CONCEPTUAL DESIGN STUDIES OF AN 84 GHz, 500 kW, CW GYROTRON

The feasibility of an 84 GHz, 500 kW, CW gyrotron for ECRH on an experimental tokamak will be presented in this paper. Mode competition and mode selection procedures are carefully investigated by considering various candidate modes and the TE_10,4 mode is chosen as the operating mode. A conventional cylindrical cavity resonator with weak input and output tapers and parabolic roundings is considered for interaction studies. Self-consistent, both single mode and time-dependent, calculations are carried out and power and efficiencies are computed for a typical set of beam parameters. The results show that an output power of well over 500 kW, CW and efficiency around 40% can be reached without a depressed collector.     

非傍轴平顶高斯光束M2因子两种定义的比较研究

基于功率密度的二阶矩方法,推导出了非傍轴平顶高斯(FG)光束束宽和远场发散角的解析表达式·研究表明,当w0/λ→0时,远场发散角趋于渐近值θmax=63.435°,与阶数无关·使用非傍轴高斯光束代替傍轴高斯光束作为理想光束,研究了非傍轴FG光束的M2因子,并与传统定义的M2因子作了比较·在非傍轴范畴,非傍轴FG光束的M2因子不仅与阶数N有关,而且与w0/λ有关·按照定义,当w0/λ→0时,非傍轴FG光束的M2因子不等于0,对阶数N=1,2,3时,M2因子分别趋于0.913,0.882和0.886·当N→∞时,M2因子取最小值M2min=0.816·     

Synthesis and gas barrier characterization of poly(ethylene isophthalate)

Poly(ethylene isophthalate) (PEI) was synthesized for this research with essentially a condensation polymerization of isophthalic acid and ethylene glycol catalyzed by zinc acetate and antimony trioxide. Several samples were obtained, and their characteristics were observed and compared with poly(ethylene terephthalate) (PET). The synthesized PEI samples were chemically identified by ¹H NMR. Thermal analysis with differential scanning calorimetry (DSC) yielded results that indicate the samples were primarily amorphous, with a glass‐transition temperature of 55–60 °C. Molecular weights of these PEI samples were also obtained through intrinsic viscosity measurements (Mark–Houwink equation). Molecular weights varied with conditions of the polymerization, and the highest molecular weight achieved was 21,000 g/mol. Finally, the diffusion coefficient, solubility, and permeability of CO₂ gas in PEI were measured and found to be substantially lower than in PET, as anticipated from their isomeric chemical structures. This is because in PET the phenyl rings are substituted in the para (1,4) positions, which allows for their facile flipping, effectively permitting gases to pass through. However, the meta‐substituted phenyl rings in PEI do not permit such ring flipping, and thus PEI may be more suitable for barrier applications. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4247–4254, 2004     

Sol–Gel-Derived Corrosion-Protection Coatings

There is a current need for alternative coatings that can provide corrosion resistance to metals or alloy surfaces due to the environmental hazards posed by conventional coatings. Herein, we report on novel organically-modified sol–gel coatings for the protection of metal and alloy surfaces. The basic concept of chemical conversion of metal surfaces is based on deposition of a hydrophobic, nonporous sol–gel barrier layer for surface protection and corrosion prevention. The properties of these organosilica coatings can be tuned by varying the composition of precursors. The evaluation of hydrophobicity, adhesive strength, and anticorrosion properties of organically-modified sol–gel derived coatings suggests their potential utility as technologically-compatible alternatives to conventional coatings.     

Phase transformation of Ni-B, Ni-P diffusion barrier deposited electrolessly on Cu interconnect

In this paper, we report that the phase transformation of Ni-B, Ni-P diffusion barriers deposited electrolessly on Cu, for the reason that the Ni-P layer is a more effective diffusion barrier than the Ni-B layer. The Ni₃B crystallized was decomposed to Ni and B₂O₃ above 400 °C and the Ni₃P crystallized was decomposed to Ni and P₂O₅ above 600 °C respectively in Ar atmosphere. Also, the Ni₃B was decomposed to Ni and free B above 400 °C and the Ni₃P was decomposed to Ni and free P above 600 °C respectively in H₂ atmosphere. The decomposed Ni formed a solid solution with Cu. The Cu diffusion occurred above 400 °C for Ni-B layer and above 600 °C for Ni-P layer, respectively. Because the decomposition temperature of Ni-P layer is about 200 °C higher than that of Ni-B layer, the Ni-P layer is a more effective barrier for Cu than the Ni-B layer.     

Conic Formulation for l p -Norm Optimization

In this paper, we formulate the l _p -norm optimization problem as a conic optimization problem, derive its duality properties (weak duality, zero duality gap, and primal attainment) using standard conic duality and show how it can be solved in polynomial time applying the framework of interior-point algorithms based on self-concordant barriers.     

A boundary element method for the calculation of noise barrier insertion loss in the presence of atmospheric turbulence

Atmospheric turbulence is an important factor that limits the amount of attenuation a barrier can provide in the outdoor environment. It is therefore important to develop a reliable method to predict its effect on barrier performance. The boundary element method (BEM) has been shown to be a very effective technique for predicting barrier insertion loss in the absence of turbulence. This paper develops a simple and efficient modification of the BEM formulation to predict the insertion loss of a barrier in the presence of atmospheric turbulence. The modification is based on two alternative methods: (1) random realisations of log-amplitude and phase fluctuations of boundary sources and (2) de-correlation of source coherence using the mutual coherence function (MCF). An investigation into the behaviours of these two methods is carried out and simplified forms of the methods developed. Some systematic differences between the predictions from the methods are found. When incorporated into the BEM formulation, the method of random realisations and the method of MCF de-correlation provide predictions that agree well with predictions by the parabolic equation method and by the scattering cross-section method on a variety of thin barrier configurations.     

On the role of the interface charge in non-ideal metal–semiconductor contacts

The bias dependent interface charge is considered as the origin of the observed non-ideality in current–voltage and capacitance–voltage characteristics. Using the simplified model for the interface electronic structure based on defects interacting with the continuum of interface states, the microscopic origin of empirical parameters describing the bias dependent interface charge function is investigated. The results show that in non-ideal metal–semiconductor contacts the interface charge function depends on the interface disorder parameter, density of defects, barrier pinning parameter and the effective gap center. The theoretical predictions are tested against several sets of published experimental data on bias dependent ideality factor and excess capacitance in various metal–semicoductor systems.     

PV型HgCdTe光电探测器中的混沌及其诊断

 对激光辐照半导体光电探测器的实验研究，发现当一束不太强的稳定连续波激光照射在PV型HgCdTe光电探测器上时，可以引起探测器出现混沌行为。利用光电探测器的光电压信号随时间变化的实验数据，通过求功率谱、计算Lyapunov指数对混沌进行了诊断。     

Generalization of a sharp Hölder's inequality and its application

In this paper, we generalize Hu Ke's sharpness of Hölder's inequality. As application, the obtained result is used to improve the well-known Opial-Olech inequality.