On additives, morphological evolution and dielectric breakdown in low density polyethylene

A series of low density polyethylene systems has been studied with respect to structural evolution and short-term dielectric breakdown behaviour. All materials were based upon a single polymer, that is commonly used in high voltage applications, but with different additives. In all three of these systems, multiple melting transitions were observed, as a result of molecular fractionation effects during crystallization. In the virgin polymer, a space-filling banded spherulitic morphology was found to develop at low temperatures (102 °C and below) whereas, at higher temperatures, only a few isolated axialites were observed. Inclusion of the antioxidant resulted in greatly increased nucleation densities, such that, at low temperatures, no evidence of spherulitic organisation remained. At higher temperatures, sheaf-like lamellar aggregates developed, which were much smaller and much more numerous than in the case of the virgin polymer. Further addition of dicumyl peroxide (DCP) resulted in the rapid formation of a crosslinked network at 200 °C. Some crosslinking also occurred at 150 °C, but over a much longer timescale. Where extensive crosslinking occurred prior to crystallization, the resulting gel inhibited structural development, such that only a few small, isolated sheaves were able to form at 102 °C. In view of the principal application area of this material, the breakdown strength of each of the above systems was then measured and the whole data set was analysed statistically. When structural factors were considered alongside the statistics, no clear trends emerged to indicate that either the compositional or morphological variations were reflected in the short-term electrical failure processes.     

SSIMS analysis of organics, polymer blends and interfaces

This paper gives a critical review on the applications of ToF SIMS in the areas of polymer additive characterization and in the study of polymer blends and interfaces. Polymer additives can readily be identified by ToF SIMS using their parent molecular ions or characteristic fragments. This analytical capability has been successfully applied to monitor the migration or segregation of additives during polymer processing. ToF SIMS is an ideal analytical tool for the study of polymer blends and interfaces because it is able to provide information on both surface composition and morphology. In combination with other analytical techniques such as AFM and XPS, ToF SIMS chemical imaging capability has opened up new horizons in the investigation of complex polymer blend systems. Finally the main advantages and limitations of ToF SIMS in these application areas are also discussed.     

表面活性剂对均相沉淀法制备单晶Ce2O(CO3)2￠H2O微粉形貌及 形成机理的影响

在尿素及硝酸铈的混合溶液中分别加入表面活性剂CTAB、 PEG19000、OP-10,利用均相沉淀法合成了不同形貌的CeO2超细前驱体Ce2O(COa)2·H2O,采用X射线衍射及透射电子显微镜等测试手段,对产品的物相和形貌进行了表征．实验结果表明,所得产品均为斜方晶系的单晶Ce2O(CO3)2·H2O,且表面活性剂的加入使晶体的晶化程度明显提高;添加不同的表面活性剂得到不同形貌尺寸的产物: 阳离子型表面活性剂CTAB对Ce2O(CO3)2·H2O晶体的形貌影响不大,所得产物尺寸变小,且分散性得到一定的改善;非离子型表面活性剂对所得产物的形貌影响显著．加入PEG19000和OP-10分别得到了形状排列有序的、尺寸较均匀的、较规则无团聚的微米棒及具有紧密结合中心的发散状的花样微粒．不同形貌前驱体的形成与晶粒形成生长机理的改变有关．     

Structural and optical characterization of the propolis films

We have performed structural and optical characterizations of the propolis (an organic entity of biological nature) films grown on various non-organic substrates. The films were grown from a propolis melt or a propolis alcohol solution. The crystal structure has been observed in the films precipitated from the solution onto substrates such as an amorphous glass and sapphire or semiconductor indium monoselenide. For any growth method, the propolis film is a semiconductor with the bandgap of 3.07 eV at 300 K that is confirmed by a maximum in photoluminescence spectra at 2.86 eV. We argue that propolis films might be used in various optoelectronic device applications.     

CRYSTAL STRUCTURE AND MORPHOLOGY OF NASCENT SAMPLES OF SYMMETRIC AROMATIC POLYESTERS——Ⅱ. POLY(p-PHENYLENE 2,6-NAPHTHALATE)

Confined thin film melt polymerization (CTFMP) of naphthalene chloride/hydroquinone (NCMQ, 1/1, molar)mixtures at polymerization temperatures (T_p) below ca. 300℃ resulted in relatively thick, elongated crystals. Polymerizationof NC/HQ above 300℃ between glass yielded well-formed lamellar crystals ca. 100 A thick. Phase Ⅰ and Ⅱ [001] EDpatterns were obtained for all T_p, the relative amount of phase Ⅰ increasing with T_p. Polymerization of naphthalenedicarboxylic acid/hydroquinione diacetate 1/1 mixtures at high T_p also yielded lamellar crystals that "curled up" off of thesubstrate. When the high temperature CTFMP polymerization was conducted between mica, aggregates of lamellae on-edgedeveloped but epitaxial growth did not occur. Epitaxial growth of lamellae between mica could be obtained, however, byconfined thin film solution polymerization, with both of the latter samples yielding apparently related ED patterns from adifferent unit cell than phase Ⅰ or Ⅱ. Fiber patterns, obtained from sheared samples, indicated considerably greater crystaldisorder than in the nascent crystals. Refinement of the phase Ⅰ unit cell parameters, based on the [001] and [01 1] EDpatterns, with modeling based on Cerius~2, suggests a monoclinic phase Ⅰ unit cell with a = 7.76, b = 5.71, c = 14.99 A, α = γ= 90°, β= 99.7°, ρ = 1.47 g/cm~3, space group P12_1/al.     

Morphology-dependent photoluminescence property of red-emitting LnOCl:Eu (Ln=La and Gd)

Three different synthetic methods, the liquid phase process in HCl solution, the solvothermal reaction, and the surfactant-assisted solvothermal reaction, were explored to selectively control the particle shape and to enhance the luminescence intensity of the PbFCl-type red-emitting oxychloride phosphors LnOCl:Eu (Ln=La and Gd). The solvothermal pressure facilitated the low-temperature crystallization of the rod-shape particles for both Ln=La and Gd. It is noted that LaOCl:Eu nanorods show highly porous particle surface and quite low photoemission intensity. In contrast, the solvothermal synthesis could highly enhance the red-emission of GdOCl:Eu with no porous surface so as to be comparable to that of commercial Y₂O₃:Eu phosphor. An addition of surfactant material during solvothermal reaction yielded a rhomboidal-shape phosphor particles with no porous surface for both Ln=La and Gd. Interestingly, the elimination of surface porosity by using a surfactant significantly increased the emission intensity of LaOCl:Eu. It is proposed that the application of solvothermal technique for the synthesis of the PbFCl-type oxychloride phosphors is very effective to selectively control the particle shape and consequently to enhance the photoemission intensity if we use an appropriate surfactant material.     

动,静态硫化（NR＋SBR）／PE共混体系的结构与性能

用TEM研究了(NR SBR)/PE共混体系经动、静态硫化后的形态结构及其与力学性能的关系。未硫化和静态硫化体系的形态结构与其组成有关,均以含量大的组份为连续相;对动态硫化体系,当(NR=SBR)/PE<70/30时,均以PE为连续相,其性能主要依赖于构成连续相组份的性质。 动态硫化体系的T_g值低于静态体系,随PE组份含量的增加变化不大,而静态硫化体系的T_g值则随PE含量增加向高温方向迁移。用DSC测得动态硫化体系的结晶度比静态体系的大。前者的应力-应变性能也低于后者。     

β晶型聚丙烯塑性形变过程中的形态变化

β晶型聚丙烯塑性形变过程中的形态变化沈静姝，任宏燕，况勋（中国科学院化学研究所高分子物理开放实验室，北京，１０００８０）史观一（中国科学院上海有机所，上海，２０００３２）关键词β晶型聚丙烯，塑性形变，形态全同立构聚丙烯的分子链都是３；螺旋链，但其晶体...     

胆甾液晶／聚合物多组分体系的结构与性能研究（Ⅲ）──ChN／poly（MMA－CO－BMA）混合体系的形态结构

应用Ｘ射线衍射、偏光显微镜及电子显微镜研究了胆甾液晶与甲基丙烯酸甲酯（ＭＭＡ）─甲基丙烯酸丁酯（ＢＭＡ）无规共聚物共混体系的形态结构。研究了体系的结晶态及液晶态的行为和共聚物含量及组成对光学织构的影响。     

ABS blends with phenoxy: morphology,thermal, mechanical and rheological properties

Blends of ABS (acrylonitrile–butadiene–styrene) with phenoxy(poly(hydroxyether bisphenol A)) were prepared using a Branender single screw extruder. Scanning and transmission electron micrographs (SEM, TEM) showed a typical two-phase morphology; particle-in-matrix (90/10) (ABS/phenoxy by weight), 70/30, 10/90), island/sea (30/70) and co-continuous (50/50) morphologies. The glass transition temperature (T_g) of SAN was almost unchanged in the blends, while the T_g of phenoxy increased by about 5 °C in the blends. The synergistic effect of tensile modulus and strength was noted in ABS-rich blends, where a drastic drop of ductility was seen, and the results were interpreted in terms of rubber particle migration form SAN to phenoxy phase, which was visualized by TEM. Melt viscosity showed yield in ABS-rich blends, and generally followed the log additivity.