the singular point.     

一类非线性抛物型变分不等方程的全局吸引子及弱近似惯性流形

对由一类非线性抛物型变分不等方程所描述的无穷维动力系统，给出了存在全局吸引子及弱近似惯性流形的充分条件．     

压力淬火过程中锗的相结构研究

 应用高压原位差热方法，直接测量了压力下锗的固化参数─—固化温度与过冷度。高压差热信号表明，当压力大于3 GPa时，锗在凝固过程中可能发生结构相变。X射线结构分析表明，在最终的样品中除GeⅠ相外，还形成GeⅢ相和GeⅣ相。