混合溶剂中性载体镁离子选择性微电极的研究

用氯化石腊和邻硝基苯辛醚为混合溶剂制备中性载体ETH5214的镁离子选择性微电极,相对于钾离子的电位选择性系数较单独以邻硝基苯辛醚为溶剂的ETH5214镁微电极改善0.9个数量级。在纯MgCl~2和在含细胞内典型离子背景的MgCl~2溶液中,响应斜率为Nernst响应,检测下限分别为4×10^-^7mol.dm^-^3和2×10^-^5mol.dm^-^3。在pH3.5-9.5范围内,氢离子对电极的电位响应无影响。测量的重现性良好。电极的实用响应时间(t~9~5)≤3s,有效寿命长于5天。     

γ干扰素免疫电极及其响应机理的研究

在醋纤维孔膜上利用溴化氰固定了马抗人γ干扰素抗体。抗体膜经竞争性温育反应后置于碘离子选择电极上而构成免疫电极; 另一碘电极与参比膜作为参比电极。测定了电极在0.1mmol.dm^-3KI+4.4mmol.dm^-3H2O2+0.1mol.dm^-3柠檬酸盐,PH5.0缓冲液中响应电位, 研究了温度反应时间、电解液组成等因对电极响应影响,提出了电极向应线性化方法, 并得到了实验验证。     

Can an Unruh Detector Feel a Cosmic String?

Unruh's detector calculation is used to study the effect of the defect angle in a space-time with a cosmic string for both the excitation and deexcitation cases. It is found that a rotating detector results in a non-zero effect for both finite (small) and infinite (large) time.     

化学镀镍诱发过程的研究 II.用电子能谱研究诱发过程

In the previous paper, it was reported that a sudden decrease down to -0.6V and lower in stationary potential was observed from the stationary potential-time curve and the reaction of electroless nickeling could be induced by metallic iron catalyst when it was in contact with substrate metallic copper. In this paper, AES and XPS surface analysis and depth profile technique was employed to investigate the surface and depth distribution of Ni, Cu, Fe and P in the nickel coating deposited on the substrate metal. The experimental results showed that there was a thin adsorption layer consisting of C, S and Cl. The pure electroless nickel deposition, its Ni/P ratio being about two, existed under the adsorption layer. A layer with rapidly changed Ni/P ratio occurred close to the surface of substrate metal, under this layer the substrate metal was alloyed with Ni and P, thus becoming Cu-Ni-P alloy. The ratio of components in this alloy was found to be Cu:Ni:P=56:36:5. This fact explained why the electroless nickel deposition can preferably adhered to the substrate metal. In inducing process, Fe was not detected by AES from the substrate metal and nickel deposition. Thus it showed that the inducing reaction takes place without the deposition of inducing metal.     

Thermal Degradation Behavior,Permeation Properties and Impact Response of Polyethylene/Organo-montmorillonite/(Ethylene Methacrylic Acid) Ternary Nanocomposites

Through this work we explored the effect of melt compounding a commercial grade of HDPE with organoclays of different precedence using EMAA as compatibilizing agent on the thermal behavior, barrier properties and biaxial impact response of composites. Morphology was examined by XRD and TEM. Crystalline structure was examined by DSC. Thermal behavior was evaluated by TGA. Barrier properties to low-molecular-weight penetrants were experimentally determined employing a gravimetric technique. Mechanical properties under impact conditions were evaluated by instrumented puncture tests. Intercalated nanocomposites were obtained. Throughout the thermal degradation of the nanocomposites in oxidant atmosphere a charring process of the PE, which is normally a non-char-forming polymer, was observed. The addition of OMMT improves barrier properties due to its contribution to tortuosity path and to the reduction of molecular mobility. Impact properties were only slightly reduced by nanocomposite formation. Results demonstrate that EMAA did not improve exfoliation, but it enhanced polymer–organoclay interactions giving rise to better thermal and permeation properties, without detriment of impact response.     

化学镀镍诱发过程的研究 I:金属催化活性的鉴别和反应机理

Electroless plating is known to be an autocatalytic process. For the reaction to start, the substrate metall should be either catalytic or activated by a suitable catalyst. For example, steel and nickel can be plated directly, but in the case of copper or brass, catalytic metal inducing is need. In this paper, the catalytic activity of different metals and their inducing effects were in vestigated by measuring stationary potentials nd stationary potential-time curves. Experimental results showed: (1) The stationary potential of metal provides a simple parameter to estimate the catalytic activity of metals in electroless nickeling. When 1-hydroxyethylidenediphosphonic acid (HEDP) aelectroless nickeling bath containing NaH2PO2 as reducing agent is used, electrolessnickeling may proceed spontaneously, if the stationary potential of metal is more nagative than -0.60V, no matter whether nickel (autocatalytic active) or other metals(non-autocatalytic active) is used as substrate. (2)When an autocatalytic meta is in contact with the substrate metal in the bath, a sudden decrease of stationary potential is observed. The whole inducing process could be finished within 0.5-2 sec. (3) The stationary potential of electroless nickeling coating in HEDP bath at 80`C is-0.72V, consequently nickel coating itself is a catalytic active metal. Once an electroless nickeling coating is deposited on a substrate metal, electroless nickeling reaction can then proceed continuously. (4) The sufficient conditions of electroless nickeling in HEDP bath containing NaH2PO2 are that the stationary potential of substrate metal must be more nagative than -0.60V and that the temperature of electroless nickeling bath should be higher than 50`C. (5) Inducing mechanism of electroless nickeling can be explained with chemical cell consisting of substrate metal and catalytic metal. Electrons from catalytic metal would suddenly decrease the stationary potential of substrate metal, H+ and Ni2+ complex ion would be reduced on the substrate me     

EFFECTS OF REACTION AND PROCESSING PARAMETERS ON ETHYLENE POLYMERIZATION USING DIFFERENT ZIEGLER-NATTA CATALYSTS：EMPLOYMENT OF TAGUCHI EXPERIMENTAL DESIGN AND RESPONSE SURFACE METHOD

Different Ziegler-Natta catalysts were employed to polymerize ethylene. To investigate the influences of reaction parameters, namely Al/Ti molar ratio, hydrogen and processing parameters, i.e. ethylene pressure and temperature, a Taguchi experimental design was worked out. An L27 orthogonal array was chosen to take the above-mentioned parameters and relevant interactions into account. Response surface method was the tool used to analyze the experimental design results. Al/Ti, ethylene pressure and temperature were selected as experimental design factors, and catalyst activity and polymerization yield were the response parameters. Increasing pressure, due to an increment in monomer accessibility, and rising Al/Ti, because of higher reduction in the catalysts, cause an increase in both polymerization yield and catalyst activity. Nonetheless, a higher temperature, thanks to reducing ethylene solubility in the slurry medium and partially catalyst destruction, lead to a reduction in both response parameters. A synergistic effect was also observed between temperature and pressure. All catalyst activities will reduce in the presence of hydrogen. Molecular weight also shows a decline in the presence of hydrogen as a transfer agent. However, the polydispersity index remains approximately intact. Using SEM, various morphologies, owing to different catalyst morphologies, were seen for the polyethylene.     

EFFECTS OF GELATION RETARDATION ON THERMAL RESPONSE BEHAVIOR OF PNIAPM GELS： A METHOD TO IMPROVE THEIR DESWELLING KINETICS

P(N-isopropylacrylamide)(PNIPAM)prepared by reversible addition fragmentation chain transfer(RAFT) polymerization exhibited gelation retardation.The intermediate before gelation was characterized and indicated the presence of branched or hyperbranched chains.The swelling behavior was investigated,and the gel by RAFT polymerization(RAFT gel)showed accelerated shrinking kinetics and higher swelling ratio comparing with conventional gels(CG).The study was extended to gels prepared by using 2-hydroxy-1-ethanethiol as chain transfer agent and by using low concentration solutions. The two systems also exhibited retardation effects and improved deswelling kinetics.The different swelling behaviors of these gels and CG could be attributed to the presence of dangling chains caused by gelation retardation.