Interface and defects engineering for multilayer laser coatings

High-reflective multilayer laser coatings are widely used in advanced optical systems from high power laser facilities to high precision metrology systems. However, the real interface quality and defects will significantly affect absorption/scattering losses and laser induced damage thresholds of multilayer coatings. With the recent advances in the control of coating design and deposition processes, these coating properties can be significantly improved when properly engineered the interface and defects. This paper reviews the recent progress in the physics of laser damage, optical losses and environmental stability involved in multilayer reflective coatings for high power nanosecond near-infrared lasers. We first provide an overview of the layer growth mechanisms, ways to control the microstructures and reduce layer roughness, as well as the nature of defects which are critical to the optical loss and laser induced damage. Then an overview of interface engineering based on the design of coating structure and the regulation of deposition materials reveals their ability to improve the laser induced damage threshold, reduce the backscattering, and realize the desirable properties of environmental stability and exceptional multifunctionality. Moreover, we describe the recent progress in the laser damage and scattering mechanism of nodule defects and give the approaches to suppress the defect-induced damage and scattering of the multilayer laser coatings. Finally, the present challenges and limitations of high-performance multilayer laser coatings are highlighted, along with the comments on likely trends in future.     

Strain induced strengthening of soft thermoplastic polyurethanes under cyclic deformation

We investigate the cyclic mechanical behavior in uniaxial tension of three different commercial thermoplastic polyurethane elastomers (TPU) often considered as a sustainable replacement for common filled elastomers. All TPU have similar hard segment contents and linear moduli but sensibly different large strain properties as shown by X-ray analysis. Despite these differences, we found a stiffening effect after conditioning in step cyclic loading which greatly differs from the common softening (also referred as Mullins effect) observed in chemically crosslinked filled rubbers. We propose that this self-reinforcement is related to the fragmentation of hard domains, naturally present in TPU, in smaller but more numerous sub-units that may act as new physical crosslinking points. The proposed stiffening mechanism is not dissimilar to the strain-induced crystallization observed in stretched natural rubber, but it presents a persistent nature. In particular, it may cause a local reinforcement where an inhomogeneous strain field is present, as is the case of a crack propagating in cyclic fatigue, providing a potential explanation for the well-known toughness and wear resistance of TPU.     

A Structural Entropy Measurement Principle of Propositional Formulas in Conjunctive Normal Form

The satisfiability (SAT) problem is a core problem in computer science. Existing studies have shown that most industrial SAT instances can be effectively solved by modern SAT solvers while random SAT instances cannot. It is believed that the structural characteristics of different SAT formula classes are the reasons behind this difference. In this paper, we study the structural properties of propositional formulas in conjunctive normal form (CNF) by the principle of structural entropy of formulas. First, we used structural entropy to measure the complex structure of a formula and found that the difficulty solving the formula is related to the structural entropy of the formula. The smaller the compressing information of a formula, the more difficult it is to solve the formula. Secondly, we proposed a λ-approximation strategy to approximate the structural entropy of large formulas. The experimental results showed that the proposed strategy can effectively approximate the structural entropy of the original formula and that the approximation ratio is more than 92%. Finally, we analyzed the structural properties of a formula in the solution process and found that a local search solver tends to select variables in different communities to perform the next round of searches during a search and that the structural entropy of a variable affects the probability of the variable being flipped. By using these conclusions, we also proposed an initial candidate solution generation strategy for a local search for SAT, and the experimental results showed that this strategy effectively improves the performance of the solvers CCAsat and Sparrow2011 when incorporated into these two solvers.     

氢化丁苯共聚物结构的核磁共振波谱表征Ⅱ.微观结构的定量计算

在氢化丁苯共聚物¹³C-NMR谱脂肪碳部分谱带归属的基础上,根据各谱带的主要来源,推导出六个二单元浓度的计算公式。计算出二单元、一单元的相对含量,各结构单元的数均序列长度、嵌段含量和其它结构参数。加氢前后的¹H-和¹³C-NMR谱的组成计算结果基本一致。初步探讨了作为粘度指数改进剂的氢化丁苯共聚物微观结构与性能的关系,为合成提供了依据。     

固体力学有限元体系的结构拓扑变化理论

本文是文[1]的继续.文[1]提出了杆件系统的结构拓扑变化理论和拓扑变化法本文将这一理论和方法推进到连续体有限元体系;且在此基础上揭示出有限元体系的一个新性质,称为基本位移之梯度的正交性定理,从而给出一套设计敏度的显式表达式,可直接用于计算.     

加肋圆柱壳在轴压作用下的屈曲和后屈曲

本文讨论完善和非完善的,纵向加肋和正交加肋圆柱壳在轴压作用下的屈曲和后屈曲性态.依据文[1]提供的圆柱薄壳屈曲的边界层理论及其分析方法,给出了加肋圆柱壳在轴压作用下的屈曲和后屈曲理论分析.本文同时讨论肋骨与壳板材料不同时对加肋圆柱壳屈曲和后屈曲性态的影响.     

单甲基原位改性SiO2疏水减反膜的制备与性能研究

 在碱性条件下通过TEOS和MTES的共水解缩聚反应制备了单甲基原位改性的SiO₂溶胶，并使用提拉法在K9玻璃基片上镀制了疏水减反膜。通过透射电镜（TEM）考察了镀膜溶胶的微结构，分别使用红外光谱（FTIR）分析了薄膜的组分，用原子力显微镜（AFM）观察了薄膜的表面形貌和起伏状况，用紫外可见光谱（UV-vis）考察了薄膜的减反射性能，用接触角仪测量了薄膜对水的接触角。并使用“R-on-1”的方式测量了薄膜在Nd:YAG激光（1 064 nm，1 ns）作用下的损伤阈值。结果表明，通过共水解缩聚反应可以把甲基引入镀膜溶胶簇团中，改善了溶胶簇团的网络结构，使薄膜得到相当好的疏水性能和更好的抗激光损伤性能，同时薄膜能保持较好的减反射性能。     

Laser-induced damage of Ta2O5/SiO2 narrow-band interference filters under different 1064 nm Nd:YAG laser modes

The laser-induced damage (LID) behavior of narrow-band interference filters was investigated with a Nd:YAG laser at 1064 nm under single-pulse mode and free-running mode. The absorption measurement of such coatings was performed with surface thermal lensing (STL) technique. The damage morphologies under the two different laser modes were also studied in detail. It was found that all the filters exhibited a pass-band-center-dependent absorption and laser-induced damage threshold (LIDT) behavior, but the damage morphologies were diverse. The explanation was given with the analysis of the electric field distribution and the operational behavior of the irradiation laser.     

Diffusion Structural Analysis Study of Titania Films Deposited by Sol-Gel Technique on Silica Glass

The diffusion structural analysis (DSA) was used to characterize microstructure changes of hydrous titania gel films under in situ conditions of heating. TG and DTA were used in order to elucidate the processes controlling the formation of anatase film during heating of hydrous titania gel film. The annealing of porosity and near surface structure defects of the dehydrated titania films was indicated by DSA in the temperature range 255–700°C as the decrease of radon release rate. It was demonstrated that the annealing was enhanced on heating in oxygen in comparison with heating in argon. The DSA experimental results were compared with model curves describing the radon diffusion mobility and the annealing of radon diffusion paths.