A model for crack formation during active solid pyrolysis of a char-forming solid: crack patterns; surface area generation; volatile mass efflux

A model is developed for the formation and propagation of cracks in a material sample that is heated at its top surface, pyrolyses, and then thermally degrades to form char. In this work the sample is heated uniformly over its entire top surface by a hypothetical flame (a heat source). The pyrolysis mechanism is described by a one-step overall reaction that is dependent nonlinearly on the temperature (Arrhenius form). Stresses develop in response to the thermal degradation of the material by means of a shrinkage strain caused by local mass loss during pyrolysis. When the principal stress exceeds a prescribed threshold value, the material forms a local crack. Cracks are found to generally originate at the surface in response to heating, but occasionally they form in the bulk, away from ever-changing material boundaries. The resulting cracks evolve and form patterns whose characteristics are described. Quantities examined in detail are: the crack spacing in the pyrolysis zone; the crack length evolution; the formation and nature of crack loops which are defined as individual cracks that have joined to form loops that are disconnected from the remaining material; the formation of enhanced pyrolysis area; and the impact of all of the former quantities on mass flux. It is determined that the mass flux from the sample can be greatly enhanced over its nominal (non-cracking) counterpart. The mass efflux profile qualitatively resembles those observed in Cone Calorimeter tests.     

Quantum states in fabricating poly-Si films

The quantum states are presented in these processions of fabricating poly-Si films. Amorphous silicon films prepared by PECVD has been crystallized by conventional furnace annealing (FA) and rapid thermal annealing (RTA), respectively. It is found that the thin films grain size present quantum states with the increasing of the gas flow ratios of SiH₄, H₂ mixture, substrate temperatures, frequency power, annealing temperature and time.     

Effective magnetic properties of a composite material with circular conductive elements

Effective magnetic properties of a composite meta-material consisting of periodically arranged circular conductive elements are studied theoretically. A general expression for the effective bulk permeability is obtained with mutual effects and lattice ordering being taken into account. The resonance frequency of the permeability is found to be strongly dependent on the size and shape of the unit cell. Frequency dispersion of the permeability is studied with special attention paid to the frequency range, where negative values of the permeability are possible. Corresponding recommendations for optimisation of the meta-materials with negative permeability are made. The results are confirmed by numerical simulations of the finite structure behaviour in an external magnetic field. Received 19 April 2002 Published online 31 July 2002     

A dynamical test of phase transition order: New things in old places or old wine in new bottles

We first discuss nonlinear aspects of phase transition theory applied to a particular liquid crystal phase transition. A simple derivation is given to show how two coupled Goldstone modes (one appearing as gauge fluctuations of the ordered phase) can force a phase transition, against all expectations, to take place discontinuously (theory of Halperin, Lubensky, and Ma)-but the discontinuity may be immeasurably small. Then, we describe a new dynamical test of phase transition order, developed by Cladiset al., that turns out to be more sensitive than x-ray diffraction and adiabatic calorimetry. Quantitative data found by this new method are in excellent agreement with the measurements of adiabatic calorimetry and x-ray diffraction as well as expectations implicit in the predictions of HLM.This is the text of an after-banquet talk given at the CNLS Workshop on the Dynamics of Concentrated Systems.     

The Linear Fokker-Planck Equation for the Ornstein-Uhlenbeck Process as an (Almost) Nonlinear Kinetic Equation for an Isolated N-Particle System

It is long known that the Fokker-Planck equation with prescribed constant coefficients of diffusion and linear friction describes the ensemble average of the stochastic evolutions in velocity space of a Brownian test particle immersed in a heat bath of fixed temperature. Apparently, it is not so well known that the same partial differential equation, but now with constant coefficients which are functionals of the solution itself rather than being prescribed, describes the kinetic evolution (in the N→∞ limit) of an isolated N-particle system with certain stochastic interactions. Here we discuss in detail this recently discovered interpretation. An erratum to this article can be found at     

一维光学格子孤子的传输特性及控制研究

利用解析和数值方法研究了在具有横向折射率周期性调制的克尔型非线性介质中光学格子孤子的传输，得到了孤子参数的演化方程以及格子孤子的形成和稳定传输的条件.结果表明：当光束的入射角小于某临界角度时，光束可被类似波导形式的路径俘获而稳定传输，该临界角随折射率调制周期、调制深度的增加而增大，且光束越窄临界值越大.此外，线性空间啁啾虽然对光束传输的中心位置没有任何影响，但会导致光束发散从而破坏格子孤子的形成和稳定传输，对此提出了采用特定功率取值来补偿啁啾作用从而形成格子孤子的方案. 关键词： 光孤子 光学格子 光传输 矩方法     

Simulation of the nonlinear vibration of a string using the Cellular Automata based on the reflection rule

In this study, the nonlinear dynamic responses of a string are simulated using the Cellular Automata method based on the reflection rule. In the case of nonlinear systems, the velocity of wave propagation is not constant and depends on the amplitude. A new treatment of the dynamic time step is proposed for the Cellular Automata method considering the effect of the propagation velocity. As numerical examples, first, the dynamic responses of a string with linear characteristic are simulated using the Cellular Automata method. A typical resonance curve can be obtained. Second, the dynamic responses of a string with nonlinear characteristic are simulated using the proposed method. Some characteristic types of vibration can be obtained. It is concluded that the linear and nonlinear dynamic responses of a string may be obtained by simulation using the Cellular Automata method.     

Neutrino propagation in a weakly magnetized medium

Neutrino-photon processes, forbidden in vacuum, can take place in the presence of a thermal medium and/or an external electro-magnetic field, mediated by the corresponding charged leptons (real or virtual). Such interactions affect the propagation of neutrinos through a magnetized plasma. We investigate the neutrino-photon absorptive processes, at the one-loop level, for massless neutrinos in a weakly magnetized plasma. We find that there is no correction to the absorptive part of the axial-vector-vector amplitude due to the presence of a magnetic field, to the linear order in the field strength.     

Closed-form solutions for a rectangular layer with central crack under anti-plane shear stress

We consider the problem of determining the stress distributionin a finite rectangular elastic layer containing a Griffithcrack which is opened by internal shear stress acting alongthe length of the crack. The mode III crack is assumed to belocated in the middle plane of the rectangular layer. The followingtwo problems are considered: (A) the central crack is perpendicularto the two fixed lateral surfaces and parallel to the othertwo stress-free surfaces; (B) all the lateral surfaces of therectangular layer are clamped and the central crack is parallelto the two lateral surfaces. By using Fourier transformations,we reduce the solution of each problem to the solution of dualintegral equations with sine kernels and a weight function whichare solved exactly. Finally, we derive closed-form expressionsfor the stress intensity factor at the tip of the crack andthe numerical values for the stress intensity factor at theedges of the cracks are presented in the form of tables.     

In-Situ Intrinsic Interface Strength Measurement at Elevated Temperatures and its Relationship to Interfacial Structure

A previously developed laser spallation technique has been modified to measure the tensile strength of thin film interfaces in-situ at temperatures up to 1100°C. Tensile strengths of Nb/A-plane sapphire, FeCrAl/A-plane sapphire and FeCrAlY/A-plane sapphire were measured up to 950°C. The measured strengths at high temperatures were substantially lower compared with their corresponding strengths at ambient temperature. For example, at 850°C, the interface tensile strength for the Nb/sapphire (151 ± 17 MPa), FeCrAl/sapphire (62 ± 8 MPa) and FeCrAlY/sapphire (82 ± 11 MPa) interface systems were lower by factors of approximately, 3, 5, and 8, respectively, over their corresponding ambient values. These results underscore the importance of using such in-situ measured values under operating conditions as the failure criterion in any life prediction or reliability models of such coated systems where local interface temperature excursions are expected. The results on alloy film interfaces also demonstrate that the presence of Y increases the strength of FeCrAl/Al₂O₃ interfaces.