Facile non‐lithographic route to highly aligned silica nanopatterns using unidirectionally aligned polystyrene‐block‐polydimethylsiloxane films

Thin films (monolayer and bilayer) of cylinder forming polystyrene‐block‐polydimethylsiloxane (PS‐b‐PDMS) were shear aligned by the swelling and deswelling of a crosslinked PDMS pad that was physically adhered to the film during solvent vapor annealing. The nanostructures formed by self‐assembly were exposed to ultraviolet‐ozone to partially oxidize the PDMS, followed by calcination in air at 500 °C. In this process, the PS segments were fully decomposed, while the PDMS yielded silica nanostructures. The highly aligned PDMS cylinders were thus deposited as silica nanolines on the silicon substrate. Using a bilayer film, the center‐to‐center distance of these features were effectively halved from 38 to 19 nm. Similarly, by sequential shear‐alignment of two distinct layers, a rhombic array of silica nanolines was fabricated. This methodology provides a facile route to fabricating complex topographically patterned nanostructures. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1058–1064     

AGE method simulations of a turbulent far‐wake compared to spectral DNS

Turbulent flow simulation methods based on finite differences are attractive for their simplicity, flexibility and efficiency, but not always for accuracy or stability. This paper demonstrates that a good compromise is possible with the advected grid explicit (AGE) method. Starting from the same initial field as a previous spectral DNS, AGE method simulations of a planar turbulent wake were carried out as DNS, and then at three levels of reduced resolution. The latter cases were in a sense large‐eddy simulations (LES), although no specific sub‐grid‐scale model was used. Results for the two DNS methods, including variances and power spectra, were very similar, but the AGE simulation required much less computational effort. Small‐scale information was lost in the reduced resolution runs, but large‐scale mean and instantaneous properties were reproduced quite well, with further large reductions in computational effort. Quality of results becomes more sensitive to the value chosen for one of the AGE method parameters as resolution is reduced, from which it is inferred that the numerical stability procedure controlled by the parameter is acting in part as a sub‐grid‐scale model. Copyright © 2002 John Wiley & Sons, Ltd.     

Highly accurate calculation of radial spheroidal functions

A new method for calculating the radial spheroidal functions of the first kind is proposed for the arguments that are greater than unity in modulus. A well-known representation of these functions is refined and used for this purpose. The constructs and the software implementation proposed in the paper provide an efficient tool for the calculation of the functions with a desired accuracy in a wide range of parameters.     

A simple electronic speckle shearing interferometer

A new speckle shearing interferometer with simple setup is proposed. The interferometer can be converted easily from a speckle referenced speckle pattern interferometer into a speckle shearing interferometer and vice versa. A beamsplitter and a mirror are used to generate the shear. The amount of shear can be adjusted by simply rotating the mirror. The costs involved are low and it is particularly useful for fast inspection in non-destructive testing of structural integrity. Both the theoretical studies of the method of measurement and the experimental results are presented.     

高频聚焦换能器声场的激光测量法

本文描述了一种使用激光测振技术测量高频聚焦换能器声场布的方法，并给出了使用该方法对一种高频聚换能器进行测量的结果，通过理论计算对结果的正确性进行了验证。     

Hybrid numerical—experimental approach for investigation of dynamics of microcantilever relay system

The time average holography measurements of the vibrating microelectromechanical switch (MEMS) were performed in this study. Experimental measurement results exhibit good agreement with computer generated holographic interferogram analysis. The validation of experimental investigations versus numerical analysis provides the necessary background to analyze the dynamical characteristics of micromechanical systems in virtual numerical environments. Direct application of fringe counting techniques for reconstruction of motion from time average holograms cannot be straightforward if the analyzed micromechanical systems contain motion limiters. Modifications of a classical time average holographic technique enable qualitative analysis of MEMS and can be applied for investigation of dynamical properties of much broader classes of MEMS systems.     

Closed-form solutions for a rectangular layer with central crack under anti-plane shear stress

We consider the problem of determining the stress distributionin a finite rectangular elastic layer containing a Griffithcrack which is opened by internal shear stress acting alongthe length of the crack. The mode III crack is assumed to belocated in the middle plane of the rectangular layer. The followingtwo problems are considered: (A) the central crack is perpendicularto the two fixed lateral surfaces and parallel to the othertwo stress-free surfaces; (B) all the lateral surfaces of therectangular layer are clamped and the central crack is parallelto the two lateral surfaces. By using Fourier transformations,we reduce the solution of each problem to the solution of dualintegral equations with sine kernels and a weight function whichare solved exactly. Finally, we derive closed-form expressionsfor the stress intensity factor at the tip of the crack andthe numerical values for the stress intensity factor at theedges of the cracks are presented in the form of tables.     

A numerical and experimental investigation of the interactions between a non‐uniform planar array of incompressible free jets

The interaction between multiple incompressible air jets has been studied numerically and experimentally. The numerical predictions have been first validated using experimental data for a single jet configuration. The spreading features of five unequal jets in the configuration of one larger central jet surrounded by four smaller equi‐distant jets, have been studied, for different lateral spacing ratios of 1.5, 2.0 and 2.5 and a central jet Reynolds number of 1.24×105 (corresponding to a Mach number of 0.16). Flow of five equal jets has also been simulated, for the sake of comparison. The jet interactions commence at an axial distance of about 3–4 diameters and complete by an axial distance of about 10 diameters for the lowest spacing ratio of 1.5. For larger spacing ratios, the length required for the start and completion of jet interaction increase. Peripheral jets bend more towards the central jet and merge at a smaller distance, when their sizes are smaller than that of the central jet. The entrainment ratio for multiple jets is higher than that for a single jet. Excellent agreement is observed between the experimental data and theoretical predictions for both mean flow field and turbulent quantities, at regions away from the jet inlet. The potential core length and initial jet development, however, are not predicted very accurately due to differences in the assumed and actual velocity profiles at the jet inlet. Copyright © 2004 John Wiley & Sons, Ltd.     

Shear banding in strained semicrystalline polyamide 6 films as revealed by atomic force microscopy: Role of the amorphous phase

Atomic force microscopy (AFM) has been used to visualize the plastic deformation mechanisms that are responsible for the yielding of semicrystalline polymers of low degree of crystallinity (<50%). Indeed, AFM, if operated in suitable conditions, is able to image both the amorphous and the crystalline phases. Polyamide 6 films have been drawn at temperatures T < 160 °C. Postmortem AFM observations show that, at yield, shear bands nucleate and propagate in the amorphous phase. They cross the crystalline lamellae and run over the whole surface of the sample. By crossing the lamellae, they form nanoblocks of uniform size. Neither the size of the nanoblocks nor the angle between the tensile axis and the shear bands can be explained in terms of crystal plasticity. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 687–701, 2004