Variational Derivative for Buckling Loads of Beams and Frames

The finite-difference method is a numerical technique for obtaining approximate solutions to differential equations. The main objective of the present study is to give a new aspect to the finite-difference method by using a variational derivative. By applying this formulation, accurate values of the buckling loads of beams and frames with various end supports are obtained. The performance of this formulation is verified by comparison with numerical examples in the literature __________ Published in Prikladnaya Mekhanika, Vol. 41, No. 7, pp. 139–144, July 2005.     

A parallel cell‐based DSMC method on unstructured adaptive meshes

A parallel DSMC method based on a cell‐based data structure is developed for the efficient simulation of rarefied gas flows on PC‐clusters. Parallel computation is made by decomposing the computational domain into several subdomains. Dynamic load balancing between processors is achieved based on the number of simulation particles and the number of cells allocated in each subdomain. Adjustment of cell size is also made through mesh adaptation for the improvement of solution accuracy and the efficient usage of meshes. Applications were made for a two‐dimensional supersonic leading‐edge flow, the axi‐symmetric Rothe's nozzle, and the open hollow cylinder flare flow for validation. It was found that the present method is an efficient tool for the simulation of rarefied gas flows on PC‐based parallel machines. Copyright © 2004 John Wiley & Sons, Ltd.     

强流四脉冲电子束源实验研究

 为了进行强流多电子束源研究，对现有2MeV LIA 注入器进行了四脉冲改造，二极管脉冲电压约500kV。实验研究了天鹅绒阴极在四脉冲条件下的发射能力、传导电流负载效应以及阴极等离子体运动对阴极电子发射和束能量的影响。利用空间电荷限制流模型推算出阴极等离子体膨胀速率在1 ~4cm/μs之间。     

Randomization helps to perform independent tasks reliably

This paper is about algorithms that schedule tasks to be performed in a distributed failure‐prone environment, when processors communicate by message‐passing, and when tasks are independent and of unit length. The processors work under synchrony and may fail by crashing. Failure patterns are imposed by adversaries. Linearly‐bounded adversaries may fail up to a constant fraction of the processors. Weakly‐adaptive adversaries have to select, prior to the start of an execution, a subset of processors to be failure‐prone, and then may fail only the selected processors, at arbitrary steps, in the course of the execution. Strongly adaptive adversaries have a total number of failures as the only restriction on failure patterns. The measures of complexity are work, measured as the available processor steps, and communication, measured as the number of point‐to‐point messages. A randomized algorithm is developed, that attains both ??(n log*n) expected work and ??(n log*n) expected communication, against weakly‐adaptive linearly‐bounded adversaries, in the case when the numbers of tasks and processors are both equal to n. This is in contrast with performance of algorithms against strongly‐adaptive linearly‐bounded adversaries, which has to be Ω(n log n/log log n) in terms of work. © 2003 Wiley Periodicals, Inc. Random Struct. Alg., 2004     

遥感器CCD驱动器热设计及其在摄像过程中的温度变化

CCD驱动器是航天成像遥感器摄像过程中的主要热源之一。防止CCD驱动器过热是保证其正常工作的重要方面。介绍了遥感器的工作模式和对CCD驱动器采取的热控制措施。通过热平衡试验,利用回归的方法,对CCD驱动器在摄像过程中的温度变化规律进行了分析,同时对热控制效果进行了评估。CCD驱动器工作时升温速率在0.85℃/min左右,整个摄像过程中最高温度约为26℃,所实施的热控制措施效果理想。     

Load-Carrying Capacity of Circular Plates Made of a Fiber-Reinforced Composite

The load-carrying capacity of circular plates made of a fiber-reinforced composite and loaded with axisymmetric transverse forces under axisymmetric boundary conditions is investigated. The plates can be freely supported or clamped along their contour. To the known yield condition used, in the plane of main bending moments, there correspond irregular hexagons, which depend on the mechanical properties of composite constituents and some characteristic geometrical parameters. It is shown that, depending on the ratio of ultimate radial and circumferential bending moments, in the plastic state, the circular plates (the central part of the clamped plates) take the form of a cone or a frustum of cone. For each of the cases, the limit load is found, which is a function of the above-mentioned mechanical parameters. The statically allowable fields of bending moments and the corresponding allowable fields of deflection rates are determined. The solutions found are exact. Special cases for the freely supported plates are analyzed, and the results obtained are presented in the form of graphs.__________Translated from Mekhanika Kompozitnykh Materialov, Vol. 41, No. 2, pp. 177–192, March–April, 2005.     

Effect of a Shock Pulse on a Floating Ice Sheet

The vibrations of a viscoelastic plate lying on an elastic liquid base subjected to pulse loading have been studied theoretically and experimentally. The effect of the variable depth of the reservoir, plate thickness, and strain relaxation time on the value of the plate vibration amplitude and the length and curvature of the flexural gravity wave profile are analyzed. Good agreement of theoretical and experimental results is obtained.     

Strength of cylinder joint adhesively bonded by coupling

Summary A method of joining two metal cylindrical shafts with adhesive coupling is proposed. Two cylindrical shafts with the same diameter are connected by bonding through a cylindrical coupling with epoxy resin. The strength of the shaft joint under tensile loading and torsional loading is investigated analytically and experimentally. The stress and strain distributions of the shaft joint is analyzed by the finite element method. The analyzed strain distributions in the joint are compared with experimental values. The joint strength is predicted by applying the strength laws of shafts, coupling, adhesive layer and adhesive interface between shaft and adhesive coupling. The effects of the coupling dimension on the joint strength are examined. It is shown that the adhesive shaft joint can transfer the load by which the cylindrical shafts are plastically deformed.This paper was refined by the author, K. Ikegami, during statying at Technische Universität München under the support of Deutscher Akademischer Austauschdients. The author is grateful to Professor Lippmann of Technische Universität München who is the host professor of the support.     

Stability of bars made of linear elastic materials with voids

Summary Dynamic stability of an elastic bar with voids is considered. Using the Lyapunov approach some new sufficient stability conditions are obtained and explicit expressions for the critical load are derived.